Security - Genexis
Installation Guide for genexis models including: XGS2410B Fiber Twist, XGS2410B, Fiber Twist, Twist
FiberTwist XGS2410B - Genexis
2 дек. 2024 г. — Remove Blind Cover (if present). 1. Press and hold the unlock button (see button overview). 2. Rotate the Blind Cover counterclockwise till it blocks.
File Info : application/pdf, 7 Pages, 1.04MB
DocumentDocumentFiberTwist XGS2410B Installation Guide Button overview Unlock button Remove FiberTwist or Blind Cover press and hold while twisting counterclockwise Reset button (recessed) Reset - press and release Factory reset - press and hold the button until System and Uplink LED start to blink LED dim button Dim LEDs press and release to dim LEDs in steps Port overview LAN ports Power port ON/OFF button ON/OFF button Power ON or OFF press and release to switch device ON or OFF LED overview System Green system ok Green (blinking) booting Red system or booting failure Red (blinking) - insufficient PON signal Off power off Uplink Green link ok Green (blinking) link establishing Off no link System + Uplink Green (blinking) firmware upgrade Installation guide Box contents · Genexis FiberTwist (active device) · Power adapter · Labels (self-adhesive) Label position The product label is positioned on the back of the active device. Preparation Ensure there is a power socket within reach of where the device is being installed. Important: Instructions need to be followed precisely and uninterrupted. This minimizes the risk of damage to the fiber optic connectors, causing a severe degradation of signal quality. Remove Blind Cover (if present) 1. Press and hold the unlock button (see button overview). 2. Rotate the Blind Cover counterclockwise till it blocks. 3. Remove the Blind Cover from the baseplate (FTU) by pulling it towards yourself. 4. Store the Blind Cover in a safe place. Remove dust cap 1. Take the FiberTwist out of the box. 2. The dust cap is connected to the red string located on the rear of the FiberTwist. 3. Remove the dust cap by pulling the red string. 4. Store the dust cap in a safe place. Twist! 1. Place the FiberTwist on the FTU as shown in the picture below, in a 30degree angle. 2. Rotate clockwise until it clicks into place. 3. Make sure the FiberTwist is aligned squarely on the FTU, each edge must line up directly with the FTU below. Your FiberTwist is now installed! Connecting the FiberTwist 1. Connect your gateway to the LAN (10GE) port via an RJ45 network cable. A CAT6 cable or better is recommended. 2. Connect the supplied power adapter to the FiberTwist and plug the adapter into a power socket. 3. Press the ON/OFF button to power on the device. If at some point in the future it becomes necessary to uninstall the FiberTwist, please place the Blind Cover back on the FTU immediately and put the dust cap back on the FiberTwist. Warning: This product contains a laser that emits invisible light. It is a Class 1 Consumer Laser product according to EN 50689:2021, which means it is safe under all conditions of normal use. However, it is still advised to not look directly into the fiber connector when the product is powered on. Warning: Do not cover the device, this will interfere with the ventilation. Ambient Operating Temperature: 0°C ~ 40°C Security vulnerabilities can be reported at: https://genexis.eu/security EU Declaration of Conformity Hereby, Genexis Netherlands B.V. declares that the product FiberTwistXGS2410B is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, Delegated Directive 2015/863 and Ecodesign Directive 2009/125/EC. The full text of the EU declaration of conformity is available at: https://genexis.eu/product/fibertwist-xgs2410b/#downloads Company Name Genexis Netherlands B.V. Company Address Lodewijkstraat 1a 5652 AC Eindhoven The Netherlands Name and title of authorized person Maarten Egmond, CTO Signature of authorized person Place of issue Eindhoven The Netherlands Date of issue 2024-12-02 Revision 1.1 - December 2024 - Copyright © 2024 Genexis Netherlands B.V. All rights reserved. Multiple languages of this document and additional product information are available on https://genexis.eu/product/fibertwist-xgs2410b/#downloads Genexis assumes no responsibility for any inaccuracies in this document. Genexis reserves the right to change, modify, transfer, or otherwise revise this publication without notice.