the Smart Air™ Connect Purifier

Breville Recommends Safety First

At Breville, safety is paramount. Breville designs and manufactures consumer products with the safety of the user as the highest priority. Users are asked to exercise a degree of care and adhere to the following precautions.

Specifications

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE

• Remove and safely discard any packaging material and promotional labels before using the air purifier and filter for the first time.
• To eliminate a choking hazard for young children, remove and safely discard the protective cover fitted to the power plug of this air purifier.
• When unpacking the air purifier, check to see all listed items are present before discarding the packaging.
• This air purifier is intended for household use only, not for commercial or industrial use.
• Do not use outdoors.
• Always ensure the air purifier is properly assembled before use, following the instructions in this book.
• Do not place the air purifier near the edge of a bench or table during operation. Ensure the surface is level, clean, and free of water.
• Keep the power cord out of heavy traffic areas. To avoid fire hazard, never put the cord under rugs, near heat registers, radiators, stoves, or heaters.
• To protect against electrical hazards, do not immerse the unit in water or other liquids. Do not use the air purifier in the immediate surroundings of a bath, shower, or swimming pool.
• Children should be supervised to ensure they do not play with the air purifier.
• Always turn off and unplug the air purifier before moving, opening the grill, changing filters, cleaning, or when the unit is not in use.
• Do not unplug the air purifier by pulling on the power cord; always unplug using the power plug.
• Never insert fingers, pencils, or any other objects through the guards when the power plug is connected, especially while the air purifier is switched on.
• Do not run the power cord under carpeting or cover it with rugs or runners. Arrange the power cord away from traffic areas where it will not be tripped over.
• Do not route the power cord under furniture or appliances.
• Do not operate the air purifier with a damaged power cord or plug, or if the unit has been dropped or damaged in any manner. Take the unit to the nearest Breville service centre for examination, electrical, or mechanical adjustment or repair.
• Do not use the air purifier with an external timer, programmer, or any other device that switches the unit on automatically, as this may create a fire risk if the unit is covered or positioned incorrectly.
• Do not place anything on top of the air purifier when assembled, in use, or stored.
• Never block the air openings, grills/outlets, or place on a soft surface like a bed or sofa, as this could cause the unit to tip over, blocking the air inlet or outlet opening.
• Do not attempt to repair or adjust any electrical or mechanical functions on this unit, as doing so will void the warranty. The inside of the unit contains no user-serviceable parts other than the filter. All servicing should be performed by qualified personnel only.
• This air purifier contains a UV-C emitter. Unintended use or damage to the housing may result in the escape of dangerous UV-C light radiation, which can cause harm to eyes and skin even in small doses.
• Keep the air purifier and dust filters clean. Follow the cleaning instructions provided in this book.

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES

• Fully unwind the power cord before use.
• Connect only to a 230V or 240V power outlet.
• Do not let the power cord hang over the edge of a bench or table, touch hot surfaces, or become knotted.
• To protect against electric shock, do not immerse the power cord, power plug, or appliance in water or any other liquid, or allow moisture to come into contact with the part, unless recommended in the cleaning instructions.
• The appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use by a person responsible for their safety.
• Children should be supervised to ensure they do not play with the appliance.
• It is recommended to regularly inspect the appliance. To avoid a hazard, do not use the appliance if the power cord, power plug, or appliance becomes damaged in any way. Return the entire appliance to the nearest authorized Breville Service Centre for examination and/or repair.
• Any maintenance other than cleaning should be performed at an authorized Breville Service Centre.
• This appliance is for household use only. Do not use this appliance for anything other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors. Misuse may cause injury.
• The installation of a residual current device (safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance. Consult an electrician for professional advice.
• During electrical storms, disconnect the appliance from the power source at the wall socket to prevent electrical surges that may arise during the storm and which may inadvertently cause damage to the appliance and its electronic componentry.
• Always turn the appliance to the off position, switch off at the power outlet, and unplug at the power outlet when the appliance is not in use.
• Before cleaning, always turn the appliance to the off position, switch off at the power outlet, unplug at the power outlet, and remove the power cord (if detachable) from the appliance. Allow all parts to cool.
• Do not place this appliance on or near a heat source, such as a hot plate, oven, or heaters.
• Position the appliance at a minimum distance of 20cm away from walls, curtains, and other heat or steam-sensitive materials. Provide adequate space above and on all sides for air circulation.

FOR HOUSEHOLD USE ONLY

SAVE THESE INSTRUCTIONS

Components

The air purifier consists of the following parts:

• A. Air Outlet: The top opening where purified air is expelled.
• B. Control Panel: Located on the top of the unit for user interaction.
• C. Main Housing Body: The primary structure of the air purifier.
• D. Air Quality Sensor: Detects the level of pollutants in the air.
• E. Air Inlet: The lower section where air is drawn into the unit.
• F. Microbe Shield™ Light and Light Guard: Emits UV-C light to neutralize germs.
• G. 3-Layer Filter: The internal filter system for air purification.
• H. Base Plate: The bottom part of the unit.
• I. Locking Knob: Secures the base plate.
• NOT PICTURED: Power Cord.

Control Panel

The control panel allows users to operate the air purifier:

• A. Power On/Off: Turns the unit on and off.
• B. Microbe Shield™/Night Mode/Reset Filter: Cycles through Microbe Shield™ mode, Night Mode, and resets the filter indicator.
• C. Timer: Sets operating intervals (2, 4, or 8 hours).
• D. Fan Speed: Adjusts the fan speed (Low, Medium, High, Turbo).
• E. Air Quality Sensor Light: Indicates the current air quality with different colors (Blue: Very Good, Yellow: Good, Orange: Fair, Red: Poor).

Wi-Fi Pairing: Hold the [plus] and [wifi-symbol] buttons for 5 seconds to activate Wi-Fi pairing.

Features

The Breville Smart Air™ Connect Purifier enhances indoor air quality through four distinct levels of protection:

1. A Pre-Filter: Captures larger airborne particles like human hair, pet dander, and dust particles.
2. A True HEPA Filter: Traps up to 99.97% of allergens and airborne contaminants down to 0.3 microns, including dust, mould spores, plant spores, and pollen.
3. An Activated Carbon Membrane: Assists in capturing dust, smoke, and pollen, while also neutralizing odors and eliminating fumes from household products and volatile organic compounds (VOCs).
4. Microbe Shield™ Technology: Utilizes shortwave UV-C light to target germs and bacteria in the incoming air before releasing purified air. This function can be turned on or off as needed.

Assembly

BEFORE FIRST USE

• Remove and safely discard all packaging material and promotional labels attached to the air purifier and filter.
• Remove the filter from the air purifier (see REPLACING THE FILTER on page 13) and take it out of its plastic bag. Re-insert the filter into the air purifier.
• Select a flat and level location for the air purifier.
• For proper airflow, position the unit at least 20cm from any wall or furniture.
• Ensure the air inlet and outlets are not blocked before use.
• Plug the power plug into a 230V or 240V power outlet and turn on the power outlet.

IMPORTANT: When moving the air purifier, always lift the unit using two hands and set it down gently on a flat and level surface.

Functions

OPERATING YOUR AIR PURIFIER

1. Press the POWER button to turn on the unit. The On/Wi-Fi reset light will illuminate.
2. The air quality sensor light will illuminate, typically starting with blue, and may change color as it senses the air quality.
3. Adjust operation using the following controls:

SensAir™ LIVE PURITY CONTROL

• The Breville Smart Air™ Connect Purifier has a built-in air quality sensor that detects changes in the surrounding air.
• The SensAir™ indicator light around the control panel changes color based on air quality:
  • Grade 1 (Very Good): Blue light
  • Grade 2 (Good): Yellow light
  • Grade 3 (Fair): Orange light
  • Grade 4 (Poor): Red light

Microbe Shield™/NIGHT MODE/RESET FILTER

This button controls Microbe Shield™, Night Mode, and the Filter Reset function. Pressing it cycles through these modes.

• Microbe Shield™: Press the button until the Microbe Shield™ indicator light illuminates to activate it. To turn it off, press again.
• Night Mode: Press the button until the night indicator light blinks. After 10 blinks, all control panel lights turn off, and the fan speed defaults to Low. Press any button to exit Night Mode.
• Filter Reset: When the filter reset light blinks continuously, the filter needs replacement. After replacing the filter, press and hold the Microbe Shield™/Night Mode/Filter Reset button for 5 seconds to reset the indicator.

FAN SPEED/TURBO MODE

The air purifier will resume its last programmed setting after being turned off, even if unplugged. If the last setting was Night Mode, the Night indicator light will blink upon restart.

• Press the FAN SPEED button repeatedly until the desired speed is illuminated on the control panel.
• Available speeds: Low, Medium, High, and Turbo.
• Turbo mode is indicated when all three speed lights are illuminated simultaneously.

NOTE: The unit may take a few seconds to adjust fan speed.

TIMER

• The air purifier can be set to operate for timed intervals of 2, 4, or 8 hours, stopping automatically when the selected time elapses.
• If no timer is set, the air purifier operates continuously until manually switched off.
• Press the TIMER button repeatedly until the desired interval hours are illuminated.
• For continuous operation, press the TIMER button until no timer lights are illuminated.

AUTO MODE

• In Auto mode, the air purifier automatically adjusts fan speed based on sensor readings.
• To set Auto mode, press and hold the POWER button until the Auto indicator light illuminates.
• To turn off Auto mode, press the POWER button or Fan Speed button; the Auto indicator light will extinguish.

IMPORTANT: Turning the unit On and Off requires cycling through Auto mode.

FILTER RESET

The Filter reset light blinking continuously indicates the filter needs replacement. Replace the filter as per instructions. To reset the indicator after replacement, press and hold the Microbe Shield™/Night Mode/Filter Reset button for 5 seconds.

The built-in timer for filter reset is 4,320 operating hours.

NOTE: For best performance, clean the filter at least monthly as per the Care, Cleaning & Storage section.

Wi-Fi Connectivity

The Breville Smart Air™ Connect Purifier can be operated remotely using a home Wi-Fi connection and the Breville Home Connect™ app, available on Google Play Store or Apple App Store.

CONNECT YOUR PURIFIER TO WI-FI:

1. Ensure your mobile device is connected to a home Wi-Fi network.
2. Turn on the purifier via the control panel. The Wi-Fi symbol [wifi-symbol] will flash rapidly on the display. The purifier is now ready to connect.
3. Log into your Breville Home Connect™ app account and navigate to the "Home" page. Touch 'Add Device' or the [plus] symbol in the top right corner. Follow the in-app prompts.
4. If connection is successful, the purifier will appear in the app, and the Wi-Fi symbol on the purifier will illuminate.
5. If connection fails, touch and hold the [wifi-symbol] and [power] buttons together for 5 seconds until the Wi-Fi symbol flashes slowly. Follow the in-app prompts to connect in a different mode.

NOTE: The Breville Home Connect™ app is compatible with mobile phones running Android 5.0 or later and iOS devices 9.0 or later.

NOTE: To control the purifier via the app, it must be plugged into an active power outlet.

Care, Cleaning & Storage

The air purifier and filter should be cleaned at least once every month. Ensure the unit is switched off, disconnected from the power outlet, and all parts have cooled before cleaning or storing.

• Use a clean, dry cloth to clean all external surfaces of the air purifier.
• Store the air purifier in an upright position. Do not store anything on top of the unit.

NOTE: More frequent cleaning may be required depending on environmental conditions.

BREVILLE RECOMMENDS: Always ensure the air purifier is turned off, switched off at the power outlet, unplugged, and allowed to cool before performing any cleaning or filter replacement.

X DO NOT stick any foreign objects or fingers inside the air inlet/outlet of this unit.

X DO NOT use gasoline, benzine, thinner, or harsh cleaners on or in the unit while cleaning, as they will damage the unit.

X NEVER use alcohol or other solvents on this unit.

CLEANING THE SENSOR

• Keeping the air quality sensor clean is important for optimal performance.
• The sensor is located behind a grill at the rear of the unit.
• Gently vacuum the sensor grill using a small hand brush tool at least once a month.
• If more dust is visible behind the grill, remove the cover by using the raised tab. Push inwards and outwards simultaneously to open the cover; it may be tight.
• Gently vacuum the metal shield of the air quality sensor with the hand brush tool.
• Replace the cover when clean, ensuring it clicks into place.

WARNING: The air quality sensor is fragile and can be damaged by excessive force. Use extra care when cleaning.

FILTER CLEANING AND REPLACING

WARNING: The filter is not washable. Do not immerse any part of the air purifier in water, as this will cause damage.

• The Pre-filter should be cleaned at least once every month using a vacuum cleaner. Gently vacuum with a brush or upholstery tool attachment. Clean more often if required.
• Do not attempt to clean the carbon filter with a vacuum, as this can cause damage.
• Do not use any solutions, hard bristle brushes, or sharp objects for cleaning, as this can cause damage.
• Replace the filter as indicated in the following instructions.

REPLACING THE FILTER

The filter should be replaced according to the timeframes indicated:

• Filter life is approximately 6 months with 24-hour daily use, or 12 months with 12-hour daily use. Filter life may vary based on environmental conditions.
• Remove all packaging from the replacement filter and place it into the unit as described below.
• 1. Carefully turn the air purifier upside down and remove the locking knob from the base.
• 2. Remove the base plate.
• 3. Remove the used filter, being careful of any residue or debris that may fall.
• 4. Insert the replacement filter, ensuring it is correctly fitted and centered.
• 5. Replace the base plate and refasten the locking knob.
• 6. Return the air purifier to an upright position.
• 7. Turn on the air purifier, then press and hold the Microbe Shield™/Night Mode/Filter Reset button for 5 seconds to reset the Filter Reset light.

NOTE: The filter has no top or bottom and can be placed in either orientation.

NOTE: The air purifier will not operate if the filter is not in place or not fitted correctly.

UV-C LIGHT CARE

Replacement of the UV-C light must be performed at an authorized Breville service centre. Contact Breville Customer Service Centre for support.

REPLACEMENT FILTERS

Replacement filters can be purchased from the Breville website or participating retail outlets. See the table below for product codes:

Delivery charges may apply.

Please contact Breville Customer Service Centre for further support.

Only use original Breville filters intended for this appliance.

WARNING: Unintended use or damage to the housing may result in the escape of dangerous Microbe Shield™ UV-C radiation, which is harmful to eyes and skin. Never operate the UV-C light outside the air purifier.

Troubleshooting

MINI TROUBLESHOOTING GUIDE

Before performing any service checks, unplug the unit from the mains.

NOTE:

Breville Customer Service Centre

Australian Customers
Phone: 1300 139 798
Web: www.breville.com

New Zealand Customers
Phone: 0800 273 845
Web: www.breville.com

Breville, the Breville logo, Master Every Moment, Smart Air, SensAir, Breville Home Connect, and the Microbe Shield logo are trademarks of Breville Pty. Ltd. A.B.N. 98 000 092 928. Copyright Breville Pty. Ltd. 2020.

Due to continued product improvement, the products illustrated/photographed in this booklet may vary slightly from the actual product.

LAP308 ANZ B20