2022-03-17 — Perform RCM reprogramming after the winch has been installed. WARNING: Failure to follow these instructions could result in personal injury or death: ○ ...33 puslapiai
Texas - 21-22 Ford Bronco Warn Winch Mount w/ Bull Bar (Incomplete/Missing Parts) $300 obo | Bronco6G - 2021 Ford Bronco & Bronco Raptor Forum, News, Blog & Owners Community
3/17/22, 8:12 AM 2021 Bronco TECHNICAL SERVICE BULLETIN Equipped With Parking Aid Senso rs - Parking Aid Sensors Not Staying Deactivated After Vehicle Is Off Longer Than 5 Minutes 22-2094 15 March 2022 This bulletin supersedes 22-2038. Model: Ford 2021-2022 Bronco Summary This article supersedes TSB 22-2038 to update the Service Procedure. Issue: Some 2021-2022 Bronco vehicles equipped with parking aid sensors may exhibit a park aid system that does not remain deactivated after the vehicle has been off for more than 5 minutes. The vehicle may exhibit false alerts from the parking aid warning system which may cause it to activate while driving or towing or due to the presence of a winch. This may be due to the software within the instrument panel cluster (IPC). To correct the condition, follow the Service Procedure and update the IPC software. Action: Follow the Service Procedure steps to correct the condition on vehicles that meet all of the following criteria: · 2021-2022 Bronco · Equipped with parking aid sensors · Parking aid sensors do not stay deactivated if vehicle remains in the off position for longer than 5 minutes Warranty Status: Eligible under provisions of New Vehicle Limited Warranty (NVLW)/Service Part Warranty (SPW)/Special Service Part (SSP)/Extended Service Plan (ESP) coverage. Limits/policies/prior approvals are not altered by a TSB. NVLW/SPW/SSP/ESP coverage limits are determined by the identified causal part and verified using the OASIS part coverage tool. Labor Times Description Operation No. Time 2021-2022 Bronco: Reprogram The IPC, Refresh The Parking Aid System And Road Test (Do Not Use With Any Other Labor Operations) 222094A 3.0 Hrs. 2021-2022 Bronco: Reprogram The IPC, Refresh The Parking Aid System And Road Test 222094B 3.3 Includes Time To Disconnect/Reconnect Battery And A Second Road Test (Do Not Use With Any Hrs. Other Labor Operations) Repair/Claim Coding Causal Part: 10849 Condition Code: 04 Service Procedure NOTE: If a MyKey has been programmed to the vehicle, use the admin key to operate the vehicle throughout this procedure. 1. Reprogram the IPC using the latest level of the Ford Diagnosis and Repair System (FDRS) scan tool. NOTE: IPC programming could take up to 3 hours if using a VCM 3 or VCMM and up to 6 hours if using a VCM 2, however, no technician interaction is needed during programming. https://www.fordtechservice.dealerconnection.com 1/2 3/17/22, 8:12 AM 2021 Bronco 2. Refresh the park aid system by cycling all parking aid sensors from on to off, several times, ending in off. Use the touchscreen to access Features > Driver Assistance > Parking Aid Sensors. 3. Turn the vehicle off and let sit undisturbed for at least 5 minutes. 4. Test drive the vehicle to be sure that all parking aid sensor warning chimes remain deactivated when obstructions are in close proximity to the rear and front bumpers (if equipped). NOTE: Vehicle must be in drive (D) or reverse (R) to activate the appropriate parking aid sensor chime. 5. If the park aid system fails to remain disabled, disconnect the vehicle's 12v battery for at least 5 minutes, reconnect the battery and repeat Step 4. © 2022 Ford Motor Company All rights reserved. NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by "do-it-yourselfers". Do not assume that a condition described affects your car or truck. Contact a Ford or Lincoln dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supersede this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources. https://www.fordtechservice.dealerconnection.com 2/2 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS PRIOR TO INSTALLATION READ THESE INSTRUCTION COMPLETELY For questions, Call the FORD PERFORMANCE Techline 1-800-367-3788 Please visit https://www.performanceparts.ford.com for warranty information Warn Winch Kit A B C x1 x1 x1 D E F x1 x2 x1 G H I J K x1 x6 x1 x1 x1 L M N O x1 x2 x6 x1 P QR S x1 x4 T U V x1 x1 W x1 x2 x2 x2 Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 1 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS X Y Z x4 x4 a1 x1 b1 c1 d1 e1 x1 f1 x6 x2 x1 x1 x1 Tools Required T-30 15 MM 10 MM 8 MM STUD FOR T-30 MISS5/I8N" G NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 2 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS Kit Contents A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a1 b1 c1 d1 e1 f1 Description Clevis Bracket (Left Hand) Clevis Bracket (Right Hand) CAC Bracket (Left Hand) CAC Bracket (Right Hand) Inner Frame Bolt Inner Frame Bracket (Right Hand) Outer Frame Bracket (Left Hand) Frame Bracket Nut - M10 HX PTM FL 10 Inner Frame Bracket (Left Hand) Outer Frame Bracket (Right Hand) Frame Nut Plate (Left Hand) Frame Nut Plate (Right Hand) Recovery Forging Outer Frame Bolt - M12x1.75x80.0 HEX FLNG PIL Recovery Forging Bracket (Left Hand) Recovery Forging Bracket (Right Hand) Recovery Forging Bracket Bolt - M12X30 HF PIL 10 Winch Plate Fair Lead License Plate Kit (Optional) Fairlead Bolt - 7/16-14 HX Fairlead Washer - 7/16 HELIX SPLIT Fairlead Nut - 7/16 ACORN Winch Winch Housing Nut - M10 Winch Housing Bolt - M10 X 35 Brush Bar Brush Bar Nut - M10 HX PTM FL 10 Nut - M6 HF 8 Hook Hook Strap Winch Remote Part Number N2DB-19E515-BA N2DB-19E515-CA N2DB-19E518-CA N2DB-19E518-FA N2DB-19H381-AA N2DB-19E518-DA N2DB-19E518-AA W716805-S442 N2DB-19E518-BA N2DB-19E518-EA N2DB-17B757-AA N2DB-17B756-AA N2DB-19E515-AA W500747-S450B N2DB-19H292-BA N2DB-19H292-CA W500642-S405B N2DB-19H292-AA N2DB-19E514-AA KN2DB-17N397-AA WARN-1824 WARN-2146 WARN-73849 N2DB-19E513-AA WARN-87166 WARN-69954 W716805-S450B W520412-S437 N2DB-19H382-AA LC3C-19H380-AA Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 3 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS INSTALLATION PROCEDURE - Winch Kit IMPORTANT: After winch installation ensure the warning label is installed under the mounting plate. See illustration below Restraint Control Module (RCM) programming is required after winch installation to ensure the vehicle systems function properly. Perform RCM reprogramming after the winch has been installed. WARNING WARNING: Failure to follow these instructions could result in personal injury or death: Installation instructions must be followed to ensure correct fitment to the vehicle and proper operation of the accessory. When this winch is fitted, and again if this winch is removed, a software update must be performed by a Ford dealer. Failure to follow this instruction may affect the performance of the vehicle's safety systems, including the airbags. This product and its fixing installation must not be modified. No accessory or fitment shall extend beyond the front of the vehicle. This product was specifically designed for this vehicle. Do not use in any other vehicle. M2DA-25729-AA 1. Remove the retainers and the skid plate. 15 MM STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 4 of 31 PLACE COPY HERE IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 2. Remove the push pin retainers. 3. Remove the front bumper trim panel. STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 5 of 31 IS M-1821-B 112221 STUD FOR M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 4. If Equipped, remove the bolts and the safari bar. 5. Install the safari bar retainers into the front bumper. · Torque: 25 Nm (18 ft-lb) ! 25 Nm (18 ft-lb) STUD FOR MISSING NUT STUD FOR MISSING NUT STUDT-30FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 6 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS NOTE: Save front bumper bolts for installation. 6. Remove the front bumper bolts. 15 MM NOTE: If the bumper is equipped with a safari bar it must be removed before proceeding. The mounting bolts should be reinstalled and torqued to 18 lb.ft (25 Nm). 7. Remove the front bumper. STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 7 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 8. Remove the retainers and the front license plate mounting bracket. 8 MM 9. Remove the recovery hook holding bolts. 10 MM STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 8 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 10. Remove and discard the recovery hooks. 11. Remove the plastic holding nuts on both sides of the vehicle. STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 9 of 31 IS MS-T1U8D21F-OBR112221 MISSING NUT M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 12. Remove and discard the frame nut plate on both sides of the vehicle. 13. Install the two clevis brackets to the bumper. · Torque: 10.5 Nm (7.5 ft-lb) ! 8 MM 10.5 Nm (7.5 ft-lb) STUD FOR MISSING NUT STUD FOR MISSING NUT SMBTISUSDINFGORNUT PLACE COPY HERE A PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 10 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS NOTE: Save frame bolts for installation (*). 14. Remove the two frame bolts. Perform this step on both sides. 15 MM 15. Install the winch CAC bracket and the bolts saved from step 14 to the frame. 15 MM ! 80 Nm (59 ft-lb) D * C STUD FOR MISSING NUT * STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.comPLACE COPY HERE Techline 1-800-367-3788 Page 11 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 16. Install the shoulder bolt into the frame rail. Perform this step on both sides of the vehicle. E 17. Install the left hand inner and outer bracket to the frame rail. Hand tighten the nuts at this time. F H G H STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 12 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 18. Install the right hand inner and outer bracket to the frame rail. Hand tighten the nuts at this time. J H I H 19. Install the frame rail bracket. K L STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.comPLACE COPY HERE Techline 1-800-367-3788 Page 13 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 20. Starting by hand, install the plastic holding nuts. Perform this step on both sides. · Torque: 10 Nm (7 ft-lb) ! 10 Nm (7 ft-lb) 21. Tighten all 4 inner and outer brackets nuts. · Torque: 48 Nm (35.5 ft-lb) H 15 MM H STUD FOR !MISSING NUT STUD FOR MISSING NUT 48 Nm (35.5 ft-lb) STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com PLACE COPY HERE Techline 1-800-367-3788 Page 14 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 22. Install the front bumper and connect the electrical connector. F F NOTE: Bolts saved from step 6. 23. Install the front bumper retainers. · Torque: 80 Nm (59 ft-lb) ! 15 MM B 80 Nm (59 ft-lb) A STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 15 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 24. Install the clevis bracket nuts. · Torque: 35 Nm (25.8 ft-lb) C A ! 35 Nm (25.8 ft-lb) H B 15 MM D 25. Install the recover forging into the clevis bracket. · Torque: 110 Nm (81 ft-lb) 15 MM ! 110 Nm (81 ft-lb) M STUD FOR MISSINGNNUT M STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.comPLACE COPY HERE Techline 1-800-367-3788 Page 16 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 26. Install the front bumper trim panels. 27. Install the front bumper trim panel push pins. STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 17 of 31 ISMMSIST-S1UI8DN2GF1O-NBRU1T12221 STUD FOR M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 28. Install the recovery forging mounting bracket. · Torque: 80 Nm (59 ft-lb) P O Q Q 15 MM ! 80 Nm (59 ft-lb) NOTE: Installation of license plate bracket is optional depending on local regulations. 29. Install the fairlead to the winch plate. · Torque: 47.5 Nm (35 ft-lb) T S V W 5/8" U !STUD FOR MISSING NUT R STUD FOR 47.5 NmM(3I5SfSt-lbIN) G NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 18 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 30. If equipped, install the license plate to license plate mounting bracket retainers. Not Included Not Included Not Included 10 MM Not Included T T-30 R 31. Install the winch mounting nuts into the winch housing slots. X Y Y STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 19 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 32. Route the winch rope through the fairlead and install the winch to the winch plate. · Torque: 47.5 Nm (35 ft-lb) X X R Z Z 33. Engage the winch wire harness push pin retainers into the winch plate. X 15 MM R ! 47.5 Nm (35 ft-lb) R STUD FOR MISSING NUT R STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com PLACE COPY HERE Techline 1-800-367-3788 Page 20 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 34. Install the brush bar to the winch plate. a1 R 35. Install the brush bar outboard nut. · Torque: 47.5 Nm (35 ft-lb) a1 R ! b1 47.5 Nm (35 ft-lb) STUD FOR MISSING NUT STUD FOR MISSINbG1 NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 21 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 36. Install the winch assembly to the recovery forging mounting brackets. · Torque: 47.5 Nm (35 ft-lb) X a1 R 15 MM b1 37. Remove the lug nuts and the left hand tire. ! b1 47.5 Nm (35 ft-lb) STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT Ford Factory Shop Manual purchase options www.motorcraftservice.comPLACE COPY HERE Techline 1-800-367-3788 Page 22 of 31 IPSLMAC-1E8C2O1-PBY1H1E2R22E1 PLACE COPY HERE M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 38. Remove the retainers and the left hand wheel well splash shield. 39. Route the positive battery cable under the winch plate and through the left hand side of the center bumper opening. Route the negative cable over top of the left hand recovery forging. + - STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 23 of 31 PLACE COPY HERE IS M-1821-B 112221 PLACE COPY HERE M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 40. Route the positive cable through the frame towards the left hand side of the vehicle. + STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 24 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 41. Route the positive and negative cables upwards towards the battery. Secure the cables to the existing wiring harness using tie straps. + - STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 25 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 42. Open the hood of the vehicle. 43. Connect the positive winch cable to the positive bus bar on the vehicles battery. · Torque: 13.5 Nm (10 ft-lb) c1 10 MM ! STUD FOR + MISSING NUT 13.5 Nm (10 ft-lb) STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 26 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 44. Connect the negative winch cable to the negative terminal on the vehicles battery. · Torque: 13.5 Nm (10 ft-lb) 10 MM c1 ! - 13.5 Nm (10 ft-lb) 45. Install the tow hook and tow hook strap to the winch cable eyelet. d1 STUD FOR e1 MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.comPLACE COPY HERE Techline 1-800-367-3788 Page 27 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 46. Connect the remote to the winch and test the operation. Store the winch remote in the center console. 47. Close the hood of the vehicle. STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 28 of 31 IS M-1821-B 112221 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 48. Install the left hand wheel well splash shield and retainers. 49. Install the left hand tire and lug nuts. STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com PLACE COPY HERE Techline 1-800-367-3788 Page 29 of 31 ISPMLA-C1E82C1O-BPY11H2E2R2E1 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 50. Install the left hand wheel well splash shield and retainers. · Torque: 30 Nm (22 ft-lb) 15 MM ! 30 Nm (22 ft-lb) Programming procedure: 51. Connect Ford Diagnostic & Repair System (FDRS) and start a new vehicle session. 52. Select "Toolbox", then scroll down to "RCM - Restraint Control Module". On the left hand side of the screen download the "RCM - Winch Configuration" 53. Select "Run" after the download has completed. Follow the on-screen instructions to complete the RCM - Winch Configuration. NOTE: When prompted for part number entry, enter "M-1821". The part numbers are case sensitive. Do Not enter spaces or a part suffix or quotes. 54. If equipped with Front Bumper Park Aid Sensors, disable Park Aid Front Sensors. Press `Features' on the SYNC touchscreen, press `Driver Assistance', then select `Park Aid Front Sensors' to OFF. STUD FOR MISSING NUT STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 30 of 31 IPSLMAC-E18C2O1P-BY 1H1E2R2E21 M-1821-B 2021 Bronco Off-Road Winch NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS Returning Vehicle to Factory Condition: When completely removing the Winch from the vehicle, perform these steps to return the vehicle to factory conditions. Programming is required to reset the airbag safety system sensitive for proper deployment during a collision event. 55. Connect Ford Diagnostic & Repair System (FDRS) and start a new vehicle session. 56. Select "Toolbox", then scroll down to "RCM - Restraint Control Module". On the left hand side of the screen download the "RCM - Winch Configuration" 57. Select "Run" after the download has completed. Then select "Remove Winch from Vehicle" and follow the on-screen instructions to complete the RCM Winch Configuration. NOTE: During the programming procedure you will be prompted to enter the part number "RESTORE". The part numbers are case sensitive and do not include any spaces. 58. If equipped with Front Bumper Park Aid Sensors, Enable Park Aid Front Sensors. Press `Features' on the SYNC touchscreen, press `Driver Assistance', then select `Park Aid Front Sensors' to ON. Ford Factory Shop Manual purchase options www.motorcraftservice.com Techline 1-800-367-3788 Page 31 of 31 IS M-1821-B 112221iText 2.1.5 (by lowagie.com)