Sussex Taps – Making it right entirely in Australia since 1997
Sussex Taps – Making it right entirely in Australia since 1997
Instructions for SUSSEX models including: BMDSRH, CBM, Suba Mixer Diverter System Dress Kit, BMDSRH Suba Mixer Diverter System Dress Kit, Mixer Diverter System Dress Kit, Diverter System Dress Kit, System Dress Kit
File Info : application/pdf, 2 Pages, 845.54KB
DocumentDocumentSuba Mixer diverter system Dress kit Product code: CBM Product code BMDSRH Mixer diverter system 1 Stud Face Finished Wall Surface Apply Silicone NOGGING Masterfit 80 mm Backplate Handle Body Apply Silicone Set Screw 2 NOGGING Masterfit Stud Face Finished Wall Surface Apply Silicone 80 mm Backplate Handle Body Apply Silicone Set Screw Mixer dress kit - Remove Mixer protective cover. - Using silicon, seal the wall surface around the Mixer. - Apply a small amount of silicon to the rear of the backplate prior to mounting onto the wall. - Fit the handle body onto the Mixer Cartridge Lever ensuring the Handle is fully engaged. - Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well). Diverter dress kit - Remove Mixer protective cover. - Using silicone, seal the wall surface around the Diverter. - Apply a small amount of silicone to the rear of the backplate prior to mounting onto the wall. - Fit the Handle Body onto the Diver ter Adapter, ensure the Handle is fully engaged. - Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well). To complete the installation, operate the Mixer(s) checking the flow of both hot and cold water from Outlet. Check all fittings and fixtures for water leaks. sussextaps.com.au AS/NZS 3718:2005 LIC. 20081 Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003 Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c Copyright © Sussex Taps. Suba Mixer diverter system Rough in Product code: CBM Product code BMDSRH Mixer diverter system 1 Vi ew f ro m ab ov e This Outlet Side 1 UP Masterfit 70 Diverter Min. 8mm NOGGING Mixer 90 30-32mm Stud face Wall Covering Max. 30mm Dress Ring Back Plate Handle Body No te: Th e di ve rt er i s of t he d ial ty pe , ro ta te h andl e to d irec t Outlet 1 Pipe Connections Diverter Mixer Cold Outlet 2 Hot Rough in plumbing - Prior to installing, calculate the finished wall thickness, maximum is 30mm thick, contact manufacturer for further options. - If Wall thickness is greater than 30mm, contact manufacturer for further options. - Prepare a Nogging to be fixed parallel between the Wall Studs. - The Nogging must be fitted to enable the base of the Masterfit to be 30-32mm back from the Stud Face. - The Masterfit will be marked "This side Up" to indicate orientation. - Using the screws (x4) provided, mount the Masterfit to the Nogging. Ensure the Masterfit is level and square. Pipe connections - The Hot and Cold ports are marked on the Masterfit. (Mixers have individual Hot/Cold inlet ports). - Flush all water feed lines. All lines must be free from any dirt and debris before connecting to the Masterfit. - Connect Hot and Cold lines to the corresponding 1/2" BSP ports of the Masterfit. (see Drawing) - Do not remove any factory fitted pressure plugs or Fixings. - Once all water connections are made, check Hot/Cold water flow by operating the Mixer Cartridge. - Check all fittings and fixtures for leaks. - Leave the Mixer(s) in the closed position and replace the Mixer protective cover. - Store the Dress Kit in a safe place until required (see Dress Finishing Guide) Plumber note - On-site high pressure line testing must be conducted with the Mixer in the closed position. (STATIC TEST ONLY) - Under no circumstances is the Mixer to be opened when exceeding the maximum stated water pressure. - At the completion of the testing, do not relieve any high pressure by opening the Mixer. - Exposing the internals of the Mixer Cartridge to higher than specified water pressures, will void the manufacturer's warranty. sussextaps.com.au AS/NZS 3718:2005 LIC. 20081 Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003 Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c Copyright © Sussex Taps.