User Manual for Speco models including: AIOS06 AIPK1 Single Door 2 Wire Video Intercom Kit, AIOS06, AIPK1 Single Door 2 Wire Video Intercom Kit, 2 Wire Video Intercom Kit, Video Intercom Kit, Intercom Kit
Speco AIPK1 Single Door 2-Wire Video Intercom Kit | 123 Security Products
User Manual AIOS06 Outdoor Station 2-Wire Outdoor Station (Surface Mounting) AIOS06 User Manual_V1.0 Content Chapter 1 Function Overview ........................................................................ 1 1.1 Function .................................................................................................. 1 1.2 Parameter ............................................................................................... 1 Chapter 2 Product Introduction ..................................................................... 2 2.1 Front View............................................................................................... 2 2.2 Product Dimension ................................................................................ 3 2.3 Interface Introduction ............................................................................ 4 Chapter 3 Installation...................................................................................... 5 3.1 Installation Height.................................................................................. 5 3.2 Installation Steps ................................................................................... 6 Chapter 4 User Instruction ............................................................................. 8 4.1 Calling resident ...................................................................................... 8 4.2 Unlock ..................................................................................................... 8 4.3 External camera extension ................................................................... 9 Chapter 5 Settings .......................................................................................... 9 5.1 Factory Setting ....................................................................................... 9 5.2 Unlock Time Setting .............................................................................. 9 5.3 Calling Volume Setting .......................................................................... 9 5.4 Address Setting...................................................................................... 9 Chapter 1 Function Overview This product is an Outdoor Station in 2-wire analog video door phone system. Twin-core cable is adopted to connect into the system. It supports video intercom with Indoor Monitor and door unlocking. With the Relay Actuator Control Module connected, it also supports unlocking a 2nd door. 1.1 Function Support calling to Indoor Monitor 1 and Indoor Monitor 2 Adjustable unlock time Door status detection Support external camera extension (Camera Interface Module is needed ) 1.2 Parameter Working Parameter Working VoltageDC 24~32V Working Temperature-25~55 Storage Temperature-40~70 Camera TypeCMOS View Angle90°(Horizontal ) White BalanceAutomatic Static Current 20mA (DC 30V) Working Current 110mA (DC 30V) Dimension(H/W/D)168×86×26mm Resolution600TVL Min. Illumination0.1 lux Fill-in Light TypeLight Sensitive Diode 1 Chapter 2 Product Introduction 2.1 Front View 2 2.2 Product Dimension Unitmm 3 2.3 Interface Introduction Interface Unlock time setting; Interface calling volume setting; Interface BUS-A , BUS-B: Bus interface; NO, COM , NC: Normal open/close interface; GS: Door status detection interface; DOOR SW: Unlock inside; GND: Common ground. 4 Chapter 3 Installation 3.1 Installation Height Suggested Installation Height: camera is 1.6m above the ground 5 3.2 Installation Steps Step 1: Drill holes on the wall according to the installation size (149.5×64.5mm), fix the capsules into the hole (it is recommended to align the device to the center of the reference line ), then place the device and fasten with self-tapping screws(Pic 2). Pic 1 Pic 2 Step 2: Fill in the apartment's information, and install it in the name tag area, then complete the wiring (Pic 3). Step 3: Assemble the metal case onto the device, and fasten with plum blossom screw (Pic 4). name tag pager name tag cover Pic 3 Pic 4 6 3.3 System Wiring Indoor Monitor Remarks The outdoor station is suitable for one or two apartments, and it is possible to make connection with large system. Supports multiple Indoor Monitors (maximum Qty is 4pcs) in one apartment, address of all Indoor Monitors in one apartment should be same. Attention: When there's multiple monitors in one apartment, only one can be set as master Indoor Monitor, otherwise there will be an over-current. Please check the interface introduction for how to set a master Indoor Monitor. When there are multiple Indoor Monitors in one apartment and a call is made, all Indoor Monitors will ring at the same time but only the screen of the master Indoor Monitor is turned on, and after one of the monitors pick up the call, the rest of the monitors hang up. 7 Power supply is limited, so only 2 monitors are allowed to be operated at the same time (intercom function is not limited). The wiring above is recommended for two apartments. If there are multiple Indoor Monitors in one apartment, wiring with distributors (Star topology) are recommended. Chapter 4 User Instruction 4.1 Calling resident Single Calling Function Outdoor Station AIOS06 : By short pressing the button of AIOS06 (Upper button/ Lower button), visitor starts to call the same Indoor Monitor 1, whose ringtone will echo back. Repeating pressing the buttons during the call, then the countdown will be reset (each call waits for 30 seconds); if there's no answer in 30 seconds, the call will end. Dual Calling Buttons Outdoor Station: It supports calling Indoor Monitor 1 and Indoor Monitor 2. By short pressing the lower button of the Dual Calling Buttons Outdoor Station, visitor starts to call Indoor Monitor 1. By short press the upper button of Dual Calling Buttons Outdoor Station, visitor starts to call Indoor Monitor 2. If the upper button is pressed while calling Indoor Monitor 1, then the call will be switched to Indoor Monitor 2 and the countdown will be reset (each call waits for 30 seconds). If there's no answer in 30 seconds, the call will be ended. 4.2 Unlock 1) Unlock by Indoor Monitor Door can be opened by Indoor Monitor when it's communicating with Outdoor Station or under surveillance mode. 2) Unlock by external push button As there is an interface for integration of external push buttons, when this is connected, a normal push button can be used to unlock the door. 8 4.3 External camera extension Outdoor Station is supported to work with Camera Interface for external camera extension. As Outdoor Station is configured with Camera Interface, while Outdoor Station is calling Indoor Monitor, or Indoor Monitor is monitoring Outdoor Station, the displays can switch between different cameras. For further information please refer to the user manual of Camera Interface. Chapter 5 Settings 5.1 Factory Setting Cut off the power of the outdoor station and power on within 60 seconds, long press any button on the outdoor station for 3 seconds. After a long beep, factory reset is done. 5.2 Unlock Time Setting The default unlock time is 1 second. There is an adjustable potentiometer on the back side of the outdoor station(), unlock time can be adjusted by ratio of 180° from 1 second to 10 seconds, lengthen in anticlockwise direction, shorten in clockwise direction. 5.3 Calling Volume Setting The default calling volume is in middle value. There is an adjustable potentiometer on the back side of the outdoor station(), unlock time can be adjusted by ratio of 180°. Users can freely adjust the calling volume according to the installation environment. 5.4 Address Setting In standby mode, press any button from outdoor station for 3 seconds, the device will beep twice to enter the address setting mode. Press the button to add address number from 1-5, after each short press, the device will beep different times to show what number it is with. For example: a device with NO. 1 will beep once, if it's set to NO. 5, it will beep 5 times 9 after short press. When a device is already NO. 5, one short press will make this device become device NO. 1, cyclically. After address setting, press any button for 3 seconds to exit setting mode with a long beep, or the setting mode will exit automatically if no operation for over 15 seconds. 10Microsoft Word for Microsoft 365