User Manual for Shenzhen Linkyou Innovation models including: U8, 2AXLDU8, U8 Smart Watch, U8, Smart Watch
Shenzhen Linkyou Innovation Co., Ltd U8 Smart Watch 2AXLDU8 2AXLDU8 u8
User Manual Thank you for using our smart watchPlease read the User Manual before using it . I. Product overview Display Button Strap Heart rate sensor Charging port Packing list: X1 X1 X1 Smart Watch X1 Charging Cable X1 User Manual X1 . II. Charging 2, 5V/1A The product should be charged for more than 2 hours before use. This product is with magnetic charging. Please use power adapter of 5V/1A. After charging for a while, the display will show the charging indication. . APP III. APP Download and Connection 1. APP APP Download APP Gloryfit APP name: Gloryfit IOSAndroidAPP StoreGoogle Play"Gloryfit"; For iPhone users, search"Gloryfit"in App Store and download the app. For Android phone users, search"Gloryfit"in Google Play to download and installor install it by scanning the code as follows: IOS 9.0Android 4.4, 4.0 Note: the system of mobile phone must be IOS 9.0 or above, or Android 4.4 or above. Bluetooth 4.0 or above. 2. APP APP connection (Android 6.0GPS) Step 1: turn on Bluetooth and GPS location. Remarks: Android 6.0 and above mobile phones need to turn on GPS location to connect Watch. "Gloryfit"APP Step 2: open"Gloryfit"app, register and log in. : APP """EG-C420" ; Step 3: Make the watch close to the mobile phone, select "device" in the app, and click it to search for"EG-C420", then click connection. APP"""" Step 4: after successful connection, please set"device"and "me" in the app according to your needs. . IV.Basic operation 1. Power on/off a. 3 Power on: Please press the side button for 3 seconds when the watch is in shutdown mode. b. Wake up: When the watch in standby mode, just short press the side button or touch the screen to wake up. c. 3 Power offPlease press the side button for 3 seconds to shut down or select"shut down"in the settings. 2. Switch dial operation 3 APP In current dial interface, touch the display screen for more than 3 seconds to enter the dial switching mode, and then slide left and right to switch the dial. Finally touch the screen to confirm. In addition, you can also get various exquisite dials pushed from APP . 3. Touch panel operation 1 Sliding screen operation , When in TIME dial interface, A. Slide up to show the latest messages from your phone. B. Slide down to show the status bar interface, including screen brightness adjustment, settings, bluetooth connection status, remaining power, etc. C. Slide to left or right showing the steps, heart rate measurement, exercise modes ,weather and stopwatch, etc. 2 Click operation If you want to enter the sub interface of an interface, please click the screen to enter. If you need to exit, please slide the display screen to the right or press the side button lightly. Press the side button in any interface to return to the main interface. . V. Function introduction 1. Pedometer APP The watch has the function of Pedometer, calorie consumption and mileage monitoring. You can view the Pedometer value on the watch, and the app can save the daily record. 2. Heart rate monitoring APP"", 24 APP There is a "Auto test " switch for heart rate monitoring in app settings. If the "Auto test" is turned on, your heart rate will be monitored 24 hours real-time after wearing, and recorded and saved in app. You can also test your heart rate in the heart rate interface of your watch. 3. Training ""GPS GPS"Gloryfit"APP"Go"GPSAPP "Training" interface contains a variety of sports modes. Click in to monitor exercise duration and heart rate. If you need to connect GPS for running or riding, you can open the mobile phone GPS location and "Gloryfit"APP, and click "GO" to connect to the mobile phone GPS to get the movement track and speed, the record will be saved in app. 4. Weather You can check the weather for today. 5. Stopwatch In the stopwatch interface of your watch, Touch the screen or press the side button to start and end. Slide the screen to the right to exit. 6. Message push and call reminder APPTwitter You can open a lot of social information In the app, such as twitter, and push the SMS content to the watch for display. You can also set phone call reminder and click reject. 7. Sleep monitoring APP When you wear your watch to sleep at night, you can monitor the duration of deep sleep, light sleep, and awake time, and save the data in the app. 8. Sedentary reminder APP You can set the sedentary reminder period In the app. 9. Alarm clock APP You can set the alarm clock in the app. 10. : Find your phone: ""1 When the watch and mobile phone are connected via Bluetooth, you can search your mobile phone through the "Find your phone" function of the watch. the phone will turn off ringing automatically when it rings for1minute. . VI. Attention 1. The product will be continuously upgraded. It is normal that some functions described in the user manual are slightly different from the software after purchase or during use. 2. 5V/1A Please charge for over 2 hours with 5V/1A adapter for the first time. 3. IOS9.0Android 4.44.0 Please ensure that the connected mobile phone system is IOS9.0 or above, or Android 4.4 or above, and the bluetooth version of the phone is 4.0 or above. 4. IP68 The waterproof grade is IP68, you can wear it to wash your hands, take a shower, but do not diving and soak in water for a long time, and do not touch hot water. 5. , Sleep monitoring is only applicable at night. Its principle is to calculate the duration of deep sleep and light sleep based on the roll over frequency and heart rate during sleep. It is a normal phenomenon that there is a little error in sleep and waking time, especially when you put on watch too late or put it on when you are going to sleep, it may cause errors. if you wear it all the time and wear it tightly, it will be more accurate. 6. In order not to affect the heart rate test, please tear off the protective film of the heart rate lens on the back of the watch. . VII. FAQ 1. Can't search watch in app? A. GPS Please check whether your mobile phone's bluetooth and GPS location have been turned on. B. 0.5 Please make sure the watch is within 0.5 meters of your mobile phone and the watch has enough power. C. IOS9.0Android 4.44.0 Please check if your mobile system is IOS 9.0 or above, or Android 4.4 or above, Bluetooth 4.0 or above. D. iPhone "" If your watch is connected to another phone, Please unbind the previously connected mobile phone, Especially with the iPhone. Not only need to unbind, but also need to operate " Forget this device " in the Bluetooth Setting of your phone. Another phone can search and connect to this watch. 2. Why can't the watch be charged A. 5V/1A Please make sure to use the standard charging cable in the packageAnd use a 5V/1A power adapter. B. 5V/1A5V/2A If the watch cannot be charged with 5V/1A adapter after the first use or long time no use, try charging with 5V/2A C. If the watch hasn't been charged for a long time, it will take a few minutes to show the charging indicator on the display. D. Please make sure there is no sweat at the charging port when chargingIf there is any water, please clean it before charging. . VIII. Specification Realtek RTL8762CK 1.54"IPS 240 X240 260mAH 5V 2-3 43 250 X 37 X 11.3mm -5~45 iOS 9.0Android 4.4 CPURealtek RTL8762CK Display screen: 1.54" IPS TFT Resolution: 240 X 240 Battery: 260mAh Charging Voltage5V Charging Time2-3 hours Weight: 43g Dimensions: 250 X 37 X 11.3mm Operating temperature-5°~45° Support OSIOS 9.0 & Android 4.4 and above FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.