User Manual for Aplus Hardware models including: AP7000RF, 2AZOB-AP7000RF, 2AZOBAP7000RF, AP7000RF Wireless Linkable Wall Light, AP7000RF, Wireless Linkable Wall Light
Aplus Hardware Corp. AP7000RF Wireless linkable wall light 2AZOB-AP7000RF 2AZOBAP7000RF ap7000rf
File Info : application/pdf, 3 Pages, 731.39KB
DocumentDocument- AP7000RF Read the safety precautions in this section before installing, powering, operating or servicing this product. USER MANUAL SAFETY PRECAUTIONS WARNING! Safety hazard. Can result in shock from battery or product damage. Lighting fixture is for INDOOR use ONLY. Do not use parts or materials other than the supplier parts to install this product To avoid accidents do not change or modify this product in any form or method. Do not replace batteries when your hands are wet to avoid risk of shock or product malfunction. Do not look directly at LED to minimize the risk of eye irritation or injury. Not for use in high temperature, humidity, direct sunlight or where it may be exposed to rain or water. Install the device according to the user manual and installation instructions. Use this product within the room temperature range of 0-40 (32-104). Cleaning and Installation Care. Wipe and clean product with a dry soft cloth ONLY. DO NOT spray any type of cleaning solution directly onto the product as it will damage the device. Never clean with harsh chemicals such as alcohol or solvents. Ensure that product is mounted securely to the wall to prevent personal injury and /or product damage as a result of product falling. Do not install near electric doors or other devices that use radio waves as to not interfere with this product or radio wave devices. Do not mix old and new batteries, alkaline and carbon-zinc or rechargeable batteries. Do not install this product near high temperature equipment such as heaters to avoid sensor failure. Be careful of battery polarity when installing batteries. If the product malfunctions in any way, stop using the product and contact the original seller. Remove batteries when not in use for long periods. About radio wave This product uses the 2.4 GHz frequency band. Other wireless devices may also use the same frequency, so please pay attention to the following to prevent radio waves from interfering with this device. In the frequency band used by this product, in addition to industrial, scientific, and medical equipment (such as microwave ovens), there are also radio stations for mobile object identification that require a factory production license, specific low-power radio stations that do not require a license and amateur radio stations, etc. (Hereinafter referred to as "other radio stations"). 1. Before using this product, please make sure that no "other radio stations" are operating nearby. 2. If this product causes radio wave interference to "other radio stations", please immediately change the place of use of this product or stop using the device. If this product is too close to other devices that use the 2.4 GHz frequency band, it may cause problems or malfunction due to radio wave interference. Communication may not be possible in the vicinity of a broadcasting radio station. If there are shelters between the linkable devices or due to the influence of the building structure, the transmission distance may be shortened. Interference shelters will absorb electromagnetic wave energy, attenuate the transmission signal, or shorten the transmission distance. The degree of influence depends on the material and thickness. According to the degree of possible interference, it can be divided into the following 4 categories. When installing, avoid "very high interference" shelters as much as possible: Low interference: such as wood, glass and many synthetic materials Moderate interference: such as water, bricks, marble High interference: such as plaster, cement Very high interference: such as metal About sensors The sensor responds to changes in brightness and temperature. For example, if it is installed in the following places, it may not work properly or malfunction. The transmit and receive sensitivity of the linkable wall lamp will vary with the use environment, the following conditions / locations must be considered before installing: Places with strong radio waves Places where pets such as dogs or cats will pass Objects that will shake due to wind, such as curtains Places with glass such as glass doors Near high-temperature objects such as heating Glass between the lights may cause poor linkage function, Places where wind blows (near windows, etc.) Close to other lighting equipment such as doors and fish tank PRODUCT "Linkable wall lights" are LED wall lamps that use RF (Radio Frequency) transmitting and receiving technology to communicate between lights. When the surrounding environment becomes dark, the motion sensors on the lights will activate. When someone is detected by the sensor the LED will light up and communicate to the other lights in the path to light up at the same time creating a safe lighting path. DIMENSIONSunit: mm (inch) Body Backplate CONTENTS Model No.: AP7000RF Light body Backplate Self-tapping wood screw Double-sided tape Manual ABS-plastic, PCBA Stainless steel SUS304 Steel Adhesive Paper Power source: 3*AA alkaline dry batteries (not included) 1 pc 1 pc 2 pcs 1 pc 1 pc SPECIFICATIONS LED type * quantity Color temperature Luminous flux Length of lighting Human body sensor Ambient light sensor Wireless transmission method Wireless transmission distance PIR sensing angle PIR sensing distance Power source Battery life Low battery indicator Weight Body (excluding battery) Backplate (excluding tape) SMD * 1 pc 3000K±500 (warm white) About 25 lumens About 15 seconds PIR (Passive InfraRed) motion sensor Light sensor RF (Radio Frequency) 2.4 GHz About 20m (65'), distance without shelter About 120° About 150cm (60") 3*AA batteries (not included) 12 months (at 8~10 activations/day) or 4,000 times When the battery capacity is low, the red warning light flashes every 3 seconds. About 68g (2.40 oz) About 15g (0.53 oz) MOTION SENSOR SENSING RANGE The range of the motion sensor is affected by the sensor orientation and installation height. The sensitivity of the sensor will also vary due to factors such as the brightness and temperature changes in the surrounding environment. In addition, the speed of the person approaching the sensor will have an effect on when the light will turn on. Factors that may affect the motion sensor function are: 1. Approach from directly in front of the motion sensor. 2. The temperature difference between the ambient and human body is small. (For example: high temperature in summer) 3. Body temperature is not easy to detect. (For example: wearing heavy clothes) Replace the battery if the following conditions occur: Red indicator keeps flashing LED light is bright but dim LED light does not light up Light-up time becomes shorter When replacing the batteries be certain to replace ALL the batteries with new batteries. If the lights are placed in an area where they are frequently turned on and off. The battery life will be shorter than advertised. The motion sensors respond to temperature changes in the sensing area causing the light to turn on. Therefore pets can activate the lights which can also have an effect on battery life. LIGHTING ZONE SETUP This product uses 2.4 GHz wireless communication transmission to link each device. The maximum transmission distance is about 20m (65ft). When the ambient light is dark, the device that detects the motion will send a signal to link all other devices * within 20m (65 ft), if no interference shelter and * set with the same lighting zone for activation. HOW TO SET 1. Press the "lighting zone button" on the back of the device within 3 seconds to change the color of the "lighting zone indicator". The reason for setting the lighting zone is to avoid that the lighting area has nothing to do with the direction of travel, so as to save battery power. This device can create up to 3 lighting zones. The color of the setting button can be divided into blue (factory setting), green and white. Devices set to the same color can communicate with each other. The lighting zone set by the user will be retained after the new battery is replaced- NO need to reset. The wireless transmission distance may be shortened due to different use environments such as shelters or building structures. 2. After setting the color, the selected color (light) will be on for 3 seconds and then flash 3 times, indicating that the setting is complete. INSTALLATION Please read the instruction carefully before use, and keep it in a safe place for reference. Do not place any objects between wall lights to avoid interference of wireless transmission. Since the ambient conditions of the mounting area will affect the function of the lights. Check to make sure there are no problems in the mounting area before use. When the backplate cannot be attached to the wall by mounting screws, the supplied double sided tape can be used. Please note that the mounting surface must be clean and smooth for best results. Do not apply to rough or peeling walls. The double sided tape has a strong adhesive on both sides. It is very easy to damage the wall when the light is removed. Please use caution during installation and removal as the responsibility for wall damage falls on the installer. TROUBLESHOOTING There are people in the sensing area of the light but the light will not turn on. LED Light will not turn off. There is no one in the sensing area of the motion sensor, but the light is on. 1. Are the lights installed in a bright area? 2. Are the batteries installed correctly? 3. Is the battery power low? 4. Is the room temperature very low? Or are the people wearing heavy clothing? 5. Is the person being still and not moving? 1. Is anyone in the sensing area? 2. Is the battery low? Is there a heat source or moving objects in the sensing area? 1. When the surroundings are bright, the motion sensor is in sleep mode. Wait until the surroundings become dark or move to a darker place for inspection. 2. Please confirm that the battery's positive (+) and negative (-) poles are installed in the correct direction. 3. Replace the battery. 4. The operating principle of the sensor is to respond to temperature changes caused by the movement of the human body, so it is not easy to detect temperature differences under these conditions. 5. If the person in the sensing area is not moving, they will not be detected by the sensor. 1. Leave the sensing area or keep still. 2. Replace the battery. Remove the heat source or move light also remove any moving objects in the sensing area. The specifications and appearance of this device may be changed without notice due to improvements. FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC ID: 2AZOB-AP7000RF Warning: Changes or modifications to this unit not expressly approved by the part esponsible for compliance could void the user's authority to operate the equipmentAcrobat Distiller 11.0 (Windows)