Installation Guide for SOLAX POWER models including: X1 Boost Solar Power Inverter, X1, Boost Solar Power Inverter, Solar Power Inverter, Power Inverter, Inverter
SolaX Power
Sitemap - SolaX Power Network Technology (Zhejiang) Co.,Ltd.
Quick Installation Guide X1 Series 3.0KW-6.0KW I Packing Lists Inverter (with bracket)* 1 Positive DC pin contact * 2 Negative DC pin contact * 2 Female DC connector * 2 Male DC connector * 2 AC connector * 1 Documents Expansion bolt*3 Flat gasket*3 Self-tapping screw*3 Earth terminal*1 Wi-Fi dongle (optional), LAN/GRPS dongle (optional)*1 * For the optional accessories, please be subject to the actual delivery. II Inverter Installation - Unscrew the bracket from the back of the inverter. - And mark the position(223 mm*30 mm) of three holes. PH1 cross screwdriver; Torque: 0.8±0.1 N.m 223 X1 30 - Drill holes with 10 drill. - Depth: at least 60 mm. - Tighten the expansion bolts. - Screw the expansion screws. - Match the inverter with the bracket. - Screw the cross recessed screw on the right side. - make sure available space 300 mm Torque: 0.8±0.1 N.m 300 mm 300 mm 300 mm X1 300 mm III Cable size: 4 mm² strip length: 7.0 mm PV Connection -Align the four halves connectors. positive DC pin contact negative DC cable pin contact × clamp contact + + - PV array male plug nut female plug tight nut + +- PV1 - +- PV2 Inverter Note! The PV connection mode as the diagram shown is not allowed! IV AC Connection strip length 52.5mm outer jacket 6mm 55mm Model X1-3.0/3.3/3.6K X1-4.2/4.6K X1-5.0/5.5/6K L,N cable(mm²) 4-6 5-6 Inverte5r-+6BMU PE cable(mm²) Micro-breaker 2.5-6 20A 2.5-6 25A 2.5-6 32A 1.Slide the cable nut and back shell onto the cable. 2.Insert the stripped end of each three wires into holes in the female insert, then tighten each screw. Ph1 cross screwdriver; Torque: 0.5±0.1 N.m N L PE 5.Connect the AC plug to the inverter. 3.Screw down the threaded sleeve of the pressure screw. 4.Screw down the pressure screw. Firmware Upgrading 1) Make sure the DC switch is off and the AC is disconnected with grid. User can update the inverter system through the U-disk. Please contact SolaX service to get the latest firmware. Then add a new folder named "Update" in the root directory on your U-disk, and two more sub-folders named "ARM" and "DSP" under "Update". Please copy the firmware files into ARM and DSP respectively. It will be like: "Update\ARM\618.00207.00_XX_XXXXX_XXXX_XXX_ARM_Vx.xx_xxxxxxxx.usb"; "Update\DSP\618.00381.00_XX_XXXXX_XXXX_XXX_DSP_Vx.xx_xxxxxxxx.usb" 2) Press and hold the "v" key for 5 seconds to enter Off Mode. Then insert the U-disk into the "DONGLE" port. V Connections and Overview - Screw the ground screw with 4 hexagon wrench shown as follow. Torque:1.5±0.2 N.m CT/DRM/Meter/RS485 Torque:1.0±0.1N.m RS485 port DRM/Meter/RS485 - Prepare the RJ45 connector and the communication cable, following the PIN definition and assembly order below, then insert the RJ45 connector into the corresponding RS485 port of the inverter, and tighten the waterproof connector. 1 8 PIN 1 2 3 4 5 6 7 8 Definition CT+ Com/DRM0 GND_COM Meter_A/ 485_A Meter_B/ E_Stop 485_B RefGen CT- Public grid, inverter side AC port CT L line arrow point to the public grid - Overview for connection. - After checking all connections are correct, turn on the external DC /AC breakers. - Turn on the DC switch to the "ON" position. - Inverter will start automatically when PV panels generate enough energy. The LED will be blue and the LCD screen will display the main interface. Firmware Upgrading Ø For the inverter with LCD, user can refer to the following: 3) When the user turns on all the switches, the LCD will show pictures as below. And at the same time, the user can choose the program you need by pressing short Up and Down, and long press "V" to confirm and upgrade the inverter. ARM DSP Cancel OK Update(ARM) >618.00207.00... ... Update(ARM) Updating----25% ARM DSP Update(DSP) >618.00381.00... ... Update(DSP) Updating----25% 4) After the upgrade is complete, please remember to turn off the DC switch and AC switch, then pull off the Udisk. * Please contact our service support to get the latest firmware, and unzip it into your U-disk by following the steps above. Do not modify the firmware file name ! Otherwise it may cause damage to the inverter! 320102024902CorelDRAW 2021 3-Heights(TM) PDF Optimization Shell 5.9.1.5 (http://www -tools.com)