Installation Guide for NEOUSYS models including: Nuvo-9100VTC, Nuvo-9200VTC, Nuvo-9000VTC Series Rugged Embedded Computer, Series Rugged Embedded Computer, Rugged Embedded Computer, Embedded Computer, Computer
File Info : application/pdf, 6 Pages, 5.69MB
DocumentDocumentNuvo-9100/9200VTC Series Quick Introduction Guide Warning · Only qualified service personnel should install and service this product to avoid injury. · Observe all ESD procedures during installation to avoid damaging the equipment. 1 Preparing tools Unpack the equipment and make sure the following tools are available and delivered contents are correct. 1-1. User-provided tools · Anti-static wrist wrap 1-2. Packing List Item Description Quantity 01 Nuvo-9000VTC series system 1 02 CPU bracket 1 03 Nuvo-9100VTC damping bracket 1 Nuvo-9200VTC damping bracket 2 04 Foot pad 4 05 3-pin pluggable terminal block 2 06 2.5" HDD/SSD thermal pad (if HDD not installed) 1 07 Rubber spacer (barebone system only) 4 08 Screw pack 1 09 12x grommets (Nuvo-9100VTC) 4x grommets + 4x sleeves (Nuvo-9200VTC) 2 Overview - Front Panel Nuvo-9100VTC Series Nuvo-9200VTC Series 3 USB3.2 Gen2x1 Port 4 USB2.0 Port 5 CMOS Reset Button The system's USB 3.2 Gen2x1 ports (10Gbps) are implemented via native xHCI (eXtensible Host Controller Interface) controller and are backward compatible with USB3.2 Gen.1 USB 2.0, USB 1.1 and USB 1.0 devices. UEFI USB is also supported so you can use USB keyboard/ mouse in UEFI shell environment. Indicated in red are screw-lock holes for the corresponding USB port. xHCI driver is supported natively in Windows 10, therefore you do not need to install the xHCI driver prior to utilizing USB functions. The USB2.0 ports are implemented via native xHCI (eXtensible Host Controller Interface) and are backward compatible with USB 1.1 and USB 1.0 devices. UEFI USB support is also provided so you can use USB keyboard/ mouse in UEFI shell environment. Indicated in red is a screw-lock hole for the corresponding USB port. xHCI driver is supported natively in Windows 10, therefore you do not need to install xHCI driver to utilize USB functions. The CMOS Reset button is used to manually reset the motherboard BIOS in case of system halt or malfunction. To avoid unexpected operation, it is purposely placed behind the panel. To reset, disconnect the DC power input, and use the tip of a pen to press and hold for at least 5 seconds to reset the BIOS. Note You MUST unplug the DC connection to the system before resetting the CMOS. Warning Clearing the CMOS will reset all BIOS settings to default and may result in down time! 6 VGA Port 7 DVI Port 8 USB3.2 Gen1x1 Port VGA connector is the most common video display connection. The VGA output supports up to 1920x1200@60Hz resolution. The system supports triple independent display outputs by connecting display devices to VGA, DVI and DisplayPort connection. To support multiple display outputs and achieve best VGA output resolution in Windows, you need to install corresponding graphics drivers. Note Please make sure your VGA cable includes SDA and SCL (DDC clock and data) signals for correct communication with monitor to get resolution/timing information. A cable without SDA/ SCL can cause blank screen on your VGA monitor due to incorrect resolution/timing output. DVI-D transmits graphics data in digital format and therefore can deliver better image quality at high resolution. The DVI connector on the front panel can either output DVI signals or other digital signals (via an adapter/ cable) depending on the display device connected. It supports resolutions up to 1920x1200@60Hz.The system supports triple independent display outputs by connecting display devices to VGA, DVI and DisplayPort connection. To support multiple display outputs and achieve best DVI output resolution in Windows, you need to install corresponding graphics driver. The system's USB 3.2 Gen1x1 ports (5Gbps) are implemented via native xHCI (eXtensible Host Controller Interface) controller and are backward compatible with USB 2.0, USB 1.1 and USB 1.0 devices. UEFI USB is also supported so you can use USB keyboard/mouse in UEFI shell environment. Indicated in red is a screw-lock hole for the corresponding USB port. xHCI driver is supported natively in Windows 10, therefore you do not need to install the xHCI driver prior to utilizing USB functions. 9 DisplayPort 10 USB3.2 Gen2x2 Type-C Port 11 2. 5G Ethernet and PoE+ Ports The system has a DisplayPort (DP) output which is a digital display interface that mainly connect video source and carry audio to a display device. When connected to a DP, it can deliver up to 8K UHD (7680 x 4320 @ 60Hz) in resolution. The system is designed to support passive DP adapter/ cable. You can connect to other display devices using DP-to-HDMI cable or DP-to-DVI cable. The system's USB 3.2 Gen2x2 type-C port offers up to 20Gbps of data transfer bandwidth, and is implemented via the native xHCI (eXtensible Host Controller Interface) controller. The port is backward compatible with USB3.2 Gen.1 USB 2.0, USB 1.1 and USB 1.0 devices via a USB hub (not included) to connect to external devices. xHCI driver is supported natively in Windows 10, therefore you do not need to install the xHCI driver prior to utilizing USB functions. The system supports triple independent display outputs by connecting display devices to VGA, DVI and DisplayPort connection. To support multiple display outputs and achieve best DisplayPort output resolution in Windows, you need to install corresponding graphics drivers. The ports marked in green/ black are Power over Ethernet (PoE) ports implemented with Intel I225-IT 2.5G Ethernet controller, and marked in blue is implemented using Intel® I219-LM controller that supports Wake-on-LAN and is also compatible with Intel® AMT (Active Management Technology) to support advanced features such as remote SOL desktop and remote on/ off control. The PoE+ ports feature panel screw fix holes (indicated in red) for a firm and secure connection. The ports supply electrical power and data on a standard CAT-5/CAT6 Ethernet cable. Acting as a PoE PSE (Power Sourcing Equipment), compliant with IEEE 802.3at, each PoE port delivers up to 25W to a Powered Device (PD), and the system has a total 100W power PoE budget. 12 Reset Button 13 Status LED Indicator 14 Power Button The reset button is used to manually reset the system in case of system halt or malfunction. To avoid unexpected reset, the button is purposely placed behind the panel. To reset, please use a pin-like object (eg. tip of a pen) to access the reset button. There are four LED indicators on the I/O panel: IGN, WDT, HDD and PWR. The descriptions of these four LED are listed in the following table. The power button is a non-latched switch for ATX mode on/off operation. To turn on the system, press the power button and the PWR LED should light-up green. To turn off the system, issuing a shutdown command in OS is preferred, or you can simply press the power button. To force shutdown when the system freezes, press and hold the power button for 5 seconds. Please note that there is a 5-second interval between on/off operations (i.e. once the system is turned off, there is a 5-second wait before you can power-on the system). 15 2.5"HDD/SSD Hot Swappable Tray 16 Cassette Module Nuvo-9100VTC Nuvo-9200VTC The Nuvo-9100VTC systems support an external 2.5" HDD/ SSD via a hot-swappable slot while Nuvo-9200VTC systems support two external 2.5" HDD/ SSD via hot-swappable slots. Designed for easy access, the HDD/ SSD slot is secured by a lock (indicated in red). Note The tray supports up to 9.5mm thickness HDD/ SSD. The Nuvo-9200VTC systems features a Neousys' patented expansion Cassette (R.O.C. Patent No. M456527) that provides a separated compartment to accommodate an add-on card. It effectively manages thermal conditions of both the system and the add-on card. The modular concept brought by Cassette module also reduces the complexity of installing and replacing an add-on card in the fanless controller. 17 Rear Panel IO Nuvo-9100VTC Nuvo-9104/ 9108VTC Nuvo-9200VTC 18 CAN bus Port Nuvo-9204/ 9208VTC 19 M12 Power over Ethernet Port (Nuvo-9100/ 9200VTC) RJ45 Power over Ethernet Port (Nuvo-9x04/ 9x08VTC) CAN bus is a robust industrial bus with a pair of differential signals and is commonly used in various industrial and in-vehicles applications. The system is equipped with a CAN bus DB9 port that is compatible with both industrial and in-vehicle applications. The CAN bus port supports CAN2.0A and CAN2.0B up to 1Mbps. Pin Definition PoE ports are provided via 8pole, x-coded M12 connectors, offering extraordinary reliability for Ethernet connection. Power over Ethernet (PoE) supplies electrical power along with data on a standard Ethernet cable. As an IEEE 802.3at compliant PSE (Power Sourcing Equipment), each PoE port can deliver up to 25W of power to a Powered Device (PD), such as an IP camera. PoE is able to automatically detect the device connected and determine whether to dispatch power thus it is also compatible with traditional Ethernet devices. The ports supply electrical power along with data on a standard CAT-6 Ethernet cable. Acting as a Power Source Equipment (PSE), compliant with IEEE 802.3at standard, each port can deliver up to 25W of power to a Powered Device (PD), such as a PoE IP camera. PoE is able to automatically detect the device connected and determine whether to dispatch power thus it is also compatible with traditional Ethernet devices. 20 3.5mm Headphone/ Microphone Jack 21 COM Ports The system audio function uses high definition audio. There is a female 4-pole audio jack for headphone (speaker) output and microphone input. The HD audio codec is natively supported in Windows 10 and 11, and no additional drivers are required. COM1 and COM2 (in red) are softwareconfigurable RS-232/ 422/ 485 ports. COM3 and COM4 (in blue) are standard 9-wire RS-232 ports. The operation mode of COM1 and COM2 can be set in BIOS setup utility. The following table describes the pin definition of COM ports. 22 Digital Input/ Output The system provides 4x isolated digital input channels and 4x isolated digital output channels. The DIO functions support polling mode I/O access and DI change-of-state interrupt. 23 3-pin Terminal Block for DC and Ignition Input 24 3-pin Remote On/ Off The system accepts a wide range of DC power input from 8 to 48V via a 3-pin pluggable terminal block, which is fit for field usage where DC power is usually provided. The screw clamping mechanism on the terminal block offers connection reliability when wiring DC power. In addition to DC power input, this terminal block can also accept ignition signal input (IGN). Warning Please make sure the voltage of DC power is correct before you connect it to the system. Supplying a voltage over 48V will damage the system. The "Remote On/ Off" 3-pin connection allows for the connection of an external non-latched switch to turn on/ off the system. It is useful when the system is placed in a cabinet or a not easily accessed location. You may connect an external status LED (20mA) indicator by connecting to PWR LED and GND. 25 Nuvo-9100VTC Damping Bracket Installation The damping bracket comes standard with the system to provide shock and vibration resistance for in-vehicle conditions. Please refer to the exploded view for wall-mount installation. Note If you are mounting the system, place the heatsink fins perpendicular to the ground for better heat dissipation efficiency. 26 Nuvo-9200VTC Damping Bracket Installation a. Available in the accessory box, take out the two brackets and secure them using the six M4 screws provided. b.Please refer to the exploded view for wall-mount installation.Corel PDF Engine Version 15.2.0.695