Extron - The AV Technology LeaderExtron - The AV Technology LeaderExtron Electronics
Installation Guide for Extron models including: Cubby F55 UT Retractor for Cable, Cubby F55 UT, Retractor for Cable, Cable, Retractor
12 oct. 2022 — This guide provides instructions for an experienced technician to install the Extron Retractor for the Cable Cubby F55 UT. Enclosure.
File Info : application/pdf, 6 Pages, 2.18MB
DocumentDocumentRetractor for Cable Cubby F55 UT · Installation Guide cGionomsttproulIewcMttewioPuwnsO.see,xrRatgrnToudAnids.cNepo,eTimcn:isffitocarallttahioteinosn. This guide provides instructions for an experienced technician to install the Extron Retractor for the Cable Cubby® F55 UT Enclosure. Additional instructions are available in the user guide for the Cable Cubby F55 UT Enclosure at www.extron.com. NOTE: For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide on the Extron website. Inward Install (Final Assembly) Planning The retractor modules can be mounted inward or outward depending on available undertable clearance and accessibility. Up to two retractor modules can be installed per enclosure. NOTE: Inward mounting is recommended for installations with limited clearance. For new installations, to determine the best location for the enclosure, keep in mind the undertable space required for the retractor modules (see Determining Under-table Clearance for more info). Required Tools and Additional Accessories Outward Install (Final Assembly) #6 x 1/2" Wood Screw Flex55 Adapter Module Two 1/4"-20 Screws Marker Pen Retractor Bracket Thumb Screw Retractor bezel Figure 1. Tools and Accessories Tape Measure Zip Ties Support Bracket Phillips Screw Driver Determining Under-table Clearance The diagram on the following page shows the space required for a retractor module installation in a Cable Cubby F55 UT enclosure. NOTES: · To prevent objects from impeding cable retraction, ensure the exposed cable clears nearby obstructions. · Excess cabling can cause clearance issues. Use zip ties to secure undertable cabling to prevent accidental contact or entanglement with users. 1 Retractor for Cable Cubby F55 UT · Installation Guide (Continued) Mounting Orientations and Dimensions The following diagrams illustrate the mounting dimensions for outward, double outward, and inward retractor module orientations. 24.95" (63.38 cm) REAR 8.55" (21.7 cm) FRONT Outward Installation 39.36" (99.98 cm) REAR FRONT Double Outward Installation 18.40" (46.73 cm) 8.55" (21.7 cm) REAR FRONT Inward Installation 8.55" (21.7 cm) Figure 2. Cable Cubby F55 UT with Retractor Modules - Mounting Orientations and Dimensions Preparing the Enclosure Ensure the retractor has adequate undertable clearance for installation (see previous section). You should have the required accessories for mounting the retractor and to configure the enclosure. CAUTION: Disconnect the power from the Cable Cubby enclosure before beginning a retractor system installation. ATTENTION : Débranchez l'alimentation du boîtier Cable Cubby avant de commencer l'installation d'un système de rétracteur. 2 Preparing the Retractor Modules Product Category Cable Release Assembly 1 Remove two enclosure screws (one on each side) from this position for angular mounting. Connector (or Stop Collar) 2 Rotate the cable release assembly to the angled position for installation. Figure 3. Preparing the Retractor Modules Installation Retractor Bracket Installation Insert the retractor bracket into the desired right or left rear mounting slot (1) and secure with the included thumb screw (2). 1 Front Rear 1 Insert the retractor bracket into the desired right or left rear mounting slot . Retractor Bracket 2 Thumb Screw Figure 4. Installing the Retractor Bracket 2 Thumb Screw Bottom View Secure the bracket with the included thumb screw. 3 Product Category Plastic Inserts Installation If installing the Retractor outward, insert the retractor bezel with the openingside facing outward. If installing inward, install facing inward. Outward Install Inward Install 1 2 1 2 Figure 5. Installing the Flex55 Adapter Module and Retractor Bezel Support Bracket installation Attach the support bracket to the retractor end cap, using the provided 1/4"-20 screw. Figure 6. Installing the Support Bracket NOTE: Do not overtighten. The bracket screw only needs to be snug. Overtightening could deform the end cap and cause misalignment of the retractor, resulting in poor cable extension and retraction. 4 Retractor for Cable Cubby F55 UT · Installation Guide (Continued) Retractor Installation Insert the retractor into the retractor bracket slot. 1 Outward Retractor Install Secure the retractor locking screw. 3 2 Secure with the provided 1/4" #20 screw. Figure 7. Installing the Retractor into the Cable Cubby F55 UT enclosure NOTE: Do not overtighten. The locking screw (3) only needs to be snug. Support Bracket Mounting Ensure the bracket is flush with the surface and mark the mounting hole. 1 2 Drill a 3/32" pilot hole through the marked location and fasten with the supplied screw. Figure 8. Mounting the Support Bracket ATTENTION: · Ensure the supplied #6 1/2'' L screw does not pierce through the top of the table. Use an appropriate screw based on the table material and thickness. · Assurez vous que le #6 1/2'' L vis fournies ne transpercent pas la surface de la table. Utilisez de vis plus appropriées en fonction du matériau de la table et de son épaisseur. 5 Confirm Proper Cable Extension and Retraction To extend the cable, hold it by the connector and pull the cable from the retractor module to its full length. To retract the cable, see the diagram below. CAUTION: Use one hand to control the cable as it retracts. A cable allowed to retract too quickly and without control can cause possible injury to the user or damage the furniture surface, Cable Cubby, and nearby items. ATTENTION : Utilisez une main pour contrôler le câble lorsqu'il se rétracte. Un câble qu'on laisse se rétracter trop rapidement et qu'on ne contrôle pas peut provoquer d'éventuelles blessures ou endommager la surface du meuble, du Cable Cubby, ou des objets à proximité. 2 Press and hold the cable release button. 1 Hold the cable taut by the connector. 3 Slowly allow the cable to pull back until the stop collar (or connector) is seated against the cable release assembly. 4 Release both cable and button. Figure 9. Confirming Proper Cable Retraction · If the cable does not retract to suit your application, see "Speed Control Adjustment" in the Retractor Series User Guide at www.extron.com for more information. · If the stop collar (or connector) does not seat fully against the cable release assembly, confirm proper tension adjustment using the instructions on the product label. For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide on the Extron website. © 2022 Extron -- All rights reserved. www.extron.com All trademarks mentioned are the property of their respective owners. Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876 68-3738-50 Rev. A 08 22