TaylorPneumatic.com – Taylor Pneumatic Tool Company
Instructions for Taylor models including: T-2X Rivet Hammer, T-2X, Rivet Hammer, Hammer
TaylorPneumatic.com – Taylor Pneumatic Tool Company
T-7555 5" DA Sander 3/16" Orbit – Taylor Pneumatic Tool Company
T-7758RE 1/4" Extended Die Grinder - Rear Exhaust – Taylor Pneumatic Tool Company
File Info : application/pdf, 2 Pages, 1,018.13KB
DocumentDocumentT-2X Aircraft T-3X Riveting T-4X Hammers 4X 3X 2X OILING INSTRUCTIONS: OIL AFTER EACH USE WITH A COUPLE DROPS OF AIRTOOL OIL THROUGH THE AIR INLET. RUN FOR ONE SECOND TO COAT ALL INTERNAL PARTS USE 90 PSI MAXIMUM Ref # Part # Description 1 234X01 Handle 1 234X01A Handle Complete (Includes parts #1,9,10,11, 12,13,14,15,16,17,&18) 2 2X02 2X Cylinder 2 3X02 3X Cylinder 2 4X02 4X Cylinder 3 2X03 2X Piston 3 34X03 3X, 4X Piston 4 234X04 Bushing 5 234X05 Valve Block 6 234X06 Valve 7 234X07 Pin 8 234X08 Valve Seat 9 234X09 Throttle Bushing 10 234X10 Inlet Bushing 11 234X11 Valve Stem 12 234X12 O-Ring Qty. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Ref # 13 14 15 16 17 18 19 20 21 22 Part # 234X13 234X14 234X15 234X16 234X17 234X18A 234X19 234X20 T-5120 T-5210 Description Spring Plug Pin Pin Assistant Lever Lever Stopper Pin Exhaust Cover Quick Change Spring (option) Beehive Spring Qty. 1 1 1 1 1 1 1 1 1 T-5710 T-7922 T-7922R T-8004 OPTIONAL EXTRAS Multi Position Regulater Hose Swivel Hose Swivel w/ reg. Airtool Oil 505 N. Railroad Ave. (33435) P.O. Box 1117 (33425) Boynton Beach, Florida FOR WARRANTY INFORMATION & wWwAwRR.tAaNyTlYoRrpEnGIeSuTRmAaTtIOicN.cVoISmIT 0523TPTC /all rights reserved /COPYRIGHT 2023/ final Ph. (561) 732-1111 Fax (561) 731-4412 Toll Free 800-805-8665 General Air Hammer Maintenance T-7111,T-7151, T-1X, T-1XS,T-2X, T-3X, T-4X,& XS,5X,7X,9X, T-#2,#3,#4 & T-#24B, T-#34B & T-#44B - OILING & SPECIFIC HAMMER INSTRUCTIONS: *ALWAY USE CLEAN DRY COMPRESSED AIR @ OR BELOW 90 PSI. *USING DIRTY AIR CAN CAUSE THE VALVES OR PISTON TO JAM AND VOIDS THE WARRANTY. *IF AIR IS WET, THE INSIDE OF THE TOOL CAN RUST AND VOIDS THE WARRANTY. *USING MORE THAN 90 PSI CAN DAMAGE THE VALVES AND PISTON (THEY ARE ONLY DESIGNED TO TAKE SO MUCH PRESSURE), USING HIGH PRESSURE VOIDS THE WARRANTY. *NEVER DRY FIRE TOOLS. THEY NEED TO BE AGAINST THE CHISEL AND WORK BEFORE THE TRIGGER IS DEPRESSED. IF THE TOOL IS DRY FIRED DAMAGE TO THE PISTON AND BARREL MAY OCCUR AND THIS WILL VOID THE WARRANTY. * ALWAYS CHECK TO BE SURE THAT THE BARREL IS TIGHT IN THE HANDLE. LOOSE HANDLES CAN DAMAGE THE HANDLE THREADS AND VOID THE WARRANTY. OIL AFTER EACH USE WITH 1/2 TEASPOON OF AIRTOOL OIL THROUGH THE AIR INLET. RUN FOR ONE SECOND TO COAT ALL INTERNAL PARTS. - GENERAL INSTRUCTIONS 1. ALWAYS DISCONNECT THE TOOL FROM AIR SOURCE WHEN CHANGING ACCESSORIES OR SERVICING THE TOOL. 2. USE SAFETY GLASSES, FULL FACE SHIELDS, HEARING PROTECTION AND GLOVES. 3. USE WHIP HOSE FOR QUICK DISCONNECTS. 4. VIBRATION MAY BE HARMFUL TO YOUR ARMS AND HANDS. WEAR PROTECTION. 5. INSPECT THE TOOL AND AIR SUPPLY ON A REGULAR BASIS. 6. DO NOT REMOVE GUARDS OR SAFETY DEVICES. DO NOT MODIFY OR DEFEAT SAFETY DEVICES. 7. DO NOT MAKE CONTACT WITH ELECTRICAL LINES. 8. LEAVE TRIGGER OFF BEFORE CONNECTING THE TOOL TO THE AIR SUPPLY. AVOID ACCIDENTAL STARTS. 9. WEAR THE PROPER CLOTHING. DO NOT WEAR JEWELRY, LOOSE CLOTHING, OR LONG HAIR AS IT CAN GET CAUGHT IN ROTATING PARTS. KEEP GLOVES AWAY FROM MOVING PARTS. 10. DO NOT WORK IN HAZARDOUS ATMOSPHERES WHERE SPARKS COULD IGNITE OR DETONATE FUMES. 11. WATCH WHAT YOU ARE DOING. USE COMMON SENSE WHEN OPERATING PNEUMATIC TOOLS. DO NOT USE PNEUMATIC TOOLS WHEN TIRED OR UNDER THE INFLUENCE OF MEDICATION, ALCOHOL OR DRUGS. SERIOUS PERSONAL INJURY MAY RESULT FROM A MOMENTS INATTENTION. 12. USE 90 PSI AT THE TOOL. USE 3/8", 1/2" or 3/4" HOSE OR LARGER WITH FITTINGS 9/32 MINIMUM I.D. AS SPECIFIED 13. ONLY USE CLEAN DRY COMPRESSED AIR. NEVER USE OXYGEN, CARBON DIOXIDE, COMBUSTIBLE GASES OR ANY OTHER BOTTLED GAS TO POWER THIS TOOL. 14. SECURE YOUR WORK BEFORE STARTING - USE CLAMPS OR FIND A SUITABLE WAY TO MAINTAIN STABILITY. 15. STORE TOOLS IN A CLEAN DRY ENVIRONMENT. 16. DO NOT USE DAMAGED TOOLS - MARK, AND RETURN FOR SERVICE. 17. NEVER FORCE THE TOOL, LET THE TOOL DO THE WORK. 18. STOP USE IMMEDIATELY IF TOOL IS MAKING AN UNUSUAL NOISE OR VIBRATION. HAVE TOOL CHECKED BY PROFESSIONAL TECHNICIAN. 19. WORK IN A WELL VENTILATED AREA AND USE APPROVED PERSONAL PROTECTIVE EQUIPMENT SUCH AS DUST MASKS, THAT ARE SPECIFICALLY DESIGNED TO FILTER OUT MICROSCOPIC PARTICLES. SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING AND OTHER CONSTRUCTION ACTIVITIES CONTAIN CHEMICALS KNOWN TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. SOME EXAMPLES OF THESE CHEMICALS ARE: CRYSTALLINE SILICA FROM BRICKS, CEMENT AND OTHER MASONRY PRODUCTS, ARSENIC AND CHROMIUM FROM CHEMICALLY TREATED LUMBER AND LEAD FROM LEAD BASED PAINTS. YOUR RISK FROM EXPOSURE VARIES, DEPENDING ON HOW OFTEN YOU DO THIS TYPE OF WORK. TO REDUCE YOUR EXPOSURE TO THESE CHEMICALS WEAR PROTECTIVE MASKS AND CLOTHING. 20. KEEP CHILDREN, PETS AND BYSTANDERS AWAY WHILE OPERATING A PNEUMATIC TOOL. DISTRACTIONS CAN CAUSE YOU TO LOSE CONTROL. PROTECT OTHERS IN THE WORK AREA FROM DEBRIS SUCH AS METAL FILINGS AND SPARKS. PROVIDE BARRIERS OR SHIELDS AS NEEDED. 21. THESE WARNINGS AND INSTRUCTIONS CAN NOT COVER ALL POSSIBLE CONDITIONS OR SITUATIONS. THE OPERATOR MUST UNDERSTAND THAT COMMON SENSE AND CAUTIONS ARE FACTORS WHICH CAN NOT BE BUILT INTO THE PRODUCT BUT MUST BE SUPPLIED BY THE OPERATOR. 505 N Railroad Ave. (33435) P.O. Box 1117 (33425) Boynton Beach, Florida SEE OUR CATALOG at www.taylorpneumatic.com 11/15TPTC /all rights reserved /COPYRIGHT 2015 / final PH. 561-732-1111 FAX 561-731-4412 TOLL FREE 800-805-8665