Installation Guide for DIAMONDBACK models including: CVR-7, Heavy Duty Truck Bed Cover, CVR-7 Heavy Duty Truck Bed Cover
RAM 1500 New Body Силова кришка кузову (DIAMONDBACK) без RAMBOX CrewCab 2019-2023 (42399) цена, описание, фото
Installation Guides – DiamondBack Covers
Aluminum Locking Tonneau Covers | DiamondBack SE Truck Cover – DiamondBack Covers
HD SE '19up Ram 1500 INSTALLATION GUIDE CVR-7 45 minutes Normal install time Keep an eye out for these icons: PARTS INCLUDED: IMPORTANT! Important installation information Helpful Hints Tips to assist installation TOOLS REQUIRED: Cab Panel Center Panel Bed-Rail Edge Trim (4) 1/8" Hex Key Ratchet Wrench, (Torque Wrench preferred) 9/16" Socket Tail Panel Cap Clamps (4) Gas Springs (4) Utility Knife 7/16" Socket PRE-INSTALLATION NOTES (REVIEW ALL OTHER INCLUDED INSTALLATION GUIDES BEFORE BEGINNING) If you're installing a rear window protection accessory, mount it prior to mounting the cover. Some models require bulkhead preparation first. Please refer to the instructions in the bulkhead prep kit prior to mounting the cover. If your cover includes shims, affix the included bed rail shims first and reference their included instructions. MOUNT THE PANELS 1 Place the center panel across the bed, cheated toward the tailgate. Each panel is tapered front to back. Make sure the arrow on the underside of the panel is pointed toward the tailgate. Position the cover front to back so that the front of the cab panel 4 lines up with the outside edge of the center of the bulkhead. Center the cover side-to-side on the truck. Attach the tail panel by holding it at a 90° angle from the bed rails and 2 mate the driver's side hinge first, followed by the passenger side's c-shaped hinge. MATE FIRST 90° MATE SECOND 5 Position the cap clamps as far apart as possible under the center panel. Attach the center panel by uniformly tightening a cap clamp using a 9/16" socket to between 5-6 f -lbs. While tightening clamps, be aware of possible bed rail cap deformation. Overtightening clamps will damage bed rail caps and cause leaking. Retighten af er a week of use. Check them every time you haul on top. CAUTION! Be sure all hinges are fully mated before lowering panels. 3 In the same way, attach the cab panel but start by mating the passenger side first. Make sure the safety catch has been untaped and then lower panel into position. PREP FOR THE LOCK RODS Unbolt and move one of the bolts 6 of the lock-rod guide brackets to the second, unoccupied slot using a 7/16" socket. Repeat this on each of the cover's four brackets. 7/16" DiamondBackCovers.com / 800 935 4002 CLAMPS INSTALLED If your plastic bed rail cap extends below 7 the metal edge of your bed rail, trim the excess at each lock rod location so that it's flush with the metal bed rail's edge. On Multi-Function Tailgate models, only the tail panel lock rods will need edge trim so you will only use 2 pieces. The cab panel lock rods will utilize the corner brackets as shown in Step 9. CUT 2" NOTCH IN BED RAIL CAP CONTINUED ON NEXT PAGE > ADJUST THE LOCK RODS Loosen set screws for the tail and cab panel lock rods with the provided 8 hex key and retighten each lock rod after ensuring three things... 1/8" hex key After properly aligning the lock 9 rods in the closed position, it is time to tighten all brackets using a 7/16" socket. To ensure a tight seal, it is crucial to simultaneously push up on the bracket AND apply downward pressure on the cover. Repeat for tail panel bracket locations. For Multi-Function Tailgates: Repeat steps 89 for the cab panel, but instead of bracing the lock rods against the bed rails themselves, use the oblong holes in the side legs of the factory corner brackets. CORRECT ORIENTATION HANDLE OPEN HANDLE CLOSED The Z bend orientation is always maintained With the lock handle in the open position, the rod tips clear the bed rails. With the handle in the closed position, the rod tips do not hit the bed walls. The panels may be tough to open and close at first. Leave the panels closed as much as possible to allow the weatherstrip to break in. Af er a few days, you'll find things working smoothly. The cab panel has a safety spring lock handle ensuring you engage the lock rods when closing the panel. This helps prevent accidental opening of the panel while driving. If you are installing a Cross Bin, do so now. Refer to the Cross Bin Installation Guide for details. ATTACH THE BED RAIL EDGE TRIM metal plastic 10 Peel the red adhesive backing from the edge trim pieces. Affix them to the metal bed rail in the correct orientation at the points where the lock rods pass underneath. Bed rail edge trim protects the lock rod end cap from wear, and helps draw the panels down and compress the weatherstrip. When installed properly, it will be a little tough to turn the lock handle at first. ATTACH THE GAS SPRINGS & SAFETY CATCH Open the cab panel. 11 Have a 2nd person support it in the open position. Loop the end of the cable tethers around the ball stud arms, making sure to go beyond the ball stud and nut. Attach the safety catch by pulling down on the panel and pushing the 13 keyhole at the bottom of the safety catch around the nut, making sure to engage the spring clip. HIMGODHUOPNNRTOETTSHISOSUPEREENND UP XX LBS 12 Attach 2 gas springs to the cab panel. Make sure the barrel end is up. If you install your gas springs upside down, they'll fail. If 2 of your gas springs have heavier poundage printed on them, use them here. DiamondBackCovers.com / 800 935 4002 HMIOGDUHONPTNRTOETHSISOSUPEERNEND UP XX LBS With the safety catch in place, your cab panel will only open partially. To fully open the panel, pull down on panel while using your other hand to push up on the flat part of the catch until it disengages. 14 Attach the 2 remaining gas springs on the tail panel, again making sure the barrel end is up. 15 Leave the cover closed and locked for 24 hours to allow the pressure-sensitive weatherstrip adhesive to fully cure. 24 hours Adhesive cure time For first 2 weeks af er installation open tail panel on cover before operating tailgate. AUGUST 2022Adobe PDF library 16.07