Lepro BG1 Smart LED Bulb
Model: BG1
Setting Up Your Smart LED Bulb
Step 1: Connect to Network
Turn on your phone's Bluetooth and connect to the WiFi network.
Step 2: Install the Light
Install the light bulb.
?
Step 3: Follow On-Screen Setup
Follow the on-screen steps to finish setup. This may involve connecting to device groups or rules.
Voice Control Integration ?️
Your Lepro BG1 Smart LED Bulb supports integration with popular voice assistants:
- Amazon Alexa: Use the Alexa app or Alexa Skill.
- Google Assistant: Use the Google Home app or Google Action.
If the light does not work, please go to your Amazon Alexa or Google Home app and click 'Discover Devices'.
How to Reset the Light
To reset the light, switch it off and on four times, with a 2-second interval between each cycle.
Action Sequence: [Power Off] ➡️ [Power On] ➡️ [Power Off] ➡️ [Power On] ➡️ [Power Off] ➡️ [Power On] ➡️ [Power Off] ➡️ [Power On]
Technical Specifications
Parameter | Value |
---|---|
Operation Frequency Range | 2412MHz-2462MHz (WiFi) 2402MHz-2480MHz (Bluetooth) |
Modulation Type | DSSS (DBPSK/DQPSK/CCK) OFDM (BPSK/QPSK/16QAM/64QAM) GFSK |
Antenna Type | Wire |
Note: This device does not support manual dimming. It only supports dimming via the app.
Regulatory Compliance
ISEDC Warning (Canada)
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
FCC Warning (USA)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
European Directive 2012/19/EC (WEEE)
This product is subject to the provisions of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products identified with this symbol may not be discarded with normal household waste, but must be taken to a collection point for recycling electric and electronic appliances. This recycling symbol marks e.g. an object or parts of the material as valuable for recycling. Recycling helps to reduce the consumption of raw materials and protect the environment.
[WEEE Recycling Symbol]
Manufacturer Information
LEPRO INNOVATION INC
3651 Lindell Road Suite D1048, Las Vegas, NV 89103, USA
Website: www.lepro.com
Phone: +1 866-287-2558
Email: cs@lepro.com
Le Ming Trading Inc.
801-6081 No. 3 Rd. Richmond, BC, V6Y 2B2, CA
Website: www.lepro.ca
Phone: +1 833-433-1453
Email: cs@lepro.ca
Made in China