User Manual for Dellking models including: E0, E0 Bluetooth Helmet Intercom Headset, Helmet Intercom, Helmet Headset, Intercom Headset, Intercom, Headset, Helmet Intercom Headset, E0 Helmet Intercom Headset, Bluetooth Helmet Intercom Headset
Dellking Industrial Co., Ltd E0 2AIO2E0 2AIO2E0 e0
E Please read below content carefully before using thanks for purchasing E0 Bluetooth helmet intercom headset,may you will enjoy it. please read the "Safety Instructions" before using the product for your safety and correct use. FCC ID: 2AIO2E0 Volume control Power on /off/Paring LED indicator Charging interface Microphone PTT button /Phone calls ailure. Temperature range of use:-15--45 Plea Make sure your headset is fully charged three hours before use. From a mains socket. When a red lighte blink, indicating headset is under chaging. After the headset been fully charged, the indicator will show a solid red light. Please note: if have been left too nuch time not charged, the battery lift may be greatly reducen. Therefore it is recommended that you charge the E0 BT headset at least once a month. power on ln power off atate, turn Power on/off Button towards to power icon and hold it for about 3 seconds, until hear a "di"tone, release the button, blue indicator will flash slowly to indicate power on successfully. power off ln power on atate, turn Power on/off Button towards to power icon and hold it for about 6 seconds, until hear a long "di"tone, red indicator will flash quickly to indicate power off. place the E0 Bluetooth headset and the mobile phone in a visible area within 1 meter range. Make sure the Bluethooth headset is in power off state. Turn Power on/off Button towards to power icon for about 8 seconds,when the Blue LED and the Red LED flashing alternately, release the button then the E0 Bluetooth headset is in pairing state now. Follow the user manual of your mobile phone, turn on the Bluetooth function, and searching the Bluethooth headset devices From the found devices in your mobile phone,select the device "Dellking E0 Vxx.xxrelated name, and then try to pair with it, when it prompts to enter password, enter pin code <0000>. Once paired successful,LED Indicator will change from Blue/Red alternately to Blue flashing, and with a "di" tone to note that the Bluetooth headset has connected with your mobile phone. Now your can use the headset to push to talk or answer you phone call. Push To Talk Function For Poc App And Radio Phone After connected to your cell phone Poc(PTT Over Cellphone) app or BluetoothDongle/ Adapter with E0,just push the PTT button to remote control the PTT function.some Poc app may need some setting change Bluetooth before use. Details please refer to the user guide of Poc App. Answer incoming call When there is an incoming phone call,press PTT Button to answer the call, or it may be automatically answered if there's no user operation for 10s. Reject incomin Double press PTT Button to reject an incoming phone call. Hang up call In call active state,double press PTT Button to hang up the call. Voice dial While the E0 is connected with the mobile phone, quick double turn Volume+ Button, then the mobile will prompt you to speak out your desired name. (Note: Voice dial need Mobile Phone supports correspond HFP Voice Dial function) Volume control Turn volume control button towards to "+" icon and hold it, the volume will be louder and louder, when maximum volume reached, a remind tone will be played. turn volume control button to "-"icon and hold it, the volume will be turned lower and lower, when minimum volume reached a remind tone will be played. Model Bluetooth version Operation range Profile Frequency range Occupied Bandwidth Transmitting frequency Talking time Standby time Charging time Working temperature Storage temperature E0 V4.1 Class 2 10m HFP,HSP,PTT 2402-2480MHz 2MHz 20dBm(EIRP) About 6 hours About 50 hours Less than 3 hours -15 ~ 45 -25 ~ 60 LED indicator flash mode LED indicator flashes blue every 2s LED indicator flashes red/ blue alternately and quichly LED indicator flashes red and blue every 2s LED indicator flashes red every 1s LED indicator keeps red State of indication Working/ Standby mode Pairing mode Battery low Charging Charging completed Put E0 headset nearer(less than 10 meter range)to your cell phone. put E0 and cellphone in a least obstacle blocking range. Please send back your BT Speaker-mic head set to our after-sales service department for help if above suggestions fail to solve your problem.Corel PDF Engine Version 22.0.0.412 CorelDRAW 2020