Owner's Manual for EasywaveUni models including: STH01 Temperature Humidity Sensor, STH01, Temperature Humidity Sensor, Humidity Sensor, Sensor
STH01 Temperature humidity sensor Format 55 A E F B1 G C PTx B2 D
EN STH01 Temperature humidity sensor Format 55 Model transmission LED Scope of delivery Transmission module, battery CR2032, mounting plate, cover frame, adhesive pad, operating instructions Intended use The radio sensor may only be used to measure the ambient temperature and humidity and to transmit these values to an ELDAT smart home server. The manufacturer shall not be liable for any damage caused by improper or non-intended use! Safety instructions Please read the operating instructions carefully before using the device! STH01EN5001A01 Technical details Frequency: 868.30MHz Radiated power: 0.41mW Modulation: FSK Coding: Easywave neo Range: free-field: approx. 150 m buildings: approx. 30 m Power supply: 1x 3 V-battery, CR2032 Current consumption: max. 20mA Standby current: approx. 1.1µA Measuring range humidity: 20% to 80%RH ±5 %RH Measuring range temperature: 0°C to +60°C ±1°C Measured value transmission: every 10 min or at button operation Operating temperature: -20°C to +60°C Dimensions (w/l/h): Cover Mounting plate Cover frame 55/55/9.0 mm 71/71/1.8mm 80/80/9.4mm Weight: 49g (incl. battery and cover frame) - Also read the operating instructions for the devices to be controlled! - Do not modify the devices! - Have faulty devices checked by the manu- facturer! - Keep the batteries away from children! Function The temperature humidity sensor STH01 measures the temperature and relative humidity (RH) cyclically and sends these values to a compatible ELDAT smart home server. After inserting the battery, the sensor is immediately ready for operation and the current measured values are transmitted via a radio telegram. The current values a re automatically transmitted every 10 minutes. The current values c an also be sent manually by pressing the front button. The transmission LED lights up briefly during each transmission. The sensor can be mounted in most cover frames with cut-out dimensions of 55x55mm. Start-Up 1. Screw or stick the mounting plate to the instal- lation site. Attention! Make sure there is no interference with the wireless connection. Do not mount the device in a distribution box, in metal casings, in direct proximity to large metal objects, on the floor or close to it. 2. Insert the battery (C) into the transmission module (B2). The positive pole has to be visible! 3. Place the cover frame (D) onto the mounting plate (E) and snap the transmission module (B) onto the catches (F) on top and bottom. The arrow on the sensor module has to point upwards. 4. Snap the rocker (A) onto the transmission module (B). Programming the transmission code To program the sensor into the Smarthome server, please follow the instructions given in the app. As soon as you are prompted to do so, press the rear learning button PTx to send the programming telegram. You can then press the front button (A) to transmit the current measured values. F A figure 1 G B2 PTx B1 C 32 C E D A Rocker B1 Transmission module front B2 Transmission module back PTx Learning button C Battery CR2032 D Cover frame *) E Mounting plate F Catches G Transmission LED *) If necessary, the cover frame can be re- placed with frames from other manufacturers with a cutout size of 55x55 mm. Battery check The transmitter STH01 has a battery check function, which checks the capacity of the battery during the transmission process. If the capacity of the battery is low, the transmission LED flashes every 10 minutes for 3 seconds and a data telegram is transmitted. Replace the battery as soon as possible. Replacing the battery 1. Lever off the transmission group. 2. Replace the battery. Only use batteries of the type CR2032. Make sure the polarity is correct. The positive pole has to be visible! 3. Place the transmission group back onto the catches. Note: The coding of the transmiter is preserved even if there is no voltage supply. You do not need to program the code into the receiver again after a battery change. Troubleshooting If the radio receiver does not react to the STH01: - Change the battery, if necessary. - Check that the wireless connection at the installation site is not impaired between the STH01 and the receiver. - Reprogram the transmission code into the receiver. - Other wireless devices using the same frequency or working in direct proximity may interfere with the device. General information Disposal Waste electronic equipment must not be disposed of with household waste! Dispose of the waste product via collection facilities for electronic scrap or via your specialist dealer. Dispose of used batteries in a recycling bin for batteries or via the specialist trade. Dispose of packaging material in the recycling bins for cardboard, paper and plastic. Warranty Within the statutory warranty period we undertake to rectify free of charge by repair or replacement any product defects arising from material or production faults. Any unauthorized tampering with, or modifications to, the product shall render this warranty null and void. Conformity Hereby, ELDAT EaS GmbH declares that the radio equipment type STH01 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.eldat.de Customer service If the device does not work properly despite proper handling or in case of damage, please contact the manufacturer or your retailer. ELDAT EaS GmbH Schmiedestraße 2 15745 Wildau Germany Phone: +49 3375 9037-310 Internet: www.eldat.de E-mail: info@eldat.de UM159946C_0924 ENAdobe PDF Library 17.0