User Manual for YUER models including: MS-MPS4-80FC, MS-MPS4-80FC 80W With LED Circle Moving Head Light, MS-MPS4-80FC, 80W With LED Circle Moving Head Light, LED Circle Moving Head Light, Moving Head Light, Head Light, Light
YUER 4x80w LED beam moving head Bar light RGBW 4in1 with ring DMX512 stage Effect lighting for DJ Disco wedding party Club User’s manual:
YUER™ 4x80W LED beam moving head Bar light RGBW 4in1 with ring DMX512 – yuerlights
File Info : application/pdf, 18 Pages, 477.49KB
DocumentDocumentFour Heads 80W with LED Circle Moving Head Light (4×80W RGBW 4IN1 LED, RGB 3IN1 LED Circle) User Manual Please read this user manual before using the product. I. Checking before using No. Item Quantity Unit 1 Four heads 80w moving head light 1 piece 2 0.75m² power cable with blue head 1 piece 3 User manual 1 piece 4 Bracket 2 pieces 5 Clamp (optional) 6 Safety cable Optional 7 DMX signal cable For the sake of safety and under the terms, it does not allow unauthorized restructuring or modification of this product. Please note that improper use and human damage caused by this product, it can not be covered by our warranty. Also, unprofessional operations will cause short circuits, burns or shocks, and more either. The machine has been rigorously tested before shipment. Please comply with the instructions of the operation requirements, to ensure the product can be running safely under normal circumstances. Any damage caused by improper operation will result in the termination of the warranty claim. We are not accept any property lost and responsibility of human being improper use and unprofessional operation. Please place user manual in a safe place for reference. After selling,renting or carrying, you can give it to new owner. Attention: Base on our products keep improving by our company,our user manual data is subject to change without notice. We will remain rights of changing product specification. II. Safety Instruction 1. When opening the packing, take all accessories out, and remove the light to a horizontal table for good operation. First check whether the accessories are complete, then check carefully whether the whole light has no damage. If there is any damage, please contact us as soon as possible. 2. AC Power: Check whether the local power supply is accordance with the requirements of the product rated voltage. 3. The product is only suitable for indoor working environment. The light should keep dry, keep away from wet, overheat or dusty environment. Don't come into contact with water and other liquids to prevent or reduce the risk of electric shock or fire. 4. Please do not install the light directly on the surface of the combustible substance. 5. The people who install, operate and maintain of light professional certificate required. 6. When there are faults of the light, please stop using the light immediately. Don't try to repair, please contact the nearest authorized technical assistance center, if the parts damage, always use the same type of parts replaced. 7. Don't touch any electrical wiring in the process of operation to prevent the risk of electric shock. 8. To make sure the light working environment temperature, the highest do not exceed 40 ,the lowest do not exceed - 20 . 9. Under the stable cooling working situation, the highest temperature of the housing of the light can reach 80 , please do not touch. 10. The light is design according to the type of electric shock protection. The light should be use in good connection grounding power system and the ground wire must connect with the ground wire of the power supply system. The earth sign port of the light should be connected to the installing fixtures. 11. Do not use the damage of the insulating layer wire and also do not use the power cord overlap on the other wire. When not in use or clean the light, please disconnect the power, don't pull the plug in hard or just drag the wires. 12. There are no components inside for maintenance. Before start operation the light, please check whether all of the shell is installed. In the case of the shell open used the light is prohibited. Note: Under any installation, maintenance and clean the light, please confirm that has cut off the power cord! III. Product specification Category Voltage Power consumption LED source Channel Illuminance X rotation angle Y rotation angle Color Dimming Display Fuse Control mode Size N.W. Parameter AC100240V50/60HZ 290W 4pcs 80W RGBW 4in1 LED, 60pcs 0.2W RGB 3in1 LED Circle 8CH12CH23CH36CH and 60CH Color @3M @5M Unit R1 12900 4220 G1 B1 23000 5235 7800 1700 Lux W1 53000 18600 0~540° 0~220° Individually control 0-100%, linear dimming 2.4inch TFT LCD display F5AL250V DMX Master/slave Sound control Auto run 1004*121*273MM 11.9kg IV. Display menu Item SQ Button: Silkscreen MENU ENTER Function Enter/check menu Check the last menu Check the next menu Enter/check menu V. Lighting installation 1How to install Be mounted on the truss, etc. Be mounted the light with 2pcs bracket (including in the package) and 2pcs clamps (purchased from the company or the local market) on the truss, etc. It is important to tighten up the brackets and clamps. Completed as shown below, different kinds of lighting effect can be achieved according to the needs and configuration of multiple lighting fixture, like making the lights be lined up or form the circle. Hung up on the stand. Install the light according to the below figure. Stands can be bought from us or from the local market. There are 1.8m and 2.5m stands available for purchase VI. Display Main Function: Menu DMX Address Channel Mode Slave Mode Auto Mode Sound Mode Pan Invert Tilt Invert Advanced Settings System Settings Options and settings 001512 8/12/23/36/60CH Master Slave Show Mode Show00 Show01-16 Show Speed 0099 Show Mode Sound Sens Head1 Head2 Head3 Head4 Head1 Head2 Head3 Head4 Reset Display Display invert DMX Fail Software Show00 Show01-16 00 01-99 No/Yes No/Yes No/Yes No/Yes No/Yes No/Yes No/Yes No/Yes No/Yes On/Off No/Yes Auto Black Hold V1.1 Function description DMX address code Channel mode rotation Master mode Slave mode Random show Show mode 1-16 Slow to fast Random sound control performance Sound control mode 1-16 No sound control Sound control sensitivity: 1 (low)-99 (high) X1 does not invert /invert X2 does not invert /invert X3 does not invert /invert X4 does not invert /invert Y1 does not invert /invert Y2 does not invert /invert Y3 does not invert /invert Y4 does not invert /invert Reset Display on/off Display do not invert /invert Auto run mode Standby mode Hold the DMX status Version VII. How to operate Here are three ways to operate Master/slave build-in program to control Connecting all the lights with DMX signal cable. To prevent interference, it's best to connect less than or equal to 17 units at a time. The program would work in Master/slave mode automatically by default. (The machines will automatically choose the main and slave ones if all in master status.) Specify one of the lighting fixture as the master one, and setting the rest as the slave ones. All the slave machines will work following the master machine. Master modeAuto Mode or Sound ModeShow00-16 Slave mode optionSlave DMX controller detailed instructions as follow: VIII. DMX Controller If control the lights by DMX controller, address code must be set first. The address code value is between 1 to 512, and the lights can receive the DMX signal accordingly. Press "MENU", select "DMX Address" menu option, then press "ENTER". Use / to select DMX512 address code. Our initial address code is 001. After setting it, press the ENTER to save. Connect the DMX512 console output port to the first slave device DMX input port, and connect the first slave device DMX output port to the second slave device DMX input port with signal cable, until all slave connections are complete. DMX Connection required terminal device (Loop connection) In the installation process, if the DMX cable laid in a long distance, or the machines are in noisy environment, such as KTV or Dancing Hall, the DMX terminal (loop connection) is recommended.This can avoid the turbidity of digital control signals caused by electrical noise. The DMX terminal is made up of a simple XLR connector (2-pin and 3-pin) connecting to a 120 resistor. Please insert the terminal into the XLR output port of the last product. VII. Chanel mode instructionchoose DMX 001 default address code [Sheet 1] DMX Channel (8CH) CH Function Value Function 1 LED dimming 000 - 255 LED linear total dimming, 000-100% 2 Strobe 000 - 255 Strobe, slow to fast 000 - 007 No function 008 - 022 Show 1 3 Show/sound 023 - 037 Show 2 control mode 038 - 052 Show 3 053 - 067 Show 4 068 - 082 Show 5 083 - 097 Show 6 098 - 112 Show 7 113 - 127 Show 8 128 - 142 Show 9 143 - 157 Show 10 158 - 172 Show 11 173 - 187 Show 12 188 - 202 Show 13 203 - 217 Show 14 218 - 232 Show 15 233 - 247 Show 16 248 - 255 Sound control mode 4 Speed/ sensitivity 000 - 255 Show mode speed, slow - fast Sound control sensitivity, low - high 5 LED color 000 - 030 031 - 255 Color chasing (color changing Static color selection (sheet 6) 6 Color chasing 000 - 255 Color chasing, slow - fast 7 SMD show color 000 - 255 Show color selection (sheet 7) 8 seSleMctDion background 000 - 255 color SMD background color selection (sheet 7) selection [Sheet 2] DMX Channel (12CH) CH Function Value 1 Pan position 000 - 255 2 Tilt position 000 - 255 3 LED dimming 000 - 255 4 Strobe 000 - 255 000 - 007 008 - 022 5 Show/ sound 023 - 037 control mode 038 - 052 053 - 067 068 - 082 Function X, 0-540° Y, 0-220° LED linear total dimming, 000-100% Strobe, slow - fast No function Show 1 Show 2 Show 3 Show 4 Show 5 083 - 097 098 - 112 113 - 127 128 - 142 143 - 157 158 - 172 173 - 187 188 - 202 203 - 217 218 - 232 Show 6 Show 7 Show 8 Show 9 Show 10 Show 11 Show 12 Show 13 Show 14 Show 15 233 - 247 248 - 255 Show 16 Sound mode 6 Speed/ sensitivity 000 - 255 Show mode speed, slow - fast Sound control sensitivity, low - high 7 Color 000 - 030 031 - 255 8 Color chasing 000 - 255 Color chasing LED color selection (sheet 6) Color chasing speed, slow - fast 9 Pan fine 000 - 255 Pan file 10 Tilt fine 000 - 255 SMD show 11 color selection 000 - 255 cSoMloDr o 12 background 000 - 255 color selection Tilt fine Show color selection (sheet 7) SMD background color selection (sheet 7) [Sheet 3] DMX Channel (23CH) CH Function Value 1 LED dimming 000 - 255 2 Strobe 000 - 255 3 Red 000 - 255 4 Green 000 - 255 5 Blue 000 - 255 6 White 000 - 255 7 SMD effect 000 - 255 Function LED total dimming, 000-100% Strobe, slow - fast R dimming, 0-100% G dimming, 0-100% B dimming, 0-100% W dimming, 0-100% SMD effect selection (sheet 8) 8 SMD effect speed 000 - 255 SMD effect speed, slow - fast 9 SMD show color selection 000 - 255 SMD show color selection (sheet 7) 10 SMD background 000 - 255 color selection 11 X1 000 - 255 SMD background color selection (sheet 7) X1, 0-540° 12 Y1 000 - 255 Y1, 0-220° 13 LED1 switch 000 - 255 14 X2 000 - 255 15 Y2 000 - 255 16 LED2 switch 000 - 255 17 X3 000 - 255 18 Y3 000 - 255 19 LED3 switch 000 - 255 20 X4 000 - 255 21 Y4 000 - 255 22 LED4 switch 000 - 255 23 Rotation speed 000 - 255 LED1 on, 0-100% X2, 0-540° Y2, 0-220° LED2 on, 0-100% X3, 0-540° Y3, 0-220° LED3 on, 0-100% X4, 0-540° Y4, 0-220° LED4 on, 0-100% Motor rotation speed, slow - fast [Sheet 4] DMX Channel (36CH) CH Function Value 1 LED dimming 000 - 255 2 Strobe 000 - 255 3 X1 000 - 255 4 X1 fine 000 - 255 5 Y1 000 - 255 6 Y1 fine 000 - 255 7 Rotating speed 000 - 255 8 LED1 color 000 - 255 9 X2 000 - 255 10 X2 fine 000 - 255 11 Y2 000 - 255 12 Y2 fine 000 - 255 13 Rotating speed 000 - 255 14 LED2 color 000 - 255 Function LED total dimming, 0-100% Strobe, slow - fast X1, 0-540° X1 fine Y1, 0-220° Y1 fine X1/Y1 rotation speed, fast - slow LED1 color selection (sheet 6) X2, 0-540° X2 fine Y2, 0-220° Y2 fine X2/Y2 rotation speed, fast - slow LED2 color selection (sheet 6) 15 X3 000 - 255 X3, 0-540° 16 X3 fine 000 - 255 X3 fine 17 Y3 000 - 255 Y3, 0-220° 18 Y3 fine 000 - 255 Y3 fine 19 Rotating speed 000 - 255 X3/Y3 rotation speed, fast - slow 20 LED3 color 000 - 255 LED3 color selection (sheet 6) 21 X4 000 - 255 X4, 0-540° 22 X4 fine 000 - 255 X4 fine 23 Y4 000 - 255 Y4, 0-220° 24 Y4 fine 000 - 255 Y4 fine 25 Rotating speed 000 - 255 X4/Y4 rotation speed, fast - slow 26 LED4 color 000 - 255 LED4 color selection (sheet 6) 000 - 199 No function 27 Sound control 200 - 209 mode 210 - 240 Reset No function 241 - 255 Sound control mode 28 Sensitivity 000 - 255 Sound control sensitivity, low - high 29 Red 000 - 255 R dimming, 0-100% 30 Green 000 - 255 G dimming, 0-100% 31 Blue 000 - 255 B dimming, 0-100% 32 White 000 - 255 W dimming, 0-100% 33 SMD effect 000 - 255 SMD effect selection (sheet 8) 34 SMD effect speed 000 - 255 SMD effect speed, slow - fast 35 SMD show color selection 000 - 255 SMD show color selection (sheet 7) SMD 36 background 000 - 255 color selection SMD background color selection (sheet 7) [Sheet 5] DMX Channel (60CH) The first head effect (CH114) CH Function Value 1 X1 000 - 255 2 X1 fine 000 - 255 3 Y1 000 - 255 Function X1, 0-540° X1 fine Y1, 0-220° 4 Y1 fine 000 - 255 Y1 fine 5 Rotation speed 000 - 255 X1/Y1 rotation speed, fast to slow 6 LED1 dimming 000 - 255 LED1 total dimmer, 0-100% 7 LED1 strobe 000 - 255 LED1 strobe, slow to fast 8 LED1 color 000 - 255 LED1 color selection (sheet 6) 000 - 007 No function 008 - 030 First PAR, show mode 1 031 - 053 First PAR, show mode 2 9 Show/reset 054 - 076 077 - 099 First PAR, show mode 3 First PAR, show mode 4 100 - 122 First PAR, sound control mode 123 - 199 No function 200 - 224 First PAR, stay 3-5S, automatic reset 225 255 No function 10 Show speed 000 - 255 First PAR, show speed, slow to fast 11 LED1 000 - 255 R dimming, 0-100% 12 LED1 000 - 255 G dimming, 0-100% 13 LED1 000 - 255 B dimming, 0-100% 14 LED1 000 - 255 W dimming, 0-100% The second head effect (CH1528) CH Function Value Function 15 X2 000 - 255 X2 , 0-540° 16 X2 fine 000 - 255 X2 fine 17 Y2 000 - 255 Y2, 0-220° 18 Y2 fine 000 - 255 Y2 fine 19 Rotation 000 - 255 X2/Y2 rotation speed, fast to slow 20 LED2 total dimmer 000 - 255 LED2 total dimmer, 0-100% 21 LED2 strobe 000 - 255 LED2 strobe, slow to fast 22 LED2 color 000 - 255 LED2 color selection (sheet 6) 000 - 007 No function 008 - 030 Second PAR, show mode 1 031 - 053 The second PAR, show mode 2 23 Show/rest 054 - 076 077 - 099 The second PAR, show mode 3 The second PAR, show mode 4 100 - 122 The second PAR, sound control mode 123 - 199 No function 200 - 224 The second PAR, stay3-5S, automatic reset 225 255 No function 24 Show speed 000 - 255 The second PAR, show speed, slow to fast 25 LED2 000 - 255 R dimming, 0-100% 26 LED2 000 - 255 G dimming 0-100% 27 LED2 000 - 255 B dimming, 0-100% 28 LED2 000 - 255 W dimming, 0-100% The third head effect (CH2942) CH Function Value Function 29 X3 000 - 255 X3, 0-540° 30 X3 fine 000 - 255 X3 fine 31 Y3 000 - 255 Y3, 0-220° 32 Y3 fine 000 - 255 Y3 fine 33 Rotation speed 000 - 255 X3/Y3 rotation speed, fast to slow 34 LED3 dimming 000 - 255 LED3 total dimming, 0-100% 35 LED3 strobe 000 - 255 LED3 strobe, slow to fast 36 LED3 color 000 - 255 LED3 color selection (sheet 6) 000 - 007 No function 008 - 030 The third PAR, show mode 1 031 - 053 The third PAR, show mode 2 054 - 076 The third PAR, show mode 3 37 Show/reset 077 - 099 The third PAR, show mode 4 100 - 122 The third PAR, sound control mode 123 - 199 No function 200 - 224 The third PAR, stay3-5S, automatic reset 225 255 No function 38 Show speed 000 - 255 The third PAR, show speed, slow to fast 39 LED3 000 - 255 R dimming, 0-100% 40 LED3 000 - 255 G dimming, 0-100% 41 LED3 000 - 255 B dimming, 0-100% 42 LED3 000 - 255 W dimming, 0-100% The fourth head effect (CH4360) CH Function Value 43 X4 000 - 255 44 X4 fine 000 - 255 Function X4, 0-540° X4 fine 45 Y4 000 - 255 Y4, 0-220° 46 Y4 fine 000 - 255 Y4 fine 47 Rotation 000 - 255 X4/Y4 rotation speed, fast to slow 48 LED4 dimming 000 - 255 LED4 total dimmer, 0-100% 49 LED4 strobe 000 - 255 LED4 strobe, slow to fast 50 LED4 color 000 - 255 LED4 color selection (sheet 6) 000 - 007 No function 008 - 030 Fourth PAR, show mode 1 031 - 053 Fourth PAR, show mode 2 054 - 076 Fourth PAR, show mode 3 51 Show/reset 077 - 099 Fourth PAR, show mode 4 100 - 122 Fourth PAR, sound control mode 123 - 199 No function 200 - 224 Fourth PAR, stay 3-5S, automatic reset 225 255 No function 52 Show speed 000 - 255 Fourth PAR, show speed, slow to fast 53 LED4 000 - 255 R dimming, 0-100% 54 LED4 000 - 255 G dimming, 0-100% 55 LED4 000 - 255 B dimming, 0-100% 56 LED4 000 - 255 W dimming, 0-100% 57 SMD effect 000 - 255 SMD effect (sheet 8) 58 SMD effect speed 000 - 255 SMD effect speed, slow - fast 58 SMD show color selection 000 - 255 SMD show color selection (sheet 7) 59 SMD show 000 - 255 SMD show color selection (sheet 7) color selection SMD 60 background 000 - 255 color selection SMD background color selection (sheet 7) [Sheet 6] DMX Channel (LED color selection, value sheet) [Sheet 7] DMX Channel (SMD show color, background color selection, value sheet) 000 - 015 No color 016 - 031 Red 032 - 047 Green 048 - 063 Blue 064 - 079 White 080 - 095 SMD show 096 - 111 Amber Cyan color, 112 - 127 Warm yellow background 128 - 143 Purple color selection 144 - 159 Yellow 160 - 175 Turquoise 176 - 191 Lavender 192 - 207 Pink 208 - 223 Cold color 224 - 239 Magenta 240 255 Warm white [Sheet 8] DMX Channel (SMD show effect, value sheet) 000 - 015 No effect 016 - 039 Effect 1 040 - 063 Effect 2 064 - 087 Effect 3 088 - 111 Effect 4 Show effect 112 - 125 Effect 5 126 - 129 Effect 6 130 - 153 Effect 7 154 - 177 Effect 8 178 - 201 Effect 9 202 - 255 Effect 10 X. Product maintenance and cleaning Please note the following points when testing this product: All the screws and parts for installing must be tightly connected and cannot be rusted; Housings, lenses, fixtures and mounting locations (e.g ceilings, hangers, trusses, etc.) must not be deformed; The power cable must not be damaged.The installation and use must be operated by trained professional technicians and it must ensure that safety hazards are eliminated. The installation and use of the product must be carried out by trained professional technicians, and it must be ensured that safety hazards are eliminated. Note: Please unplug the power cable before doing product maintenance! It is very important to keep machine clean and dry. Before unlock the machine or start maintenance,you should keep the machine power off and unplug. Keep cleaning regularly can make the light have max brightness and also can extend its use time. We suggest to use good glass cleaner and clean it with a soft cloth. Can not use alcohol or chemical solvents under any circumstances. The interior of the machine and the fan should be cleaned at least once every season by using a vacuum cleaner.WPS 文字