System Sensor RTS151KEY(A) Remote Test Station

Specifications

NOTE: RTS151KEY(A) replaces RTS451KEY.

NOTICE: This manual shall be left with the owner/user of this equipment.

NOTE: A test coil is required only for use with D2/DNR/DH400/DH500 models. For D2 models order part # DCOIL. For DH400/500 models order part #Coil.

General Information

The System Sensor RTS151KEY(A) is an automatic fire detector accessory designed to test remotely located duct and beam detectors. For 4-wire detectors, the RTS151KEY(A) features a multi-colored LED that alternates between steady green and red. Green indicates power and that the detector board is in place. Red indicates alarm. For 2-wire detectors, the LED will show red for alarm. Consult the detector installation instructions for additional information.

The National Fire Protection Association has published codes, standards, and recommended practices for the installation and use of this product. It is recommended that the installer be familiar with these requirements, with local codes, and any special requirements of the local authority having jurisdiction.

RTS151 Contents

• 1 RTS151KEY(A) remote test station
• 1 screw pack (2 mounting screws)
• 2 Keys

Operation

Test Function

Insert the key and turn clockwise to the "TEST" position. ▶️

Alarm Indication

With the key in the "TEST" position, some time will elapse (40 seconds maximum) depending on the detector type, before the alarm indicating LED will turn red.

Reset Function

Turn the key counterclockwise to the "RESET" position and hold. The LED should turn off. Then, turn the key back to the "NORMAL" position and remove. The RTS151KEY(A) is capable of resetting only certain models of detectors. Refer to the detector installation instructions for additional information. ⚙️

Wiring Instructions

Consult the appropriate detector installation instructions for the applicable wiring diagram. The RTS151KEY(A) mounts to a single gang box (2 1/2" minimum depth), or directly to the wall or ceiling.

In Canadian applications, the RTS151KEY(A) is intended to be located in the same room as the smoke detector and within 60 feet of the unit.

Diagrams

Figure 1: RTS151KEY(A)

A front view of the RTS151KEY(A) unit showing the key slot and the ALARM/OFF/RESET labels.

Figure 2: Wiring Diagram for RTS151KEY(A) to D4120 4-Wire Duct Smoke Detector

This diagram illustrates the wiring connections between the RTS151KEY(A) and a D4120 4-wire duct smoke detector. It shows connections for AUX OUT, FIELD INSTALLED JUMPER, ALARM, POWER, and RESET between the two devices. It notes that "Sup. contacts cannot be used if they are wired to control panel."

Figure 3: Wiring Diagram for RTS151KEY(A) to DNR 2-Wire Duct Smoke Detector with Remote Test Capable Head

This diagram shows the wiring for the RTS151KEY(A) to a DNR 2-wire duct smoke detector. Connections are detailed for TEST COIL, COMM, OUT, RA/RTS, and JUMPER between the RTS151KEY(A) and the detector. It also indicates a jumper setting on the RTS151KEY(A).

Figure 4: Wiring Diagram for RTS151KEY(A) to D2 2-Wire Duct Smoke Detector

This diagram presents two methods for wiring the RTS151KEY(A) to a D2 2-wire duct smoke detector. Method 1 shows AUX POWER located at the duct detector, and Method 2 shows AUX POWER located at the test station. Both methods detail connections for TEST COIL, IN, OUT, ALARM LED, RA, and RTS. It also mentions the use of a magnet test switch and the requirement for an accessory coil (DCOIL).

Figure 5: Wiring Diagram for RTS151KEY(A) to DH100ACDC 4-Wire Duct Smoke Detector

This diagram illustrates the wiring between the RTS151KEY(A) and a DH100ACDC 4-wire duct smoke detector. It shows connections for Alarm Signal, Aux. Power, Sup. N.O., Sup. COM, Power, and Test. It notes that "Sup. contacts cannot be used if they are wired to control panel."

Figure 6: Wiring Diagram for RTS151KEY(A) to DH100 2-Wire Duct Smoke Detector

This diagram details the wiring for the RTS151KEY(A) to a DH100 2-wire duct smoke detector. It shows connections for Test/Reset, Reset, RA, and V Out. It notes that terminal 6 of the RTS151KEY(A) is not used when wired to a 2-wire detector and that there is no connection for V Out.

Figure 7: Wiring Diagram for RTS151KEY(A) to DH400ACDC Duct Smoke Detector

This diagram shows the wiring connections between the RTS151KEY(A) and a DH400ACDC duct smoke detector. It includes connections for Alarm Signal, Aux. Power, Sup. N.O., Sup. COM, Power, Reset, and Test. It also notes that "Sup. contacts cannot be used if they are wired to control panel."

Figure 8: Wiring Diagram for RTS151KEY(A) to BEAM1224/BEAM1224T Smoke Detector

This diagram illustrates the wiring of the RTS151KEY(A) to a BEAM1224/BEAM1224T smoke detector. Connections are shown for REMOTE ALARM OUT, AUX (-), RESET INPUT, REMOTE TROUBLE OUTPUT, and TEST INPUT. It also mentions that the RTS151KEY(A) can be used with intelligent beam detector products and advises consulting the intelligent beam detector manual for additional instructions.

Three-Year Limited Warranty

System Sensor warrants its enclosed product to be free from defects in materials and workmanship under normal use and service for a period of three years from the date of manufacture. System Sensor makes no other express warranty for the enclosed product. No agent, representative, dealer, or employee of the Company has the authority to increase or alter the obligations or limitations of this Warranty. The Company's obligation under this Warranty shall be limited to the replacement of any part of the product which is found to be defective in materials or workmanship under normal use and service during the three-year period commencing with the date of manufacture. After phoning System Sensor's toll-free number 800-SENSOR2 (736-7672) for a Return Authorization number, send defective units postage prepaid to: Honeywell, 12220 Rojas Drive, Suite 700, El Paso TX 79936, USA. Please include a note describing the malfunction and suspected cause of failure. The Company shall not be obligated to replace units which are found to be defective because of damage, unreasonable use, modifications, or alterations occurring after the date of manufacture. In no case shall the Company be liable for any consequential or incidental damages for breach of this or any other Warranty, expressed or implied, whatsoever, even if the loss or damage is caused by the Company's negligence or fault. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.