User Manual for Imou models including: Smart Robot Vacuum Cleaner, Robot Vacuum, Robot Vacuum Cleaner, Vacuum Cleaner
Then, start the unit after removing it from the danger area. Check if the main brush is stuck. Check if the side brush is stuck. Check if the main wheel is ...
May 27, 2025 — Plastic bags can be dangerous. Keep them away from infants and children to avoid the risk of suffocation. This product is only meant to clean floors in a ...
File Info : application/pdf, 19 Pages, 5.86MB
DocumentDocumentUserManual V1.0.1 Smart Robot Vacuum Cleaner Series Safety Precautions Usage Restrictions Plasticbagscanbe dangerous.Keepthemawayfrominfantsandchildrentoavoidtheriskofsuffocation. This product is only meant to clean floors in a home environment. Do not use it outdoors (such as in an open balcony), on other non-floor surfaces (such as sofas), or in commercial or industrial settings. Do not use the product in a suspended environment (such as duplex buildings, open balconies, or on top of furniture) without guard rails. Do not use the product in temperatures higher than 40°C (104 °F) or lower than 0°C (32°F). Do not use the product if there is liquid or viscous substances on the floor. Ensure that cables are kept off the floor before using the device to prevent cables from being dragged around when the device is working. Keep all fragile and miscellaneous items (such as vases or plastic bags) that are not on the floor to avoid obstruction of or collision with the device while it is working, which may result in damage of valuable items. Do not allow people with impaired physical, sensing or mental abilities, or people with insufficient experience and knowledge (including children) to use this product without guidance or supervision. Do not allow infants or children to use this product as a toy. Do not place the main brush cleaning tool within reach of children. Do not allow any body parts of humans or animals, including hair, fur, fingers, etc., to come close to the vacuum inlet of the device when the device is working. Do not use the product to clean flammable objects (such as lit cigarette butts). Do not use the device to vacuum hard or sharp objects (such as waste materials from renovation, glass, or nails). Do not use the cover of the laser range sensor, the top cover of the device, or the collision buffer device as carry handles for transporting the robot. Before cleaning and maintaining the device and charging dock, turn the device off and unplug it from the socket to disconnect the power supply. Do not submerge the device or the charging dock in water or rinse them with water to clean them. Do not use a wet cloth or any liquid to wipe any part of this product. Do not use the mop module in a carpeted environment. Follow the instructions in the manual when using this product. The user is responsible for any loss or damage caused by improper use. Battery and Charging Burningthedeviceisprohibitedeveniftheproducthasbeenseverelydamaged,asdoingsomaycauseexplosions. Donotuseanythird-partybatteries,chargers,orchargingdocks. Donotdisassemble, repair, ormodifybatteriesandchargingdocks. EN | 01 Battery and Charging Do not place the device near heat sources, such as radiators. Donotwipeorcleanthechargingdockclipswithadampclothorwethands. Do not dispose of batteries with your regular trash. Batteries should be disposed of by professional recycling agencies. If the power cord is damaged, it must be replaced by professionals from the manufacturer, the manufacturer's service department, or a similar department to avoid danger. If the product must be transported, ensure the device is turned off. It is recommended that you use the original box packaging to transport the product. Do not pour water into the device or submerge it in water. If you are not using the device for a while, charge it fully, turn off the device, and place it in a cool, dry area. Charge the device at least once every three months to avoid damage to the battery. Use proper tools when removing the battery. First, remove the screws from the bottom cover. Then, open the bottom cover and unplug the battery from the terminal. Finally, remove the battery from the battery holder. The battery must be removed from the device before discarding the device. The device must be powered off before removing the battery. Class 1 laser product. The laser radar in this product conforms to the GB 7247.1-2012/IEC 60825-1:2014 safety standards for Class 1 lasers, and will not produce laser radiation harmful to the human body. EN | 02 PackageContents i Diagrams of products, accessories, user interfaces, and other items in the manual are schematic diagrams and are for reference only. The actual product may differ slightly from diagrams in the manual due to product updates and upgrades. The actual product shall prevail in case of any discrepancies. Accessories Installed on the Robot Main Brush Main Brush Cover Side Brush Robot Power Adapter Side Brush Cleaning Knife (1 pc) Two-in-one Water Tank Charging Dock Mop Holder Washable Mop Cloth EN | 03 Overview Robot Top View Infrared Sensor Collision Buffer Board Recharge Button/ Indicator Light Power Button/ Indicator Light Robot Bottom View Laser Radar Bumper Strips Obstacle Avoidance Sensor Mop Cloth Module Main Brush Cover Main Brush Main Wheel Cliff Sensor Side Brush Omnidirectional Wheel Cliff Sensor EN | 04 Charging Plate Dust Box Release Button Dust Box Charging Dock Force Shutdown Button Wallfollowing Sensor Indicator Lentille infrarouge Charging Contacts Filter Cartridge Filter Protective Plate Release Latch Protective Plate Power Adapter Port EN | 05 LED Indicator Patterns White LED Status White Red Orange Solid on Breath Flashes slowly Flashes fast to off Flashes fast Solid on Flashes fast Flashes slowly Breath Orange Flashes fast Flashes fast to off Device Status The robot is standby / cleaning The robot is charging / turning on Cleaning is paused The robot is turning off The robot malfunctions The robot is recharging Connecting to the Wi-Fi network Waiting for Wi-Fi connection Low battery level OTA updating / changing vioce prompt language Reset to the factory mode EN | 06 Notes Before Use Tidy up the plugs and power cords that could entangle the robot. Fold the carpet tasseled edges under to improve the cleaning efficiency. Preparations Before Use Imou Life App To enjoy all available features, it is recommended to control the device on the Imou Life app. Please make sure that your mobile phone is connected to a 2.4 Ghz Wi-Fi network. Ensure that the Wi-Fi password does not include " " or spaces. Scan the QR code below or search for the "Imou Life" app in the App Store to download and install the app. After completing the app installation, please open the app, click on "+" in the top right corner of the home page, and scan the QR code on the bottom of the device or on the package box. Follow the directions to add the device. Put the weight scales out of the area Do not use the robot on wet surfaces to be cleaned. or floor with standing water. Put away the mops or pieces of paper on the floor. Do not start cleaning from the edge of stairs or a drop to avoid the robot from falling over. Restoring to Factory Settings If your robot cannot connect to the app successfully, reset the Wi-Fi and add the device again. Press and hold and simultaneously for 5 seconds. When indicator light flashes white and indicator light flashes orange to off, the device will restart within 30 seconds. Then you will hear the voice prompt "Wi-Fi has been reset" and the device will be waiting for a network connection. Then follow the directions in the app to add the device. EN | 07 Installation and Use/Preparation 1 Remove protective strips Place the robot on a level ground and remove the protective materials. 3 Charging the robot Press and hold for 3 seconds to start the robot. Then, press to recall the robot to the dock for charging. The robot will enter standby mode after it is fully charged. 2 Install the charging dock EN | 08 Installation and Use/Cleaning 1 Cleaning Tap to start Auto cleaning; Press and hold for 3 seconds to start Spot cleaning. 2 Pause cleaning When the robot is cleaning, tap or to pause the cleaning. 4 Standby/Sleep Mode When the robot is fully charged and securely docked, press and hold the button for 3 seconds to enable low-power standby mode. The mode will be automatically disabled if the robot's battery level drops below 90% or if it begins a cleaning task. 5 Turn off When the robot is stationary, press and hold for 3 seconds to turn the device off. The power indicator light will fast flash white for 5 seconds before it turns off. 3 Automatic recharge/Manual recharge The robot will automatically return to the dock to charge if there is insufficient power while cleaning. The robot will also return to the dock to charge after cleaning is completed. When the robot is cleaning, press or to pause the robot, and then press to recall the robot to the dust collection charging dock for charging. The robot cannot be powered off and cannot enter sleep mode while charging. EN | 09 Installation and Use/Mopping 1 Remove the two-in-one water tank Press the Dust Box Release button to remove the two-in-one water tank. 3 Install the mop holder EN EN 2 Add water i It is recommended that you use purified water. 4 Mop Press Press to start Auto mopping; for 3 seconds to start Spot mopping. EN | 10 Regular Maintenance To keep the device at best performance, please refer to the following maintenance frequencies. Please use a soft and clean cloth to wipe the parts, and avoid using any detergents or cleaning sprays. Parts Cliff Sensor Infrared Sensor Wall-following Sensor Laser Radar Sensor Charging Plates Main Brush Side Brushes Mopping Cloth Dust Box Filter Maintenance Once per month Once per month Once per month Once per month Once per month After each cleaning When necessary After each mopping When necessary Once per month Replacement / / / / / After 240 hours of cleaning After 150 hours of cleaning After 180 hours of cleaning / After 150 hours of cleaning Clean Sensors Wall-following Sensor Cliff Sensor Infrared Sensor Charging Plate Infrared Lens Charging Contacts EN | 11 Clean the Main Brush i 1 Press the catch on the cover of the main brush. Then, remove the main brush cover and the main brush. Clean/Replace the Side Brush 1 Remove the screws of the side brush with a screwdriver. Then, remove the side brush. 2 Cut entangled hairs and fur on the main brush using the small cleaning knife. Use the cleaning brush on the other end of the cleaning knife to clean the main brush. 3 Reinstall the main brush and main brush cover. Press to fasten the catch. 2 Replace the side brush after cleaning, or install a new side brush. EN | 12 Cleaning the Two-in-one Water Tank 1 Press and hold the two-in-one water tank release button, and pull the water tank out. 3 Remove the filter cartridge. 5 Use the cleaning brush to clean the filter and any debris on the filter cartridge. 2 Pull the dust box catch to open the dust box. 4 Remove the filter. 2 6 Use a dry cloth to clean the dust box. After the cleaning, wipe the dust box and dry the cloth. EN | 13 7 Open the water tank cover and add an appropriate amount of water. It is recommended that you use purified water. 8 Turn the two-in-one water tank upside down, and remove the mop cloth for replacement or cleaning. Mopping will be less effective if the mop cloth is too dirty. Do clean the mop cloth in a timely manner. Always remove the mop cloth, clean it, and wring it dry before reinstalling it and using it. Do not install it on the two-in-one water tank to clean it, or the reverse flow of dirty water will clog the filter element. After cleaning the inside of the dust box, ensure that the inside of the dust box is dry and free from water stains. Otherwise, the dust collection charging dock will be damaged. If there are water stains on the filter and filter cartridge, ensure that they are dry before use. Otherwise, the dust collection charging dock will be damaged. Battery Maintenance The robot has an internal high-performance lithium-ion battery pack. Keep the device charged on a day-to-day basis to maintain battery performance. If you are not using the device for a while, turn it off before storing it. Charge the device at least once every three months to avoid damage to the battery. It is recommended to change the battery after approximately 800 hours of cleaning to ensure an optimal performance. EN | 14 Troubleshooting When an abnormality occurs while the device is running, the power indicator light will flash red quickly. There will be voice prompts for some abnoirmalities. Refer to the table below for possible solutions. Voice Prompts/ Fault Description Possible Reason Solutions Check if the radar is stuck Laser radar is blocked or stuck Remove obstacles, or move the device to a flat and open area, and restart it. Check if the bumpers are stuck Collision sensor is stuck Clean and remove any foreign debris around the bumpers, or move the device. Clean the cliff sensor. Then, start the unit after removing it from the danger area. Cliff sensor is triggered after starting the device Remove and clean the cliff sensor. Then, move it to a flat and open area before starting it. Check if the main brush is stuck Main brush is stuck Clean the main brush or move the device. Check if the side brush is stuck Side brush is stuck Clean the side brush or move the device. Check if the main wheel is stuck Main wheel is stuck Clean the main wheel or remove the device. Put back the water tank before restarting the device The battery is insufficient. Start recalling the device to the dock for charging. Two-in-one water tank is removed Battery is insufficient while cleaning Fan is abnormal Fan is abnormal Wipe the wall-following sensor on the right side Pressure on the top cover of the laser radar Wall-following sensor is abnormal Top cover on the radar is stuck Install back the two-in-one water tank and filter while ensuring that they are installed in the right place. The battery is insufficient. Charge the device before use. Ensure that the air ducts, filter, and other relevant parts of the device are dry and free from water stains before attempting to turn off and restart the device. Wipe clean the wall-following sensor. The laser radar is stuck or under pressure. Move the device to a new position and restart it. EN | 15 Troubleshooting Voice Prompts/ Fault Description Battery is damaged or has not been properly installed Unable to turn on Possible Reason Battery is abnormal while charging Battery level is low or ambient temperature is abnormal. Unable to charge the device 1. The charging dock unelectrified. 2. Dirty charging sensor. 3. Poor contact with the charging sensor. Unable to return to charging dock to charge. Unable to locate The charging dock is blocked or too far away. the dust collection charging dock. Errors occur while cleaning The main/side brush, or the main brush is entangled with foreign objects. Decreased cleaning ability or dust falling out of the device The dust box is full, the filter is blocked, or the main brush is entangled. Unavailable scheduled cleaning mode The battery is insufficient. Unable to connect to the app The Wi-Fi network is abnormal, the Wi-Fi password is wrong, or the app is abnormal. Solutions The battery temperature is too high or too low. Wait until the battery temperature is normal before using it. The battery is insufficient. Charge the device before use. If the ambient temperature is too low (below 0°C) or too high (above 50°C), use the device in temperatures between 0°C and 40°C. 1. Ensure that there is power flowing to the power cord of the charging dock. 2. Clean the charging plates of the device and the charging sensor head of the charging dock on a regular basis. 3. Exclude the possibility of poor contact caused by the side brush or other foreign objects. Try manually helping the robot back to the charging dock. Place the dust collection charging dock in an open space. Place the device near the charging dock and try again. Clean the robot from foreign objects. Clean the dust box, filter, and main brush in a timely manner. The device will start the scheduled cleaning mode only when the remaining battery is more than 15%. So, keep the device charged all day. Ensure that the device is in an area with good Wi-Fi coverage. Re-enter the Wi-Fi password or reset the robot. Update the app and try again. EN | 16 Troubleshooting Voice Prompts/ Fault Description No or little water discharged from the mop module Too much water discharged from the mop module Insufficient battery during cleaning; device recharged but does not resume cleaning Does not return to the charging dock after area cleaning or after being moved. Possible Reason Solutions The water tank is out of water, the mop cloth is too dirty, or the mop holder is not installed in the right place. The cover of the water tank is not put in place or the water discharge is set to maximum. The device is in "Do Not Disturb" mode or manually recharged to end the cleaning cycle. Check if there is water in the tank. Wash the mop cloth. Install the mop cloth correctly according to the manuals. Check if the drain hole is clogged with foreign objects and pay attention to adding clean water without impurities. Ensure that the cover of the water tank is installed in the right place. Adjust the right amount of water in the app. Fill the water tank and let it sit for a while to check if there is any breakage or leakage. Check on the app to ensure that the device is not in "Do Not Disturb" mode. Cleaning will not resume in this mode. The robot will not resume cleaning if you manually charge the unit or manually place the unit back in the dust collection charging dock. The device will regenerate the map after area cleaning or being removed The device regenerates the map or the charging dock far away. If the charging dock is too far away, the device may not be able to is too far away. automatically return to the dock for charging, and you need to manually put the device back to the dock for charging. EN | 17Corel PDF Engine Version 16.1.0.843 CorelDRAW X6