Installation Guide for Guangzhou V Solution Telecommunication Technology models including: V2804REW-RGW, V2804REWRGW, 2AVIF-V2804REW-RGW, 2AVIFV2804REWRGW, V2804REW-RGW Optical Network Unit, Optical Network Unit, Network Unit
Guangzhou V-Solution Telecommunication Technology Co., Ltd. V2804REW-RGW Optical Network Unit 2AVIF-V2804REW-RGW 2AVIFV2804REWRGW v2804rew rgw
1GE+3FE+WIFI EPON ONU Quick Installation Guide V2.0 Aug. 13, 2019 P01.030488 2 1GE+3FE+WIFI EPON ONU Quick Installation Guide_V2.0 1. Indicator and Interface Description 1.1 Product Picture Figure 1 1GE+3FE+WIFI EPON ONU 1.2 Application Chart 1.3 Panel Lights Figure 2 Application Chart Figure 3 Panel Lights 3 1GE+3FE+WIFI EPON ONU Quick Installation Guide_V2.0 LED Power Mark POWER Registration PON Optical signal LOS WiFi WPS Interface WiFi Pair LAN1 LAN2 LAN3 LAN4 Status Description On The device is powered up. Off The device is powered down. On The device is registered to the PON system. Off Device is not registered to the PON system. Blink Device registration is incorrect. Blink Device does not receive optical signals. Off Device has received optical signal. On WiFi is working Off WiFi is not working ON WIFI allow one key join On Port is connected properly (LINK). Off Port connection exception or not connected. Blink Port is sending or/and receiving data (ACT). Table 1 Panel Lights 1.4 Interface/button Panel Figure 4 Interface/button Panel Name PON LAN RST POWER Pair WiFi Function Connect to OLT by SC type fiber connector, single mode optical fiber cable. Connect PC or other devices with Ethernet port by Cat5 cable, RJ-45 connector. Press RST button over 10 seconds, onu restores factory default and reboot. Connect with power adapter. DC 12V, 1A. Press down WiFi pair button to begin pairing. Press down WiFi turn on/off button to enable/disable WiFi function. Table 2 Interface/button Panel 4 2. Packing List Contents EPON ONU Installation Guide 3. Certification 1GE+3FE+WIFI EPON ONU Quick Installation Guide_V2.0 Quantity 1 pcs 1 pcs Contents Power adapter Quantity 1 pcs 4. Hardware Installation Installation Environment Requirements ONU equipment must be installed in the interior, and to ensure the following conditions: Confirmation at the ONU installation at sufficient space to facilitate cooling machine. ONU suitable operating temperature of -5 ~ 55 , humidity 10% to 90%. Device workplace should avoid radio transmitters, radar stations, and high-frequency interference from power equipment. Equipment Installation 1. Installed on the desktop Place the ONU on a clean bench, this installation is relatively simple, you can observe the following operation: Ensure the smooth workbench. Around the device enough space for heat dissipation. Do not place objects on the device. 2. Mounted on the wall Observation ONU equipment chassis two cruciform recess, in accordance with the position of the groove, installed two screws in the wall. The original selected two mounting screws gently snap into recesses aligned. Slowly let go, so that the device under the support of the screw hanging on the wall. 3. Connect fiber, network cable and power adapter to the corresponding interfaces, and turn on the power of product. 5 1GE+3FE+WIFI EPON ONU Quick Installation Guide_V2.0 FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.vs Adobe PDF Library 11.0