Street Aero
Installation Guide for STREET AERO models including: 2010-2013 Chevrolet Camaro 2SS Dual Exhaust, 2010-2013, Chevrolet Camaro 2SS Dual Exhaust, Camaro 2SS Dual Exhaust, 2SS Dual Exhaust, Dual Exhaust, Exhaust
2010-2013 Chevrolet Camaro 2SS (Dual Exhaust) Rear Diffuser – Street Aero
2010-2013 Chevrolet Camaro 2SS (Dual Exhaust) - Rear Diffuser – Street Aero
Instruction Manuals – Street Aero
File Info : application/pdf, 2 Pages, 429.60KB
DocumentDocumentSTEP: 1 Carefully place Fin 1 and Fin 2 onto the Main Panel (Match the number on the Fin to the number on the Main Panel) Secure with Small Bolt and Small Nut Small Bolt Small Nut 2 Small Nut x4 STREET AERO 1 2 Small Bolt x4 1 STEP: 2 Remove the OEM Washer Bolt and Clip from the two center bumper fin OEM Clip & OEM Washer Bolt 1 STEP: 3 Mount the assembled Main Panel to the bumper by securing Mounting Bracket CT-8 to the OEM mounting hole on STEP: 2 with M6 55mm Bolt, Finishing Washer, Washer, and Nut NOTE: Reach under to place Washer and Nut inside the bumper Align Mounting Bracket CT-7 and CT-9 to its correct location then Mark and Pre-Drill into the bumper NOTE: Use the hole on top of CT-7 and CT-9 to mark the drill location NOTE: Main Panel and Mounting Bracket may need to be removed before pre-drilling Secure Mounting Bracket CT-7 and CT-9 to the bumper with provided M6 25mm Bolt, Washer, and Nut NOTE: Reach under the bumper to place the Washer and Nut inside the bumper Secure Mounting Bracket CT-7 and CT-9 to the Main Panel with provided M6 16mm Bolt, Finishing Washer, and Nut Pre-Drill x2 CT-9 Washer x4 M6 25mm Bolt x2 M6 16mm Bolt x2 CT-7 CT-7 CT-8 CT-9 Finishing Washer x4 M6 M6 M6 Finishing 55mm Bolt 25mm Bolt 16mm Bolt Washer Nut x6 Washer Nut CT-8 CT-8 x2 STREET AERO CT-7 CT-9 M6 16mm Bolt x2 M6 55mm Bolt x2 M6 25mm Bolt x2 Behind Mounting Brackets ! IMPORTANT: DO NOT over tighten or use power tools to mount the Mounting Brackets 2 STEP: 4 Attach and secure Mounting Bracket CT-10 and CT-11 to the Side Panel with M6 16mm Bolt, Finishing Washer, and Nut NOTE: Push the bolt all the way into the socket to prevent it from falling out Attach the Side Panel to the Main Panel with Small Bolt and Small Nut NOTE: Do Not tighten Small Bolt (you will need to remove the Side Panel to pre-drill) Mark where Mounting Bracket CT-10 and CT-11 will be mounted to the bumper NOTE: Use the hole on top of CT-10 and CT-11 to mark the drill location Pre-drill into the bumper NOTE: Side Panel and Mounting Bracket may need to be removed before pre-drilling Mount the Side Panel by securing Mounting Bracket CT-10 and CT-11 with M6 25mm Allen Bolt, Finishing Washer, Washer, and Nut NOTE: Reach under or to the side of the bumper to place the Washer and Nut inside the bumper Repeat to install Passenger Side Panel to the Main Panel and bumper CT-10 CT-11 CT-12 CT-13 M6 16mm Bolt x4 M6 25mm Allen Bolt x4 Behind Mounting Brackets Nut x8 Washer x4 CT-10 CT-10 CT-11 CT-12 CT-13 Pre-Drill x4 M6 16mm Bolt x4 CT-11 M6 25mm Allen Bolt x4 Finishing Washer x4 M6 25mm M6 Finishing Allen Bolt 16mm Bolt Washer Washer Nut Small Bolt Small Nut CT-12 CT-13 Main Panel Small Nut x4 Side Panel Small Bolt x4 3! IMPORTANT: DO NOT over tighten or use power tools to mount the Mounting Brackets INSTALLATION GUIDE 2010-2013 Chevrolet Camaro 2SS (Dual Exhaust) Rear Diffuser s-rda-chv-07-e1 www.streetaero.com info@streetaero.com