New Cloud 2.0
Wi-Tek Cloud
Wireless-Tek Technology Limited.
Installation Guide for Wi-Tek models including: WI-AP310 Cloud Managed Outdoor Wireless Access Point, WI-AP310, Cloud Managed Outdoor Wireless Access Point, Wireless Access Point
Внешняя точка доступа Wi-Tek WI-AP310-Lite, PoE, Wi-Fi 4 (802.11N) - Екатеринбург
Внешняя точка доступа Wi-Tek WI-AP310-Lite, PoE, Wi-Fi 4 (802.11N) - Орел
Wireless Router Mode default Login IP: 192.168.11.1 admin/admin. Internet ... Router mode IP: 192.168.11.1. DC. 300Mbps Outdoor AP. Cloud Management http ...
File Info : application/pdf, 1 Pages, 2.45MB
DocumentDocumentInstallation Guide Cloud-Managed Outdoor Wireless Access Point WI-AP310/WI-AP310-Lite/WI-AP316 www.wireless-tek.com Package Content X1 X1 X1 X2 -Installation Guide Cloud Managed Outdoor Wireless Access Point WI-AP310/WI-AP310-Lite/WI-AP316 www.wireless-tek.com X1 Interface and Indicators LED indicator instructions Name PWR LAN/WAN LAN WLAN 300Mbps Outdoor AP Cloud Management http://cloud.wireless-tek.com Fit AP mode IP: 192.168.1.88 Router mode IP: 192.168.11.1 User/Password:admin/adminPoE 24V orDC 12V DC LAN WAN(PoE) Reset Status Bright Flashing Bright Flashing Bright Bright Instruction Outdoor AP be powered up LAN/WAN port date transmit LAN/WAN port connected LAN port date transmit LAN port connected Show Wi-Fi signal strength Ports Instructions DC IN LAN LAN/WAN(PoE) Reset Ports & Buttons DC IN LAN LAN/WAN Reset Ports Instructions 12V 1A DC Input at both Fit AP and Router mode, this port always is LAN At Fit AP mode this port is LAN, at Router mode this port is WAN Reset button, press it for 8seconds for Revert to factory settings Typical Connection Cloud management mode Wi-Tek Cloud Platform: http://cloud.wireless-tek.com AC Gateway mode topology Device installation DC IN LAN(LAN2) LAN(LAN1) Reset Laptop Passive PoE Adapter supports up to 100 meter Power over Ethernet deployment Completed connection, push up to restore the AP back cover Please prepare a long enough network cable to connect the POE adapter and AP. Recommend to use a Category 5 (or above) shielded network cable with a ground wire. Place the AP to the selected position and adjust the AP front panel orientation to be approximately the same as the selected direction Connect the PoE adapter's LAN to Pc, Router or Switch based on the network topology PC Configuration Method Method 1. Connect computer to the wireless signal of AP, the default SSID is "WI-TEK xxxx". Password is 88888888 Method 2. Connect computer to the AP by Ethernet cable. Step 1. On the computer, please set the static IP under the same subnet with AP, 192. 168. 1. xx Step 2. Please launch a browser such as Google Chrome or Firefox, type 192.168.1.88 into address bar and click on enter to get in the login page of wireless access point. The default login password is "admin". *Login device admin Login Step3. After get in the management page,On the left side menu, please go to [Wizard] to setup the access point Step4. Select the appropriate operation mode and follow the instruction of wizard to finish the settings. If already exist a Router in your network, please choose, Fit AP mode; if not, you can choose Wireless Router mode Notice: if you do a reset, AP will recovery to Fit AP mode Fit AP Mode default Login IP: 192.168.1.88 admin/admin Power Internet WAN LAN Router WAN/PoE AP Laptops Phones Wireless Router Mode default Login IP: 192.168.11.1 admin/admin Power Internet WAN/PoE AP Laptops Phones Cloud management settings Step 1 Launch your web browser then enter http://cloud2.wireless-tek.com in the address bar. Step 2 Register an account password by user name or email. Step 3 log in to the cloud account with the account password after registration. After the login is successful, the steps to bind the device on the cloud account are as follows: (1) Click ADD NETWORK (2) Fill in the group name and location, click save. (5) In the relevant device options, you can see the bound device information. Warranty Card 3And click next. 6 Click Tunnel, Select binding device type, click EWEB to log in to the device. (4Enter serial number, click ADD to create and click FINISH,the configuration is complete. Note:The 17-digit SN code of the Add device is shown on the sticker on the back of the device. Username Address Telephone No. Purchase Shop Purchase Address Product Model No. Purchase Time Serial No. Dealer Signature If the product defects within three months after purchase, we will provide you a new product of the same model. If the product defects within the three-year warranty period, we will provide the professional maintenance service. Proof of purchase and a complete product serial number are required to receive any services guaranteed as part of the limited warranty. Any other defects that are not caused by workmanship or product quality, such as natural disaster, water damage, extreme thermal or environmental conditions. sticker damaged, warranty card losing will disqualify the product from limited warranty. Technical Support Cloud Management Company Website Wireless-Tek Technology Limited Address: Room 402 4F, BiaoFan Technology Building, Bao'An Avenue, FuYong Town, Bao'An district, ShenZhen Website:www.wireless-tek.com Tel:86-0755-32811290 Email:sales@wireless-tek.com Technical Support:tech@wireless-tek.com RoHS