AEROGOGO
GIGA PUMP Zetta 1024
User Guide
Please read this manual carefully before using.
Product Overview
This product is a portable smart air pump, suitable for the inflation of small car tires, motorcycle tires, bicycle tires, balls, swimming rings, and other inflatables. Before using this product to inflate, please note that the air pressure is required. The product could get hot after a long time.
⚠️ Keep this product out of the reach of children to avoid injury.
Product Instruction
Key components of the GIGA PUMP Zetta 1024:
- Schrader valve
- Air hose
- LED light
- LED screen
- Turn on/off button [power-symbol]
- "-" button
- Light on button [light-symbol]
- "+" button
- Mode button [mode-symbol]
- USB connector (at the bottom) [USB-C symbol]
- Charging port (at the bottom)
Product Diagram
The product features a Schrader valve (1) at one end, connected to the main body which houses the LED screen (4), LED light (3), and control buttons (5, 6, 7, 8, 9). The air hose (2) connects to the main body. The bottom of the device includes the USB connector (10) and charging port (11). The top view shows the button layout (5, 6, 7, 9) and the air hose connection (8).
The illustration in this manual is only for reference. Please refer to the practical scenario properly when using the product.
Accessories
The package includes the following accessories:
- Schrader valve adaptor *1
- Presta valve adaptor *1
- Plastic nozzle adaptor *1
- Ball needle adaptor *1
- Handle-type nozzle adaptor *1
- Type-C charging cable *1
Operating Guide
1. Turn on
Long-press the "turn on/off button" [power-symbol] to start working. If the pump stops working for 180 seconds, the LED screen will enter a sleeping state automatically.
2. The power display and charging
Power display
While using, the battery icon will light up and it represents the remaining battery capacity.
Charging
Please fully charge the product for the first time and apply a 5V 2A adapter to connect the charging cable. When charging, the battery icon will flash. When fully charged, the battery icon will remain on.
Tip: The pump cannot work while charging.
3. Use of air nozzle and air needle
- Schrader valve: Suitable for mountain bikes, electric bikes, motorcycles, and cars. Connect the “schrader valve” directly to the air pump.
- Presta valve: Suitable for road bikes and mountain bikes. Connect the "Presta valve" to the air pump hose and insert it into the inflation hole.
- Plastic nozzle: Suitable for small inflatable toys, yoga balls, etc. Connect the "Plastic nozzle" to the air pump hose and insert it into the inflation hole.
- Ball needle: Suitable for various kinds of balls, such as basketball, football, etc. Connect the "Ball needle" to the air pump hose and insert it into the inflation hole.
- Handle-type nozzle: Suitable for bicycles, mountain bikes, and some car tires. Connect the "Handle-type nozzle" to the air pump directly. To begin inflation, lift the handle and insert it into the valve, then press down the handle. Once inflation is complete, lift the handle again to finish the process.
4. Detection of air pressure
When the air pump is power-on and connected to the inflatables, the LED screen can display the current air pressure of the inflatables automatically.
5. Proper air pressure
To ensure safety and avoid potential dangers occurred by low-pressure or over-inflation, please inquire the required air pressure value of the inflatables by reading the instructions below or other products' user manual before using the air pump.
| Product category | Product type | Recommended pressure range |
|---|---|---|
| Bicycle | Folding bicycle tire | 45-50psi |
| 12, 14, 16 inch bicycle tire | 30-50psi | |
| 20, 22, 24 inch bicycle tire | 40-50psi | |
| 26, 27.5, 29 inch bicycle tire | 45-65psi | |
| 700c road bike open tire | 100-130psi | |
| 700c highway support lower tube tire | 100-130psi | |
| Motorcycle | Motorcycle tire | 1.8-3.0bar |
| Car | Small car tire | 2.2-2.8bar |
| Basketball | 7-9psi | |
| Football | 8-16psi | |
| Volleyball | 4-5psi | |
| Rugby | 12-14psi |
Tip: The data shown here is for reference only. Please refer to the actual product parameters. If the inflatable product is damaged caused by excessive pressure, the consequence is at your risk.
6. Preset inflation tire pressure value
Mode switch
Click the "Mode button" [mode-symbol] to switch the inflation mode and choose the right one. Long-press the “Mode button” to choose the unit of pressure, bar or psi.
| Mode | Preset pressure |
|---|---|
| Car | 2.5bar |
| Motorcycle | 2.5bar |
| Bicycle | 45psi |
| Basketball | 8psi |
| Default preset value | 35psi |
Tip: Adjustable range: 3-150psi.
Fine-tuning presets
After selecting the inflation mode, click "+" or "-" to adjust the pressure value. Long-press "+" or "-" to quickly adjust the pressure value. When adjusting the preset pressure value, the number flashes to indicate the target pressure adjustment status, and the long light digital indicates the current pressure value.
Multifunctional lighting
Turn on the light [light bulb icon]. Click to switch the lighting mode between white-light illumination and white emergency light.
7. Inflating
Start to inflate
Connect the air valve, set the pressure, and click the "turn on/off button" [power-symbol] to start inflation. The LED screen will display the current pressure value. It will generate 75-80dB noise during inflation. The product could get hot after a long time; avoid long-term contact with the hot air hose and the pump. Let it cool down before you touch it.
Stop inflation
When the air pressure reaches the preset pressure value, the product will automatically stop working. During the inflation process, you can also stop it by clicking the "turn on/off button" [power-symbol].
Special reminder
Please be careful when inflating balloons, toy balls, swimming rings, and other products that require lower pressure than the Zetta 1024 can preset. Please manually stop the air pump when the product is fully inflated.
Battery and battery life
At full power, when the ambient temperature is 25 ℃, the continuous working time without load is about 30 minutes. The endurance becomes worse when the pressure load becomes larger or the ambient temperature becomes lower.
8. Shutdown
In the power-on state, long-press the "turn on/off button" [power-symbol] to turn off the product.
Notes
- Before using this product to inflate, please note that the air pressure is required to avoid injury caused by over-inflation bursting.
- The product has a built-in non-removable lithium battery. It is forbidden to throw the product into fire or discard it everywhere.
- The lithium battery may cause fire, spontaneous combustion, or explosion due to overheating, impact, or water ingress.
- Please avoid putting it in a high-temperature environment such as inside a car where the air pump could be exposed to the sunlight directly.
- Do not bend or step on the inflation tube during inflation to keep the air flowing smoothly.
- When the product is working, please do not leave; pay attention at any time to avoid the air pressure from being too high due to the unpreset air pressure.
- The product should avoid moisture, heavy falls, water immersion, and mud or sand intrusion.
- There is a DC motor in the product; please do not put it near flammable liquids or gases.
- The storage temperature of the product should not be lower than -10 ℃ or higher than 45 ℃. Overheating or undercooling will shorten the product life and damage the internal battery.
- The battery could be damaged if left idle for a long time; it is recommended to charge it at least once every three months.
- It is forbidden for children to use; keep this product out of the reach of children to avoid injury.
- Before setting the inflation pressure value, please make sure that you have selected the correct measurement unit, otherwise it may lead to dangers such as explosion caused by high pressure.
Product Parameters
| Inflatable pressure range | 0.2~10.3bar/3~150psi |
|---|---|
| Product size | 65mmx65mmx198mm |
| Product weight | 740g |
| Working temperature | Charging: 0℃~45℃ Discharging: -10℃~45℃ |
| Storage temperature | -10℃~45℃ |
| Trachea size | 400 ± 20mm |
| Battery capacity | 12V-2600mAh |
| Working noise | 75dB |
| Input current | 5V ≡ 2A |
| Output current | 5V ≡ 2A |
| Charging interface | USB-Type-C |
| Charging time | Less than 4 hours |
| Air pressure gauge accuracy | ±1.5psi |
Common unit conversion: 1bar = 14.5psi, 1bar = 100kPa.
Troubleshooting
| Malfunction | Solution |
|---|---|
| Slow inflation | 1. Check if the power is sufficient. 2. Check if the air hose is leaking. 3. Check if the connection parts at both ends of the air hose are tight. |
| Cannot inflate when turning on | 1. Check if the power is sufficient. 2. Check if the current tire pressure is higher than expected. |
| Incorrect inflation mode | 1. Check if the scenario mode is correct. 2. Select the free mode without any icon lit, and the preset value can be adjusted within the measurable range of 3-150psi. |
| Normal inflation with screen display "0" | Balloons and other low-pressure inflatable products are not within the measurable range of the device. |
| The air pump has shut down automatically after screwing the valve adaptor | Try to long-press "turn on/off button" [power-symbol] to restart. |
| Air leakage when connecting the hose | Try to tighten the hose. |
| The color of the power indicator is different in the working and non-working state | This phenomenon is not a malfunction. In the working state, the battery discharges rapidly and the voltage decreases, resulting in inconsistency between the working and non-working indicators. |
Warranty
- Since the date of purchase, this product is entitled to seven days of replacement and one year warranty for failures caused by normal operation according to the manual. Improper product use and artificial damage are not covered by the warranty.
- For product replacement, the product needs to be packaged intactly, and the product appearance is without any trace or damage. Replace the same type of product with your purchase receipt and warranty card.
- The warranty card is only limited to non-human damages. The following conditions are not covered by the warranty:
- [checkbox] Any damage caused by force majeure.
- [checkbox] Products without stickers and serial numbers, and disassembled machines.
- [checkbox] The warranty period and warranty range are exceeded or the warranty card is not matched, altered, or lost.
- [checkbox] All artificial damage, including self-disassembly, accidental damage, and wear and tear, caused by high temperature, water ingress, breakage, wear, motor burnout occurred by high-voltage supply, etc.
