User Manual for RadioShack models including: 3304449, 2BDUR-3304449, 2BDUR3304449, 3304449 3304449-1 Bluetooth Headphone plus USB Dongle, 3304449 3304449-1, Bluetooth Headphone plus USB Dongle, Headphone plus USB Dongle, USB Dongle, Dongle, Headphone
RADIOSHACK WORLDWIDE CORP. 3304449 2BDUR-3304449 2BDUR3304449 3304449
RADIOSHACK WORLDWIDE CORP. 3304449 Bluetooth Headphone 2BDUR-3304449 2BDUR3304449 3304449
RadioShack Bluetooth Headphone+USB Dongle USER MANUAL Bluetooth Headphone Model:3304449 FCC ID: 2BDUR-3304449 USB Dongle Model:3304449-1 FCC ID: 2BDUR-33044491 Package: Headphone Type-C charging cable 2.4GHz dongle User manual Specification: 1. Charging port: Type-C 2. Playing time: up to 25 hours, 50% volume 3. Battery capacity: 3.7V, 500 mAH 4. Bluetooth version: V5.4 5. Speaker driver: 50mm 6. Frequency response: 20Hz-20kHz (Speaker) 7. Sensitivity: 100±3dB(Speaker) 8. Sensitivity: -9.5±3dB(Mic) 9. Bluetooth connection range: approx. 10m Specifications are subject to change and improvement without notice. Actual product may vary from the images found in this document. To... Turn on headphone Button Turn off headphone Play/Pause Answer/end call Reject an incoming call Switching connection mode Switching EQ Press and hold 2 sec and hold 2 sec ×1 ×1 ×2 and hold 2 sec ×1 Note: Music playback is paused during call functions and resumes when the calls ended. On/Off Button Volume Wheel EQ Button Bluetooth Button Charging port How to use: A. Charge 1. Connect the Type-C charging cable to the headphone and a USB source; 2. The LED lights blue when fully charged. B. 2.4GHZ CONNECTION: 1. When the headsets is turned on, the default connection is on 2.4GHz mode. 2. Insert 2.4GHz dongle to your device. The headsets will be automitically detected. C. BLUETOOTH CONNECTION 1.Press and hold the MODE button to switch to Bluetooth mode. 2.On your device, turn on the Bluetooth function, and set it to search for Bluetooth devices. 3.Select (WD-GT08) from the list of found devices. 4.When paired, the LED light blue. Note: During pairing, if the headets are not connected to a device within 5 minutes, they automatically turn off. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Microsoft Word 2010 Microsoft Word 2010