User Guide for Uplink models including: HS2016 Wiring Uplink s Cellular Communicators, HS2016, Wiring Uplink s Cellular Communicators, Uplink s Cellular Communicators, Cellular Communicators
DSC NEO Power Series (HS2016/2032/2064/2128) Wiring Uplink's Cellular Communicators and Programming the Panel CAUTION: · It is advised that an experienced alarm installer programs the panel as further programming may be required to ensure proper performance and use of the full functionality. · Do not route any wiring over circuit board. · Full panel testing, and signal confirmation, must be completed by the installer. NEW FEATURE: For Uplink Communicators, the status of the panel can be retrieved not only from the status PGM but now also from the Open/Close reports from the dialler. Therefore, wiring the white wire and programming of the status PGM of the panel is optional. IMPORTANT NOTE: The Open/Close reporting needs to be enabled during the initial pairing procedure. Wiring the 5530M communicators to DSC NEO 1 of 3 Wiring and Programming Uplink Communicators to DSC NEO Wiring the 5530M with UDM to DSC NEO for remote upload/download. Programming the DSC NEO Alarm Panel via the Keypad Enable Contact ID reporting: Keypad Display Keypad Entry Action description Select: *85555 To enter in Programming mode Select: 301 To enter menu" First phone number" Select: 001 001 To select first phone number DFFFFF 123456*6*# Enter actual or non-existing number (any number will do, 123456 is an example) followed by *6* (F in hex). Select: 383 Enter Communication Options 4. Comm. Option 4: 2# Toggle 2 to OFF, to set the programmable account code in 310 to 4 digits. Select: 310 To enter menu "System account code". System Account: 000 To enter submenu for the whole system (001, 002... for more partitions) System Account: 1234 Enter 4-digit account number for CMS identification (1234 is an example) System Account: 001 To enter submenu for Partition 1 Part.1 Account: 1234# Enter 4-digit account number for CMS identification (1234 is an example) Select: 311 To enter menu "Reporting". Select: 001 Go to "Alarm restore" options. Toggle receiver#1 *# Press * to select "Y" (yes) "Alarm/Restore" events are reported to telephone number 1 Tamper restore: 002 To go to "Tamper/Tamper restore". Toggle receiver#1 *# Press * to select "Y" (yes) "Tamper/Tamper restore" events are reported to telephone number 1. 2 of 3 Opening/Closing Select: Enter Data: Enter Data: Select: Comms. Enabled: Wiring and Programming Uplink Communicators to DSC NEO 003 Go to "Open/Close" events. *## Press * to select "Y" (yes) "Open/Close" events are reported to telephone number 1, # to save, # to exit to main menu 350 To enter "Communicator Alarm Format" options. 001 To select phone number 1 03# 03 is for Contact ID. 380 Enter First Communication Options 1## Toggle 1 to ON, 3 and 4 must be off (DTMF touch-tone dialing, DTMF dialing for all attempts). Program Keyswitch zone and output: Keypad Display Select: Select: Zone definitions Zone 1 Momentary KSW Select: Toggle 1 Toggle Option 1 Select: PGM 1 PGM 1 PGM 1 Keypad Entry Action Description *85555 To enter in Programming mode. 001 Enter zone definition menu. * Enter Zone 1 definition. 066 To choose Momentary Keyswitch for Zone 1. ## To exit to main menu. 013 Enter First System Options (to configure Normally Closed Zones). * Press * or toggle buttons <> until 1 is OFF (all zones are wired as normally closed circuits with returns to COM terminal). ## Press ## to exit to main menu. 009 Enter I/O Programming menu. 001 To enter PGM 1 subsection. 115 To program the output to report Armed/Disarmed status. ## Press ## to exit to main menu. Programming the DSC NEO Alarm Panel via the Keypad for remote Upload/Download (UDL) Program the Panel for Upload/Download (UDL): Display Keypad Entry Action Description Date / Time Enter section Toggle option Enter section Enter Hex Data Enter section Enter Hex Data Enter section Enter Data Enter section Enter Data *8 + Inst. Code 401 1,3,6# 403 915500# 404 915500# 405 255# 406 001# Enter programming menu. Default installer code is "5555". First downloading options toggle menu 1 and 3 should be disabled. 6 should be enabled. Press # to exit. DLS downloading access code. Set this field's value to its default. Press # to exit. Panel ID code. Set this field's value to its default. Press # to exit. Double call timer address Disable double call. Number of rings address Set the panel to answer on the first ring. 3 of 3Microsoft Word for Microsoft 365