Klein Tools 56417 Rechargeable Dual-Beam Area Light

General Specifications

• Operating/Storage Altitude: 6562 ft. (2000 m)
• Operating Temperature: 5°F to 104°F (-15°C to 40°C)
• Charging Temperature: 41°F to 95°F (5°C to 35°C)
• Storage Temperature: -4°F to 140°F (-20°C to 60°C)
• Relative Humidity: <85% non-condensing
• Lighting Modes: All-On (3000 Lumens, 3 hrs), Spot Light (HIGH: 1400 Lumens, 5 hrs; LOW: 475 Lumens, 9.5 hrs), Flood Light (HIGH: 1400 Lumens, 8 hrs; MEDIUM: 700 Lumens, 10 hrs; LOW: 250 Lumens, 12 hrs)
• Battery Type: 18650, Lithium-Ion (x2)
• Battery Capacity: 6700mAh (24Wh)
• Charging Time: Approx. 3 to 6 hours
• Charging Requirements: DC 5V, Max. 2A (USB-C)
• Output: DC 5V, Max. 2.4A (USB-A)
• Dimensions: 5.2" × 7.6" × 3.5" (132 × 193 × 89 mm)
• Weight: 2.2 lb. (998 g)
• Drop Protection: 9.8 ft. (3 m)
• Ingress Protection Rating: IP65
• Certifications: CE, UKCA, REACH, RoHS, DOE/CEC, NRCAN, UL 1576, CSA C22.2 No. 250.5

Safety Warnings

Read and follow all instructions to ensure safe operation. Failure to do so may result in fire, electric shock, serious injury, or property damage.

• The lens gets very hot during use. Do not touch hot lens to avoid burns.
• Keep away from combustible materials while in operation. Do not cover the lens. Ensure the proximity sensor is clear of debris.
• Do not use if the product or battery is damaged or modified.
• Do not open, crush, heat above maximum temperature, or incinerate the battery.
• Do not immerse in water or other liquids.
• Properly seal the charging port cover to maintain water and foreign object ingress protection. Keep the seal clean.
• Do not open the charging port cover if wet or in a wet environment. Dry thoroughly before opening.
• Do not subject to impacts or drops greater than 9.8 ft. (3 m). Replace if severe drops occur.
• Use a safety-rated power supply or wall adapter within specified charging voltage and current.
• Do not stare at the operating lamp.
• Contains a strong magnetic field.
• Not a tether point; not for dropped object prevention.
• Do not attempt to repair the product, battery, or charging cable, except as indicated in the MAINTENANCE section.

Feature Details (FIG. A)

• 1 Power Button: Turns the light on/off and cycles through modes.
• 2 Battery Status Indicator: Shows battery charge level.
• 3 USB-C Input Port: For charging the area light.
• 4 USB-A Output Port: For charging other devices.
• 5 USB Port Cover: Protects the USB ports.
• 6 Flood Light (24 LEDs): Provides broad illumination.
• 7 Spot Light: Provides focused illumination.
• 8 Proximity Sensor: Detects if the spot light lens is blocked and reduces output to prevent overheating.
• 9 Latching MODbox Rail Hooks: For attaching to MODbox rails.
• 10 Stationary MODbox Rail Hooks: For attaching to MODbox rails.
• 11 Rotating Hanging Hook: For hanging the light.
• 12 Magnets: For magnetic mounting.
• 13 Base: Provides stability and mounting points.
• 14 USB-C Cable: Included for charging.

Operating Instructions

Charging

• Use a Class 2 power unit.
• Connect the USB-C cable to the light and a USB port or AC adapter (not included). Ensure the adapter does not exceed 5V, 2.0A.
• The Battery Status Indicator (2) will illuminate during charging.
• A full charge takes 3-6 hours. Charge completely before first use.
• The area light can be operated while charging.
• Keep the USB Port Cover (5) closed when not in use to maintain IP rating.

Battery Status Indicator

Press and release the Power Button (1) while the unit is off to check battery level:

If the unit does not power on, the battery may be fully depleted. Charge for at least four hours.

Power Button Functions (1)

• To Turn On: Press and hold the Power Button.
• To Cycle Modes: Press and release the Power Button to cycle through: All-On, Spot High, Spot Low, Flood High, Flood Medium, Flood Low.
• To Turn Off: Press and hold the Power Button while in any mode.
• The light will power on in the last used mode.

Battery Internal Temperature Protection

If the internal temperature is outside specified ranges, the Battery Level Indicator LEDs will blink alternately (Green/Yellow, Green/Red), and the product will shut down. Operation will resume when the temperature returns to normal.

Proximity Sensor (8)

In All-on or Spot Light mode, the sensor detects if the Spot Light lens (7) is blocked and automatically reduces light output to prevent overheating. The sensor may not work if the lens is covered in water or dirt.

To test: With the Spot Light on, cover the area with a solid object. The first green LED of the Battery Status Indicator (2) should blink, lights dim over seven seconds, then blink three times. Remove the blockage to return to original brightness. If this does not occur, clean the sensor with a cotton swab or soft brush and test again. If the issue persists, discontinue use and replace the unit.

Power Sharing (Charging Devices)

Connect a charging cable to the USB-A Output Port (4) and the device to be charged. The Battery Status Indicator (2) will show charging has begun. Use the device's original cable for best results.

MODbox Rail Mounting

1. Hook the Latching MODbox Rail Hooks (9) onto the top or bottom rail of the MODbox unit (FIG. B).
2. Push the bottom of the Base (13) to separate the hooks, and swing the Stationary MODbox Rail Hooks (10) over the rails (FIG. C).
3. Release pressure to close the hooks and secure the Area Light (FIG. D).
4. Reverse the process to remove the Area Light.

Maintenance

Cleaning

Ensure the device is disconnected from all power sources. Use a clean, dry, soft, lint-free cloth to wipe the unit. Do not use abrasive cleaners or solvents.

Storage

• For storage over one month, charge fully before storing. Recharge approximately every three months.
• Store in cool temperatures, mild humidity, and away from direct sunlight.
• Avoid extreme hot or cold temperatures, as this can reduce service life and performance. Keep away from corrosive chemicals and gases.
• Inspect the device visually after storage before recharging or charging other devices. Allow the unit to return to ambient conditions before use.

Recharging

• Recharge as needed. Avoid regularly discharging the battery completely, as this can impact its overall life.
• Regularly inspect ports and the charging cable for debris, dirt, damage, or corrosion. Do not attempt repairs; replace the device or cable if necessary.

Troubleshooting

56417 will NOT charge if:

• The cable is not properly connected to the charger output or battery input. Check connections.
• The charging cable is damaged. Replace with an equivalent cable.
• The charging port or device cannot supply the minimum voltage and current for charging. Connect to an appropriate charging source.
• The charger is damaged. Replace the charger.

Warranty

For warranty information, visit: www.kleintools.com/warranty

Disposal / Recycle

Dispose of equipment and accessories in accordance with local regulations. For more information, visit www.epa.gov/recycle.