User Manual for JONATHAN models including: JYL1504 Hugo 3 Light 25 Wide LED Vanity Light Set, JYL1504, Hugo 3 Light 25 Wide LED Vanity Light Set, 25 Wide LED Vanity Light Set, Vanity Light Set, Light Set
JONATHAN Y Lighting JYL1504B Oil Rubbed Bronze / Gold Painting Hugo 3 Light 25" Wide LED Vanity Light Set with Towel Bar, Towel Ring, Robe Hook, and Toilet Paper Holder - LightingDirect.com
WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. CARE AND MAINTENANCE To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully. NOTICE& IMPORTANT SAFETY INSTRUCTIONS * Please make sure that you have all parts indicated before you begin assembly of this item * This item should be assembled on a soft surface to prevent scratching the finish during assembly * To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation *The external flexible cable or cord of this luminaire cannot be replaced If the cord is damaged, the luminaire shall be destroyed Part List and Hardware List PIECE DESCRIPTION A wire connector B mounting plate C ground screw PICTURE QUANTITY PIECE 3X K 1X L 1X M DESCRIPTION short mounting bracket long mounting bracket wood screw D machine screw 2X N screw E Round nut 2X O hex kry F lamp body 1X P towel ring G glass 3X Q robe hook H screwed ball 9X R toilet paper holder I bulb 3X S body of towel bar J wall anchors 10X T towel bar PICTURE 1/3 QUANTITY 2X 3X 10X 5X 1X 1X 1X 1X 2X 1X Model#: JYL1504 Product Dimensions: 24.5"W X6.75"EX 11.75"H PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes. If there are any questions relating to defects, missing parts, assembly issues, replacements, or device connectivity issues, please send a detailed email to cs@jonathany.com 1. Separate the mounting plate (B) from the lamp body (F) by removing the Round nut (E) anti-clockwise. then fix the mounting plate (B) to the outlet box with machine screw (D). 2. Make wire connections, with wire connectors(A), following the reference chart listed below. Connect, Hot, Black or Red Outlet Supply Wire to: Black * Parallel Cord (round & smooth) Clear, Brown, Gold or Black without Tracer stripes) (colored Connect, Neutral, White Outlet Supply Wire to: White * Parallel Cord (square & ridged) Clear, Brown, Gold or Black with Tracer (colored stripes) Insulated Wire (not green) with copper metal conductor Insulated Wire (not green) with Silver metal conductor. *Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. ) Grounding Instructions: a) For installation in the United States: Wrap ground wire from outlet box around green ground screw (C) on mounting plate, no less than 2" from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector. b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting plate. Tighten ground screw. 3. Orient the ceiling canopy of the lamp body (F) so that the mounting screws protruding from the mounting plate (B) go into the holes in the canopy of the lamp body (F), then secure it with the provided Round nut (E). 4. Install bulb (I). Be sure to use light bulb(s) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs. 5. Place the glass (G) onto the socket, then fasten it by screwed ball (H) PLEASE USE ON/OFF TYPE"A" BULB MAX 40-WATT OR LED BULB MAX 9 -WATT THERE ARE 3PCS 4WATT LED BULB IN THE BOX ENJOY YOUR LAMP 2/3 Installing the towel ring 1. Determine the location for the towel ring (P). Using the short mounting bracket (K) as a template, mark the location of the holes for the wall anchors (J). Drill the appropriate size holes for the wall anchors (J). (the holes should be slightly smaller than the size of the wall anchors (J). ). The wall anchors (J) are then punched into the drilled holes, And allowing for the wood screws (M) to protrude through the hole on short mounting bracket (K), then screw the wood screw (M) to the wall anchors (J). 2. Place the towel ring (P) over the short mounting bracker (K) and use the hex key (O) to secure it in place by using screw (N). Installing the robe hook 1. Determine the location for the robe hook (Q). Using the short mounting bracket (K) as a template, mark the location of the holes for the wall anchors (J). Drill the appropriate size holes for the wall anchors (J). (the holes should be slightly smaller than the size of the wall anchors (J). ). The wall anchors (J) are then punched into the drilled holes, And allowing for the wood screws (M) to protrude through the hole on short mounting bracket (K), then screw the wood screw (M) to the wall anchors (J). 2. Place the robe hook (Q) over the short mounting bracker (K) and use the hex key (O) to secure it in place by using screw (N). Installing the toilet paper holder 1. Determine the location for the toilet paper holder (R). Using the long mounting bracket (L) as a template, mark the location of the holes for the wall anchors (J). Drill the appropriate size holes for the wall anchors (J). (the holes should be slightly smaller than the size of the wall anchors (J). ). The wall anchors (J) are then punched into the drilled holes, And allowing for the wood screws (M) to protrude through the hole on long mounting bracket (L), then screw the wood screw (M) to the wall anchors (J). 2. Place the toilet paper holder (R) over thelong mounting bracker (L) and use the hex key (O) to secure it in place by using screw (N). NOTE: The toilet paper holder Can be installed in left and right instal. Installing the towel bar 1. Place the towel bar (T) to the body of towel bar (S). 2. Determine the location for the body of towel bar (S). Using the long mounting bracket (L) as a template, mark the location of the holes for the wall anchors (J). Drill the appropriate size holes for the wall anchors (J). (the holes should be slightly smaller than the size of the wall anchors (J). ). The wall anchors (J) are then punched into the drilled holes, And allowing for the wood screws (M) to protrude through the hole on long mounting bracket (L), then screw the wood screw (M) to the wall anchors (J). 3. Place the body of towel bar (S) over thelong mounting bracker (L) and use the hex key (O) to secure it in place by using screw (N). 3/3WPS 表格