mailto:info@showven.cn
Founder of Sparkular, Sparkular Machine Maker | Showven
User Manual for SHOWVEN models including: CREEPER ICE PLUS, CREEPER ICE, CREEPER ICE PLUS Creeper Ice Dry Ice Machine, CREEPER ICE PLUS, Creeper Ice Dry Ice Machine, Ice Dry Ice Machine, Dry Ice Machine, Ice Machine, Machine
Download List - SHOWVEN
Dry ice gives off carbon dioxide gas, which may cause difficulty breathing or suffocation. So please make sure the space is well ventilated before operate ...
File Info : application/pdf, 12 Pages, 639.64KB
DocumentDocumentUSER MANUAL CREEPER ICE dry ice machine V1.2 2024/06/24 CREEPER ICE PLUS CREEPER ICE SHOWVEN Technologies Co., Ltd. Thanks for choosing SHOWVEN® CREEPER ICE series dry ice machine, we wish it will bring you lots of exciting moments. Please read the following manual carefully before operating this product. SAFETY CONSIDERATIONS \ Unauthorized repair are prohibited, it may cause serious incident \ Never store dry ice in sealed container, it may explosion due to dry ice sublimates to carbon dioxide gas. \ Never cover or block the nozzle when operation to avoid explosion due to the generation of carbon dioxide gas. \ Wear thick gloves when handling dry ice, do NOT handle with bare hands. \ Do NOT swallow dry ice, it may lead to severe injuries. \ Before breaking the dry ice, cover it with a piece of cloth or place it in a cloth bag, do wear protective goggles. \ Dry ice gives off carbon dioxide gas, which may cause difficulty breathing or suffocation. So please make sure the space is well ventilated before operate CREEPER ICE machine, do NOT use in confined space. \ Make sure power supply in consistent with the rated voltage of the equipment, and the socket must well grounded. Unplug and turn off the machine when not use. \ The output nozzle is very hot when machine is running, do NOT touch it. Keep a minimum distance of 2m from the nozzle to nearest object. \ Do NOT use the product as a space heater. \ Always disconnect the power connection before cleaning. \ Empty the water tank before transport or storage the machine. \ For safety reasons, please operate the product on horizontal ground only. Lock wheels to keep from moving. \ Use clean water as impurities may result in damage to the machine. \ Do not operate product in ambient temperature higher than 50 . \ Always install the machine in well ventilated place, at least 50cm space around the machine. Do NOT cover the nozzle. \ For adult use only, keep it away from children, fire, inflammable and explosive articles. \ The area in front of machine may become wet during operation. Be aware of the slip ground. \ If the machine fails to work, please stop operation and unplug the machine. Check fuse, power cable and socket etc. carefully, if can't solve the problem, please contact SHOWVEN® (info@showven.cn) or your local SHOWVEN partner for advise. Foreword Thanks for choosing SHOWVEN® CREEPER ICE series dry ice machine. Please read following manual carefully and completely before operating this product. Operate according to instructions is very important for safety, and can elongate the service life of the machine. Functional Characteristics \ Molded enclosure, lighter, durable and rustless. \ Water spray design, fast ON/OFF, dry ice saving \ No mechanical lifting structure, better stability \ Huge ice and water reservoir, supporting long effects time \ Continuous variable fog output adjustment, meet different application scenario \ Water tank and ice basket separate design, longer ice storage time, achieve multi use with single ice feeding \ Dual or triple heating system, flexible power switch meet different power supply \ Abrasion-resistant silent caster \ Easier residual water drainage \ Rain-proof structure Technical Specifications \ Model: CREEPER ICE PLUS \ Dimension: 642x584x887mm \ Packing Dimension: 677x619x826mm \ Voltage: AC220-240V, 50/60Hz AC100-120V, 50/60Hz \ Fuse: Breaker 3P 20A \ Work power: 3000W/9000W (230V) 1600W/4800W (120V) \ Heating Up Time: Appr. 40min @9000W ppr. 70min @4800W \ Dry Ice Capacity: 30kg \ Water Tank Capacity: 75L \ DMX-512: yes \ Wireless Control: yes \ Output Volume Adjustment:50%-100% \ Max. Coverage Area: Appr. 800 \ Cumulative Output Time: 5-10min \ Consumable: Dry ice, Water \ Net. Weight: 45kg \ Gross Weight: 68kg CREEPER ICE 492x584x760mm 527x619x726mm AC220-240V, 50/60Hz AC100-120V, 50/60Hz Breaker 20A 3000W/6000W (230V) 1600W/3200W (120V) Appr. 30min @6000W ppr. 50min @3200W 15kg 55L yes yes 50%-100% Appr. 500 5-10min Dry ice, Water 35kg 50kg Product Overview CREEPER ICE PLUS 1. Upper Cover 2. Upper Cover Lock 3. LCD and Function Buttons 4. 3-pin XLR 5. Industrial Power Socket 6. Water Level Indicator 7. Drain Valve 8. 5-pin XLR 9. Air Switch 10. LED Indicator x3 11. Fog Outlet 1. Upper Cover 2. Upper Cover Lock 3. LCD and Function Buttons 4. LED Indicator x2 5. Fuse x2 6. Water Level Indicator 7. Auxiliary Power Input 8. Main Power Input 9. Drain 10. 5-pin XLR 11. 3-pin XLR 12. Fog Outlet CREEPER ICE Operation Panel 1. Control button area MENU: switch through setup menu; +: parameter up, multiplex "TIMER" (Timer Fog output when in main interface); -: parameter down, multiplex "VOLUME" (Continuous Fog output when in main interface); ENTER: confirm and save parameters (screen will blink once when save successfully); multiplex "STOP". NOTE: Screen will switch to main interface automatically if not press any button in 15s. Interface 1. Main interface: First Line: DMX address and Fog Output Volume, ":"blinks when there is DMX in signal. Second Line: water temperature, when temp. reached set temp. it will shows "READY"means the machine is ready to firing, press "VOLUME"to generate fog. 2. Error Information: Error information E1 No Water E2 Temp. Sensor E5 K Temp. Over E6 Heat Fail Explanation Filling the water tank Temp. Sensor loose or sensor cutting out Circuit board malfunction Heater broken or circuit board malfunction. 3. Setting Menu Press "MENU" switch through setup menu. Items Value DMX Address 1~511 TemperaturSet 60-80° Volume Out Wireless Set Language 50-100% ON / OFF /English Explanation DMX address setup Water TEMP. Set, the higher the temp. the longer the fog output Fog output volume increase as the value increase Wireless function set Language switch DMX Control channel CH1 Function 1~5: Fog off 6~255: Fog volume adjustment, fog volume increase from 50% to 100% Wireless Control Wireless control is used to remote control the machine. Before use the wireless function please make sure machine was ready, wireless status was ON, and no DMX cable connection. Remote controller: A. Fog output START B. Fog output STOP If the wireless remote is not working, please check the wireless function setup on machine. Press "MENU" find "wireless control" switch it into "ON", press "ENTER" to save the setup. Remote control match with machine was also in this interface, press any key on remote control for 1s, the LCD screen will blink once, means the match was successful. NOTE: Remote controller is optional configuration. You can buy it separately from SHOWVEN or SHOWVEN® authorized partners. Operation 1. Installation Check the machine and accessories, ensure it is in good status. Place the machine on a flat surface, tilting may result in inaccurate water level alarm. Lock wheels to keep from moving. Due to there are a huge amount of hot water inside machine, please do make sure the machine are firmly installed. 2. Fill the machine with water Open the upper cover and filling the machine with water until reached the Max. water level. CREEPER ICE water tank is 55L, CREEPER ICE PLUS is 75L. 3. Power ON Creeper ICE Connect the machine to suitable rated power supply. Please ensure power supply meets the requirement. Always connect the machine to a protected circuit and ensure it is properly grounded. CREEPER ICE with dual power supply design, users can use single or dual power to heating up. Whenever in single or dual power mode, the main power input must connected, the corresponding LED indicator will light up when power supply connected successfully. CREEPER ICE PLUS use industrial power socket. Turn on the air switch when power connected, and the LED indicator will light up. 4. Fill the machine with dry ice Open the upper cover, put the dry ice into basket. Close the upper cover and lock it. If filling the ice basket outside of machine, please make sure it well fitted when put it back to machine. Wear thick gloves and wear protective goggles when handling dry ice, do NOT handle with bare hands. 5. Setting and Firing When machine was ready, water reached set temp., press "VOLUME" of the machine will start to work. When water temp. lower than 30 , machine will stop working automatically, operator can also press STOP to stop the machine. If use DMX console control, please set DMX address and connect with DMX console (such as FXcommander) via DMX cable, and firing by follow the previously introduced DMX channel information. 6. Power OFF and clean up To turn off the machine, please POWER OFF and unplug the power cable. Please empty the dry ice basket. Make sure that the remaining dry ice is disposed of in accordance with local regulations and is not accessible to children or other unrelated persons. If need to transport the machine after show, please drain the remaining water when it is cool down. Please be aware of the hot water. Product Package CREEPER ICE Main unit x 1unit Power Cable x 2 pieces User Manual x 1 piece Fog vent hose 3.3m x 1piece Flight case package CREEPER ICE PLUS Main unit x 1unit Power Cable x 1 pieces User Manual x 1 piece Fog vent hose 3.3m x 2 pieces Fog vent head x 2 pieces Flight case package Caster Installation Please install the caster according to below schematic diagram. The brake wheel must installed in specific position accordingly. CREEPER ICE PLUS CREEPER ICE Maintenance 1. Running the machine at least once per month. 2. Clean machine regularly avoid dust, liquid accumulate on the machine. 3. Whenever storage or not use the machine for a period of time, please drain the machine and keep it dry. Warranty Instructions \ Sincere thanks for your choosing our products, you will receive quality service from us. \ The product warranty period is one year. If there are any quality problems within 7 days after shipping out from our factory, we can exchange a brand new same model machine for you. \ We will offer free of charge maintenance service for machines which with hardware malfunction (except for the instrument damage caused by human factors) in warranty period. Please don't repair machine without factory permission. Below situations NOT included in warranty service: \ Damage caused by improper transportation, usage, management, and maintenance, or damage caused by human factors; \ Disassemble, modify or repair products without permission; \ Damage caused by external reasons (lightning strike, power supply etc.) \ Damage caused by improper installation or use; For product damage not included in warranty range, we can provide paid service. Invoice is necessary when applying for maintenance service from SHOWVEN®. Showven Technologies Co., Ltd. Tel: +86-731-83833068 Web: www.showven.cn E-mail: info@showven.cn Add: No.1 Tengda Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, 410300, P.R.China