User Manual for KONTAL models including: K003-01, K004-01, RKA2 Rolan Receivers, RKA2, Rolan Receivers, Receivers
Index of /docs/RKA2/
29 авг. 2024 г. — Batteries are not covered by the warranty in battery operated products. In products whose shelf life has expired, malfunctions caused by battery liquid ...
File Info : application/pdf, 8 Pages, 1.41MB
DocumentDocumentROLAN RECEIVERS RKA/RKA2 User Manual V1.1 Please read the user manual carefully before using your device. Pay attention to the installation, electrical connection and initial start sections and follow the specified steps. The product owner/user should keep this user manual in a known and visible place throughout the life of the product. · Batteries are not covered by the warranty in battery operated products. In products whose shelf life has expired, malfunctions caused by battery liquid discharge or leakage are not covered by the warranty. · All service and repairs can only be done by Kontal Elektronik. The product should not be intervened by any other persons. · The operating voltage of the product is described on its label. Do not power the product with a different source outside this voltage range. If the product is used in violation of the above-mentioned items, it may cause fire, personal injury, or damage to the product or the structure in which the product is installed. Kontal Elektronik Ltd does not accept any responsibility for such situations caused by the user. This exclamation mark will be used to highlight important points. Do not touch supply input of the product with bare hands. ü This electric mark will be used to highlight electricity hazard. This sign on the label indicates that the supply voltage of the product is DC. This symbol on the product or its box indicates that this product cannot be treated as normal household waste. Instead, the product should be delivered to designated collection points for the recycling of electronic equipment. Incorrect disposal of the product can have negative consequences for the environment and human health. Legal rights and responsibilities of this document and its revisions belong to Kontal Elektronik Ltd. It is illegal and prohibited to change it without permission. KONTAL ELEKTRONK ROLAN RECEIVERS K003-01/K004-01 1 1. DEFINITION RKA and RKA2 are receivers designed for Rolan model remote controls. The RKA allows control of a device with 1 relay, while the RKA2 provides control with 2 relays, and the RKA4 offers control with 4 relays. 2. TECHNICAL FEATURES TECHNICAL FEATURES Model Product Code Working Voltage Working Current Working Frequency Channel Number Contact Type Max. Contact Power Auto Learn Remote Control Capacity Weight Dimensions RKA K003-01 12 24V DC 50mA @24V DC 433.92MHz 1 Dry Contact / NO 250V AC 10A ü 650 95gr 82.5 x 108,5 x 35mm RKA2 K004-01 12 24V DC 80mA @24V DC 433.92MHz 2 Dry Contact / NO 250V AC 10A ü 650 106gr 82.5x 108.5 x 35 mm RKA4 K005-01 220V AC 50Hz 433.92MHz 4 Dry Contact /NO/NC 250V AC 10A ü 650 344gr 91,4 x 156 x 45,4mm For the processes described below to be performed correctly, ROLAN model remotes must be programmed with your LCD CODER device. Additionally, a Rolan Receiver can only recognize remotes that have the SAME `RECEIVER CODE'. This means you cannot program a remote with a different receiver code to the SAME RECEIVER at the SAME TIME. If you have remotes and receivers with MK product codes (these remotes are usually marked with a scorpion logo on the back), you do not need the LCD Coder. You can directly teach MK-coded Rolan products to your receiver without additional programming. In this case, the automatic learning mode of the receivers is disabled for security reasons. You will need to teach each remote to the receiver using the standard learning method. In this manual, you can see sections about second relay output. These sections are related to model RKA2 and model RKA don't have these specifications. 2.1. TEACHING REMOTES TO ROLAN RECEVERS 1. First of all, if you have a LCD Coder, you must program the remotes using the device. 2. Power up to device correctly. 3. When Rolan receiver powered, you can hear warning sound. If this beeps for, o Three time: there is no remote in Rolan receiver memory. o One time: remotes have been taught to the Rolan receiver before. KONTAL ELEKTRONK ROLAN RECEIVERS K003-01/K004-01 2 4. The receiver board has a single button that performs two functions: it allows you to teach a new remote to the receiver or delete all previously taught remotes. To enter the remote learning mode, press and hold the button for 1-2 seconds, then release it. When the receiver enters learning mode, the buzzer on the receiver board will remain active for approximately 6-7 seconds, during which you will hear a beep from the buzzer. While the buzzer is emitting the sound, press the button on the remote you wish to teach. When the receiver successfully learns the remote, the buzzer will emit 3-4 quick beeps and then stop. If the receiver fails to learn the remote, it will exit the learning mode, and the buzzer will stop emitting sound. 5. If you are teaching a remote to the receiver for the first time, the channel of the taught remote will set the system's operating channel. All subsequent remotes must have the same channel as the system's operating channel. In summary, you can only program remotes with the SAME channel to a single receiver. 6. For 2-channel and 4-channel receivers, the channel of the remote you have taught will activate the receiver's 1st relay. Subsequent remote channels will automatically activate the other relays. For example, if you have taught the 1st button of a 4-channel remote to the receiver system, the 1st channel of the remote will control the receiver's 1st relay. The 2nd button of the remote will control the receiver's 2nd relay, the 3rd button will control the 3rd relay, and the 4th button will control the 4th relay. There is no need to specifically teach these channels to the receiver. The control board will automatically recognize these channels. 2.2. DELETING MEMORY OF ROLAN RECEIVER 1. Disconnect the power supply from the receiver board. 2. While the power is disconnected, press and hold the button on the receiver board, and keep your finger on the button. 3. With your finger still on the button, reconnect the power to the receiver board. When the receiver board powers up, you will start hearing a beep from the buzzer. Continue holding the button until the beep sound stops. Once the beep stops, any remotes previously taught to the receiver will be erased from the control board's memory. KONTAL ELEKTRONK ROLAN RECEIVERS K003-01/K004-01 3 RKA/RKA2 CONNECTION SCHEMA NO (Normal Open) NC (Normal Close) 12V Supply 24V Supply 12/24V DC Figure 1 RKA/RKA2 Connection Scheme Ensure the device is turned off while connecting cables. Do not touch the terminals after the device is turned on. KONTAL ELEKTRONK ROLAN RECEIVERS K003-01/K004-01 4 RKA4 CONNECTION SCHEMA NO (Normal Open, Normal Açik) NC (Normal Close, Normal Kapali) NO (Normal Open, Normal Açik) NC (Normal Close, Normal Kapali) Figure 2 - RKA4 Connection Scheme Ensure the device is turned off while connecting cables. Do not touch the terminals after the device is turned on. KONTAL ELEKTRONK ROLAN RECEIVERS K003-01/K004-01 5 DIPS. NO FONKSYON DIPS. NO DIPS. KONUMU FUNCTION MODE RELAY 2 MODE RELAY 1 LEARNING AUTO Dip No 1 Dip No 1 OFF ON AUTO LEARNING WORKING Dip No 2 Dip No 2 OFF ON WORKING MODE AND ADDITION TIMING SETTINGS FOR RELAY 1 WORKING Dip No 3 O N Dip No 3 OF F Dip No 4 WORKING MODE RELAY3 Dip No 4 OFF ON WORKING MODE AND ADDITION TIMING SETTINGS FOR RELAY 2 FUNCTION DEFINITION ONE AND DOUBLE CHANNEL ROLAN RECEIVERS (RKA / RKA2) FUNCTION DEFINITION FOUR CHANNEL ROLAN RECEIVER (RKA4) Auto learning is active. Thus, you don't need to touch the device. Auto learning is active. Auto learning is passive. Auto learning is passive. Relay 1 mode is toggle. When you push the remote button, relay is to be active or passive. Toggle mode is active for Relay 1 Relay 1 mode is pulse. When you push remote button relay is active for 0,3 seconds, then returns to Pulse mode is active for Relay 1 passive. If first relay mode is pulse, (when dipswitch 2 is OFF), relay working time increases one second. Toggle mode is active for Relay 2 No addition time. Pulse mode is active for Relay 2 Relay 2 mode is toggle. When you push the remote button, relay is active or passive. Toggle mode is active for Relay 3 Relay 2 mode is pulse. When you push remote button, relay is to be active for 0,3 seconds then Pulse mode is active for Relay 3 passive. If first relay mode is pulse, (when dipswitch 4 is OFF), relay working time increases one second. Toggle mode is active for Relay 4 No addition time. Pulse mode is active for Relay 4 Lock Channel mode is active. In this mode, only one relay work at the same time. Lock Channel mode is active. Lock Channel mode is passive. Lock Channel mode is passive. Relay 1 and relay 2 work synchronously. All relays work synchronously. Synchronous working mode is passive. Synchronous working mode is passive. Relay 1 is working according to Relay 2. Relay 1 and Relay 2 work together but remote button of Relay 2 Toggle mode activated for all relays. disabled. Button of relay 1 controls both. Relay 2 is working according to Relay 1. Relay 2 and Relay 1 work together but remote button of Relay 1 Pulse mode activated for all relays. disabled. Button of relay 2 controls both. Dip No 5 WORKING MODE RELAY 4 Dip No 5 OFF ON Dip No 6 LOCK CHANNEL Dip No 6 OFF ON LOCK CHANNEL Dip No 7 SYNCHRONOUS MODE TYPE O N Dip No 7 SYNCHRONOUS WORKINGMODE OF F Dip No 8 TYPE OF SYNCHRONOUS WORKING O N Dip No 8 SYNCHRONOUS WORKING CHANNEL OF F KONTAL ELEKTRONK ROLAN RECEIVERS K003-01/K004-01 6 4.INSTALLATION Please install the device in an easy-to-access location for easy separation during installation. It is recommended to use a maximum cable length of 40 cm when connecting the unit. KONTAL ELEKTRONK Manufacturer / Authorized Service Kontal Elektronik San. Ve Tic. Ltd. ti. Çorapçilar Sanayi Sitesi A Blok NO: 1-2 kitelli OSB ROLAN RSETACENIBVUELR/STURKK0E0Y3-01/K004-01 7 +90 212 485 6111 www.kontal.com.tr