Elevoc Clear True Wireless Stereo Earphones User Manual

Product Description and Accessories

Operating Instructions

Power On/Off

• Power On: Open the charging case. The earphones will automatically power on.
• Power Off: Place the earphones into the charging case and close the case cover. The earphones will automatically power off.

Initial Bluetooth Connection

1. Open the charging case. The earphones will automatically enter pairing mode (ensure the charging case has sufficient power).
2. On your device, turn on Bluetooth settings and connect to "Elevoc Clear".

Pairing with Other Devices

1. Place both left and right earbuds into the charging case, keeping the case cover open.
2. Press and hold the charging case button for 5 seconds. The indicator lights will flash alternately, then emit a constant light for 3 seconds, indicating the earphones have entered Bluetooth searching and pairing mode.
3. Connect the device according to the Bluetooth connection mode.

Charging

Charging the Earphones

Place the earphones into the charging case. They will begin charging automatically. The left and right indicator lights on the charging case will flash continuously until the earphones are fully charged. A low-battery tone will sound if the battery level is below 20%.

Charging the Charging Case

Open the charging case cover. The constant light from the indicator lights reflects the current charge level. Plug a Type-C charging cable into the charging port. The 4 indicator lights will flash continuously according to the charging status. The lights will emit a constant light when fully charged.

[Diagram: Charging case LED indicators showing battery levels: 0-25%, 26-50%, 51-75%, 76-100%]

[Diagram: USB Type-C charging cable connection, 5V=1.0A]

Touch Commands

Operate the device using touch commands. Left (L) and Right (R) earbuds perform the same functions.

Music Mode

• Play / Pause Music: Single tap L/R
• Next Song: Double tap L/R
• Previous Song: Triple tap L/R

Call Mode

• Receive Call: Single tap L/R
• Decline / Cancel / End Call: Double tap L/R

Switch Modes

Press and hold L/R for 2 seconds to toggle between ANC (Active Noise Cancellation), Ambient, and Default modes.

Restore Factory Settings

1. Remove the earphone device listing from your phone's Bluetooth settings.
2. Place the earphones into the charging case.
3. With the case cover open, press and hold the charging case button for 10 seconds. The 4 indicator lights on the charging case will stop flashing and then emit a constant light for 3 seconds.
4. Close the case cover to complete the reset.

[Diagram: Press and hold case button for 10 seconds]

Care and Maintenance

To comply with warranty terms and extend product life, please follow these suggestions:

• Avoid exposing the product to excessively high temperatures, which can shorten component lifespan, damage the battery, and deform plastic parts.
• Avoid exposing the product to excessively low temperatures to prevent damage to internal circuitry.
• Do not disassemble the product unless performed by professionals, as this may cause damage.
• Do not drop, shake vigorously, or hit the product with hard objects to avoid damaging internal circuitry.
• Clean the product with a soft, dry cleaning cloth. Do not use harsh chemicals or cleaning agents.
• Do not use sharp objects to scratch the product surface, to avoid damaging the outer shell or appearance.

Safety Precautions

• For personal safety, avoid wearing or placing earphones too near a pacemaker (less than 10 cm).
• This product is not a toy. Children should only use this device under adult supervision.
• Using earphones at high volume, especially for extended periods, may result in hearing damage.
• A sharp sound may be emitted when switching high-fidelity audio on/off or plugging in earphones. Adjust volume to the lowest setting before switching audio sources or plugging in earphones.
• For traffic safety, refrain from using earphones while driving or cycling.
• Exercise caution or suspend ANC mode use in potentially dangerous situations.

⚠️ Warning! (Battery Safety)

• Improper battery replacement may risk explosion. Use only new batteries of the same or equivalent type.
• For products with removable batteries, they must be recycled or disposed of appropriately. For products with non-removable batteries, do not disassemble the battery.
• Do not disassemble, apply heavy impact, compress, or throw the battery into fire. Avoid exposing the battery to conductive materials, liquids, fire, or high temperatures.
• Do not let battery terminals contact metal objects. Cease use if there is expansion, leakage, discoloration, odor, or any other abnormality.
• Do not use the battery if it has been immersed in water.
• Improper battery handling may result in explosion or leakage, causing burns or other bodily harm.
• In case of battery leakage, take precautions and dispose of the battery immediately according to local laws and regulatory requirements.

After-sales Service

Thank you for choosing Elevoc Clear earphones. Elevoc offers a one-year warranty service. For user benefits or support, contact: support@elevoc.com.

Regulatory Compliance

Note: This product has been tested and conforms to Class B digital device requirements per FCC Rules Part 15. These restrictions aim to provide reasonable protection and prevent harmful interference in residential installations. If instructions are not followed, radio frequency radiation may cause harmful interference. This does not guarantee interference will not occur. If harmful interference with radio or visual reception occurs, try shutting down and turning on the device. Users are encouraged to try one or more of the following measures:

• Relocate or reposition the receiving antenna.
• Increase the distance between the device and the receiver.
• Connect the device to a circuit outlet different from the receiver connection circuit. Consult your dealer or an experienced radio/television technician.

Changes or modifications not explicitly approved by Elevoc may revoke user permission to operate the device.

This device conforms to FCC Rules Part 15 and license-exempt RSS standards of the Canadian Department of Industry. Device operation must meet two criteria: 1) No harmful interference. 2) Accept all received interference, including that which may cause undesired operation. The device conforms to FCC and Canadian exposure limits for the general population. It shall not be operated with other antennas or transmitters.

FCC ID: 2A2EV-CLEAR

Model: Elevoc Clear

Technical Regulations for Low-Power Radio-Frequency Devices

Article 12 (NCC - Taiwan)

In accordance with "Low-power Radio-frequency Devices Technical Regulations", no companies, enterprises, or users shall alter frequency, enhance emission power, or modify original design characteristics and functions without NCC permission.

Article 14

Low-power radio-frequency devices shall not affect aircraft safety or interfere with authorized communication. Upon detection, users must immediately cease usage until interference stops. Authorized communication refers to radio communications operating under the Telecommunications Regulations of the People's Republic of China.

ISED Statement (Canada)

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation. The digital apparatus complies with Canadian CAN ICES-3(B)/NMB-3(B).

IC: 27399-CLEAR

RF Exposure Information

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

CE Compliance (Europe)

Elevoc declares that this product conforms to the basic requirements of the Radio Equipment Directive 2014/53/EU, other relevant regulations, and applicable EU directives.

Europe: Use within the frequency band 2400 to 2483.5 MHz.

• Bluetooth: Maximum emission power less than 20 dBm ERP.
• Bluetooth Low Energy: Maximum power spectral density less than 10 dBm/MHz EIRP.

[Bluetooth Logo] The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG. All such marks are used by Elevoc under license.

Company: E-CrossStu GmbH

Address: Felix-Dshn-Str 4, 70597 Stuttgart

Email: E-CrossStu@web.de

[EC REP Logo]

Japanese Radio Device Compliance

[Japanese Radio Device Compliance Mark: R 210-161621] This product conforms to the requirements of Japanese radio devices.

Battery Disposal

Please dispose of used batteries in accordance with local regulations. Do not incinerate.

[Recycling Symbol] This symbol indicates that this product shall not be disposed of as household waste and must be delivered to an appropriate collection facility for recycling. Proper disposal and recycling contribute to the conservation and protection of natural resources, human health, and the environment. For more information, contact your local municipality or the store where you purchased the product. Removal of the rechargeable lithium-ion battery must only be done by qualified professionals.