Waterway Plastics – Pool & Spa Supplies
Installation Guide for Waterway models including: 400-6621, 672-7401, 810-0068-WAT.0425, 400-6621 Eco Kleer Cartridge Filter System, 400-6621, Eco Kleer Cartridge Filter System, Cartridge Filter System, Filter System, System
9 mag 2025 — Twist and separate as shown in Detail 7. ECO-KLEER CARTRIDGE FILTER SYSTEM OWNER'S MANUAL ... 400-6621. Universal Plug w/ O-Ring. 13. 672-7401. Eco-Kleer Base.
The Eco-Kleer. Cartridge Filter System features the exclusive 1-2-3 Safety Locking. System to ensure safe and simple filter maintenance. 1. Turn off pump ...
File Info : application/pdf, 5 Pages, 1.87MB
DocumentDocumentCARTRIDGE FILTER SYSTEM OWNER'S MANUAL ECO-KLEER CARTRIDGE FILTER SYSTEM OWNER'S MANUAL Our Eco-Kleer Cartridge Filter System is shipped from Waterway complete with everything you need right in the box. Assemble filter system only after above-ground pool is installed. Fill pool with water. Do not raise water level above pool return line. The pool equipment should be located between pool skimmer and return line. The filtration system should not be closer than 2 ft. and not further than 5 ft. from the pool. The Eco-Kleer Cartridge Filter System needs to be on a completely flat surface (e.g. patio block, cement slab, etc.). The pump will require a 110 volt/20 amp service. WARNING: A GFCI is required. Follow national and local building and safety codes. Before opening shipping carton, make sure box is in the upright position. Inside the carton, you will find: 1. One base 2. One pump (packaged in separate box) 3. One filter 4. Two lengths of 6 ft. hose 5. One bag with fittings INSTALLATION INSTRUCTIONS WARNING! READ ALL INSTRUCTIONS AND WARNING LABELS BEFORE OPERATING FILTER! 1. Place filter and base on a level, secure surface. Place the pump on the base to the left of the filter. The pump should now be facing the filter marked "Inlet". There is no need to disassemble filter or pump assemblies. 2. Open pump trap lid and remove 2" gasket. Place 2" gasket into union nut. Hand tighten union nut to suction side of pump (Detail 5). 3. Secure pump to the base using the snap pins (#18) provided (Detail 4). 4. Open fittings bag and remove coupling assembly (Detail 2). Assemble 2" gasket, coupling, coupling O-Ring, and 2" union nut, and thread into inlet side of filter. 5. Thread 2" union nut to pump discharge (Detail 3). Thread hose adapter with O-Ring, to pump trap suction side (Detail 1). 6. From the fittings package, remove 1 1/2" hose adapter and O-Ring (Detail 2). Thread into the outlet side of the filter tank. 7. Remove 4 hose clamps from the fittings bag. Select one of the hose lengths and slip one clamp over the end of hose adapter. Place the end of the hose onto the hose adapter (pump suction) and the other end to the hose adapter end of the pool skimmer. Repeat steps with filter outlet to pool return. 8. Remove the lid handle (#4a) from the fittings bag and attach it to the top of the lid assembly (#4) as shown (Detail 6). Secure filter to filter base using Phillips-head screws (#13a - 2), (Detail 7 & 8). Fill pool until water level is halfway up length of skimmer throat. 9. Open air release knob. Plug in and turn on pump. Air will pass out of the filter through the air release knob. Once water discharges from knob, close it. NOTE: To remove lid assembly, take off filter nut (#6), insert filter wrench (#9a) in notch between filter body (#9) and lid assembly (#4). Twist and separate as shown in Detail 7. 20 10 21 9 10 19 16 11 15 14 11 11 12 22 DETAIL 1 DETAIL 2 11 14 16 15 17 DETAIL 3 ECO-KLEER CARTRIDGE FILTER SYSTEM REPLACEMENT PARTS 4b Item Part No. Description 1 830-4000SS Pressure Gauge 4a 1a 519-7431 Pressure Gauge Fitting Adapter 1b 805-0117SD O-Ring 2 602-0201 Air Relief Plug 3 805-0207 O-Ring Air Relief 4 519-7407 4a 519-7601 Lid Assembly Large (150/200 sq. ft.) Lid Handle DETAIL 8 4b 819-9002 5 805-0460 #12 x 3/4" S/S Phillips Head Screw Lid O-Ring DETAIL 6 6 718-7251 Filter Nut (sold with Lid Assembly only) 6a 519-7451 Handle Assembly Lock Tab (2 required) 6 7 519-7441 7a 500-7360 7b 500-7350 Wing Nut Core Center Sub -Assembly 1/4" x 24" PVC Tubing with Screen & Tie 6 6a 6a 8 817-1150M 150 sq. ft. Cartridge 5 817-1200M 200 sq. ft. Cartridge 9a 9 515-7257 Body Filter Bottom 4 9a 519-7470 Filter Wrench (see Detail 7) 4a 4b 10 417-6151 1 1/2" MPT x 1 1/2" Male Smooth Hose Adapter 13a 419-3600 1 1/2" NPT Extended Coupler 11 805-0224 O-Ring 9 12 400-6621 Universal Plug w/ O-Ring 2 3 1 1a 1b 1c 13 672-7401 13a 819-0004 14 415-5001 Eco-Kleer Base #10 x 1" S/S Phillips Head Screw 2" Union Nut 4 13a 15 419-7241 Coupling DETAIL 7 16 711-4010 2" Union Gasket 7 17 PK1100 1 HP 1-Speed Hi-Flo Pump 7a PK1150 1 1/2 HP 1-Speed Hi-Flo Pump PK1200 2 HP 1-Speed Hi-Flo Pump 18 429-7221 Snap Pin 19 310-6500 6" Trap 1 1/2" Buttress x 2" Flange 20 319-3260 21 805-0436 6" Trap Lid O-Ring 8 7b 22 319-3230 6" Basket Assembly 23 872-9010 Hoses 24 WV001H Gate Valve -- 810-0068-WAT Instruction Sheet 10 22 21 10 20 9 18 16 10 11 22 21 16 11 15 14 11 12 19 11 22 18 13 18 17 19 DETAIL 4 DETAIL 5 18 17 13a (2) CLEANING INSTRUCTIONS If the pressure gauge on your filter reads 5 PSI or higher than the original starting pressure, the filter needs to be cleaned. The Eco-Kleer Cartridge Filter System features the exclusive 1-2-3 Safety Locking System to ensure safe and simple filter maintenance. 3. Press the yellow safety latch on the underside of the locking nut and turn the nut counterclockwise to remove the lid. Rinse the cartridge element with a garden hose. There is no need to remove the element from the filter. 1. Turn off pump. WARNING: Never attempt to clean filter while pump is running. This is a pressurized vessel. It could cause severe injury or harm to your person. Plug skimmer and pool return lines or drain pool water level to below pool return line. 2. Slowly open the air release knob on top of filter until the pressure gauge reads "0". Open drain cap at bottom of filter and allow water to flow. 4. Reassemble lid and follow start-up procedures from original instructions. My Original Starting Pressure is ________ PSI (Pounds per Square Inch). I should clean the filter at ________ PSI. LIMITED WARRANTY Waterway Plastics manufactures its products and equipment in accordance with very high standards of workmanship. We use the best materials available and maintain the highest quality procedures practical in the industry. In accordance, Waterway warrants its products as follows: Warranty only applies to OEMs and Distributors of Waterway. © 2025 Waterway Plastics 810-0068-WAT.0425 INSTALLATION INSTRUCTIONS FOR ATTACHING ECO-KLEER FILTER LID HANDLE AND REMOVAL OF LID ASSEMBLY 819-9002 (2) 519-7601 Using a Phillips-head screwdriver, screw the two (2) provided Phillips-head screws through the handle assembly and into the filter lid, as shown. Make snug; DO NOT overtighten. TO REMOVE LID ASSEMBLY: Remove lock-nut assembly. Insert wrench in notch between filter body and lid assembly as shown. Twist wrench to separate. INSTALLATION INSTRUCTIONS FOR ATTACHING ECO-KEER FILTER BODY TO THE ECO-KLEER FILTER BASE 1. Align the drain port of the filter body to the base as shown. 2. Use one of the two self-threading screws provided. Screw it into the filter body as shown. 3. Using the other self-threading screw, screw it into the filter body on the opposite side. 4. Continue the installation of the filter according to the filter instructions. Designed, Engineered & Manufactured in the USA. ©2025 Waterway Plastics WARRANTY For product registration visit: www.waterwayplastics.com. For Warranty questions or claims please contact point of purchase. 810-0212-EFS.0425