LAGAN L Refrigerator Installation Guide
Model: AA-2552560-2
Important Safety Information
⚠️ WARNING! Before proceeding with installation, read the safety information in the User Manual.
Serious or fatal crushing injuries can occur from refrigerator tip-over. Always secure this refrigerator to the wall using tip-over restraints.
Do not use an extension cable or multi-plug while plugging it into the electricity circuit.
This manual provides installation instructions in English. Safety information is also available in multiple languages on pages 3 and 4 of the original document.
Product Overview and Dimensions
This document outlines the installation process for the IKEA LAGAN L refrigerator/freezer.
Included Parts:
- A x1
- B x2
- C x2
- D x1
- E x2
Dimensions:
- Height: 1773 mm
- Width: 920 mm
- Depth: 568 mm (appliance body), 547 mm (main cabinet depth)
- Power Cord Length: 1700 mm
- Door Opening Angle: 135°
- Height from floor to top of cabinet: 1773 mm
- Height of freezer compartment: 625 mm
- Height of refrigerator compartment: 1104 mm
- Clearance for door opening: 76 mm (side)
Installation Steps
Step 1: Prepare the Appliance
Ensure you have the necessary tools: screwdrivers (Phillips and flathead), wrench, gloves, and a spirit level. The diagrams show tools and parts A, B, C, D, E.
The initial diagrams illustrate preparing the unit, potentially removing protective films or packaging.
Step 2: Door Hinge Adjustment/Removal Preparation
This step involves preparing the door hinges for potential removal or adjustment. It shows using a screwdriver to loosen or remove screws securing the hinge mechanisms.
Step 3: Remove Bottom Kick Panel
The diagram shows removing the lower panel at the base of the refrigerator, likely to access internal components or for door removal.
Step 4: Remove Main Door
This step details the process of removing the main refrigerator door. It involves carefully detaching the door from its hinges by unscrewing specific fittings and then lifting the door away.
Step 5: Remove Freezer Drawer
The freezer drawer is removed by carefully pulling it out and then detaching it from its runners or guides.
Step 6: Prepare for Door Reversal (if applicable)
This section shows preparing the hinge components for potential reversal of the door opening direction. It involves removing screws and possibly reorienting parts.
Step 7: Door Reversal Process
Detailed steps for reversing the door swing. This involves transferring hinge components from one side to the other, ensuring correct alignment and re-securing screws.
Step 8: Re-attach Main Door
The main refrigerator door is re-attached to the appliance by aligning the hinges with their corresponding mounting points and securing them with screws.
Step 9: Re-attach Freezer Drawer
The freezer drawer is re-inserted into the appliance, ensuring it slides smoothly onto its runners.
Step 10: Re-attach Bottom Kick Panel
The bottom kick panel is re-attached to the base of the refrigerator.
Step 11: Final Door Adjustments
Fine-tuning the door alignment. This step involves adjusting screws on the hinges to ensure the doors close properly and are level.
Step 12: Adjust Leveling Feet
The refrigerator is placed in its final position. The leveling feet at the bottom are adjusted by rotating them (clockwise or counter-clockwise) to ensure the appliance is stable and level. ⬆️⬇️ arrows indicate adjustment.
Step 13: Final Door Alignment Check
A final check of the door alignment and closing mechanism. The diagram shows adjusting hinge screws for precise door positioning.
Step 14: Secure to Wall (Tip-Over Restraint)
Crucial Safety Step: Use parts E (brackets) and C (screws) to securely fasten the refrigerator to the wall. The diagrams show attaching brackets to the rear of the appliance and then to the wall. This prevents accidental tipping.
Note: Wall mounting hardware may vary depending on your wall type. Ensure appropriate fixings are used.
Step 15: Final Checks and Positioning
The diagrams show final checks of the appliance's stability and door operation. The appliance is shown in its final upright position.
Step 16: Wait Before Powering On
⚠️ After installation and positioning, wait at least 4 hours (⏰ 4h) before plugging the appliance into the electrical outlet (?).
