SUBMITTAL DATA SHEET
Local Interlocking Kit for Heat Pump
HP6000WF-MA-K2
Version for heat pumps manufactured by MIDEA (with Sinopé HP6000WF-MA interface)
No Internet connection required
Wi-Fi enabled
Physical Description & Dimensions
Sinopé Wi-Fi Interface: A black USB-style device with a Sinopé logo. Dimensions are approximately 23.01mm [0.91po] x 40.84mm [1.61po] x 8.07mm [0.32po]. The back view shows a USB connector and status indicators. Dimensions are approximately 53.52mm [2.11po] x 8.07mm [0.32po].
Smart Thermostat Lite: Front view shows a digital display with '21' and two circular buttons. Dimensions are approximately 115mm wide and 127.3mm high. Side view shows a depth of approximately 32mm.
*Validate heat pump models compatible with interfaces
Specifications for the Kit
Type
- Turnkey solution for single-zone ductless heat pumps that prevents simultaneous activation of electric heating and air-conditioning in the same zone
- Multi-zone and ducted expansion available on request
Internet connection
- Not required
Communication
- Protocol: Wi-Fi
- Standard: IEEE 802.11 b/g/n
- Frequency: 2.4 GHz
- Encryption key: WPA2
Devices
- Kit includes:
- 1 x Wi-Fi thermostat for electric heating (TH1134WF)
- 1 x Wi-Fi interface for compatible* HP6000WF-MA ductless heat pump
- Devices pre-associated together and factory pre-programmed by Sinopé Technologies
- Devices in the kit must not be sold separately
- Devices all have the same reference number (one number per factory-pre-associated set)
How it works
- Heat pump control:
- The user uses the heat pump's remote control.
- Wi-Fi communication between devices:
- The TH1134WF thermostat connects to the HP6000WF-MA's secure Wi-Fi network.
- The HP6000WF interface, connected to the heat pump, transmits its status over its network.
- The TH1134WF thermostat reads the HP6000WF-MA status transmitted over the network.
- Device coordination:
- When the heat pump is in cooling or automatic mode, the thermostat automatically stops its heating.
- In heating, fan or OFF mode, the thermostat can activate heating without interfering with the heat pump.
Specific scenarios
- Loss of communication or malfunction:
- If there is a problem with the HP6000WF interface or the heat pump for more than 30 minutes, the thermostat will start heating again.
- Thermostat display in cooling mode:
- If the heat pump is in cooling mode and the user cannot interact with the thermostat, the display shows “IL” when the user attempts to change the setpoint. This indicates that heating is deactivated.
Evolutivity
- If the user connects the HP6000WF-MA and TH1134WF to the Internet and creates an account on Sinopé's Neviweb application (residential user) or on the Sinopé Smart Systems platform (commercial user who must contact a Sinopé representative beforehand):
- Interlock settings are retained.
- The user can add other Sinopé devices.
*Validate heat pump models compatible with interfaces
Specifications for the Wi-Fi Ductless Heat Pump Interface
Type
- Interface for Midea-manufactured and compatible heat pump/air conditioner mini splits*
Transmitter module
- IC: 21098-ESPC6WROOMI
- FCC ID: 2AC7Z-ESPC6WROOMI
Power supply
- Via heat pump / air conditioner indoor unit's communication port
Temperature range
- Operating: 0 °C to 40 °C (32 °F to 104 °F)
- Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Installation
- Connect the interface directly to the indoor unit's USB communication port (see "Installation diagrams" below).
- USB type A port
Compatible devices
- Heat pumps and air conditioners mini splits with compatible communication port (see compatible heat pump)
Control (if connected to Internet)**
- Modes: Cooling, heating, dry, fan and OFF
- Adjusting the orientation of heat pump shutters
- Adjusting the ventilation intensity
- Activate or deactivate the display on the indoor unit of the heat pump
- Setpoint control
Certifications
- Complies with FCC15 & NMB-0003
Warranty
- 3 years
Specifications for the Smart Wi-Fi Thermostat
Type
- Smart thermostat
- TRIAC switching
Transmitter module
- FCC ID: 2AC7Z-ESPC6WROOMI
- IC: ESP32-C6-WROOM-1
Power supply
- 120/208/240 Vac, 60 Hz
Power (Puissance)
Maximum load (resistive load only)
- 16.7 A / 4000 W @ 240 Vac
- 16.7 A / 2000 W @ 120 Vac
Minimum load (baseboard, convector & radiant ceiling)
- 2 A / 500 W @ 240 Vac
- 2 A / 250 W @ 120 Vac
Minimum load (fan-forced convector)
- 4.16 A / 1000 W @ 240 Vac
- 4.16 A / 500 W @ 120 Vac
- One fan-forced convector per thermostat can be connected
Control
- 15-minute cycle (fan-forced) or 15-second cycle (convector)
- Device resolution: 0.5°C (1°F).
- Display resolution: 1°C (2°F).
- Accuracy: ± 0.15°C (0.27°F) for 15-second cycles
- Accuracy: ± 0.5 °C (1 °F) for 10-minute cycles
Temperature range
- Setting: 5 °C to 30 °C (41 °F to 86 °F)
- Display: 0 °C to 50 °C (32 °F to 99 °F)
- Operation: 0 °C to 50 °C (32 °F to 122 °F)
- Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Display
- Digital display with black backlighting
- Fan-forced convector mode and keypad lock display (when activated)
- Temperature display format (°C or °F)
Installation
- 3-wire thermostat – compatible with 4-wire systems
Compatible Heating Devices & Features
Compatible heating devices
- Electric baseboard
- Convector
- Fan-forced convector
- Radiant ceiling
Features (if connected to Internet)
- If you are a homeowner, you will use the Sinopé Neviweb application.
- In the case of a renting user, he will have to contact his manager. The latter should contact a Sinopé representative to integrate the devices into the Sinopé Smart Systems commercial platform.
- Lockable buttons
- Customizable minimum and maximum temperatures available for thermostat control
- Schedule programming
Certifications
- Tested in compliance with CSA-C828-19
- Complies with standards
- CAN/CSA STD 22.2 nos,
- E60730-1-5 & E60730-2-9,
- FCC CFR 47 Title 15 Class B,
- CAN ICES-3(B)/NMB-3(B)
Warranty
- 3 years
Installation Diagrams
Thermostat Installation
240V Installation
Diagram shows a thermostat connected to an electrical panel ('Panneau électrique') and an electric baseboard heater ('Plinthe électrique'). Wires are labeled: Blue - Charge, Red - Neutre/Ligne 2, Black - Ligne 1. L1 and L2 (240V) connections are indicated.
120V Installation
Diagram shows a thermostat connected to an electrical panel ('Panneau électrique') and an electric baseboard heater ('Plinthe électrique'). Wires are labeled: Blue - Charge, Red - Neutre/Ligne 2, Black - Ligne 1. L1 and L2 (240V) connections are indicated.
Ductless Heat Pump Interface (Midea) Installation
Steps:
- 1. Open the front panel of the indoor unit.
- 2. Insert the interface into the dedicated port in the cover of the indoor unit.
- 3. Close the cover of the indoor unit.
Diagrams illustrate the three steps for installing the Wi-Fi interface into a Midea ductless heat pump indoor unit. Step 1 shows opening the panel. Step 2 shows inserting the interface into a port. Step 3 shows closing the panel.
Model Information
| No. product | Description | Volts | Watts | Qty |
|---|---|---|---|---|
| HP6000WF-MA-K2 | Local interlocking kit for compatible MIDEA ductless heat pumps | - | - | - |
Specifications are subject to change without notice
Installation Compliance Certification
The signature certifies that the installation complies with the above installation diagrams.
| Designation | Profession | Signature |
|---|---|---|
| Project's name: | ||
| Address: | ||
| Brand and models of wall-mounted units installed: | ||
| Promotor: | ||
| Builder: | ||
| Consulting engineer: | ||
| Contractor #1: | ||
| Contractor #2: | ||
| Contractor #3: | ||
| Date: |
