User Manual for SmartAVI models including: SWP-T10 Wall Plate Extender, SWP-T10, Wall Plate Extender, Plate Extender, Extender
SWP-T10 - SmartAVI
File Info : application/pdf, 8 Pages, 1.08MB
DocumentDocumentSWP-T10 Wall Plate Extender 1080p Extends VGA, stereo audio, HDMI, IR and RS232 signals with CAT5e/6 up to 70 meters. USER MANUAL (rev 1.0) WHAT'S IN THE BOX PART NO. QTY DESCRIPTION SWP-T10 1 PS12V2A 1 1 HDBaseT Wall Plate Transmitter Power Supply SWP-T10 Quick Start Guide CONNECTING THE HDX-WPRO 1. Install the SWP-T10 transmitter and place the SmartAVI HDX RX receiver unit in close proximity to the output device. 2. Connect a Cat5e/6 cable between the TX and RX units (up to 70m). 3. Connect a signal source to the SWP-T10 via HDMI, VGA, Stereo Audio, RS232 or IR connectors. 4. Connect the HDX RX unit to the desired output device. 5. Connect a 12V power supply to either the SWP-T10 or the HDX RX unit. The other device will be powered via POE (Power over Ethernet). 6. Use the TX front panel SELECT SOURCE button to switch between source signals. Using automatic selection will select the last source connected. Optional: 1. Connect an RS232 cable between SWP-T10 and a personal computer and a RS232 cable from the HDX RX unit to any RS232 device to remotely communicate with or control your RS232 device. 2. To extend IR remote control from the SWP-T10 to the HDX RX unit, connect an IR receiver to the SWP-T10 and an IR Emitter to the HDX RX for infrared remote control up to 20m 2 SWP-T10 © 2016 SmartAVI, Inc. SWP-T10 FRONT SWP-T10 BACK © 2016 SmartAVI, Inc. SWP-T10 3 TECHNICAL SPECIFICATIONS PORTS Input ports 1 x HDMI, Type A 19-pin, female; 1 x VGA HD-15, female; 1 x AUDIO IN(Stereo);1 x IR IN; 1 x RS-232 3p captive screw connector; 1 x 2p captive screw connector Output ports 1 x IR OUT; 1 x RJ45; 1x RS-232 3p captive screw connector; VIDEO Max Data Rate Maximum Pixel Clock Resolutions Compliance with HDMI standard AUDIO Frequency Response Stereo Channel Separation Bandwidth OTHER Power Input Power Consumption Dimensions Weight Operating Temp. Storage Temp. Humidity ESD Protection 6.75Gbps 225MHz Up to 1920x1200 or 1080P@60Hz Supports HDMI 1.4 and HDCP1.2 20Hz ~ 20KHz >75dB@20Hz ~ 20KHz 20Hz ~ 25KHz 12V DC or 24V DC, 2A undetermined 4.6" W x 4.6" D x 1.45" H 0.75lbs 0° to +40°C (32° to 104°F) -20°C ~ 60°C / -4 °F ~ 140 °F 10% ~ 90% Human body model: ±8kV (air-gap discharge) ±4kV (contact discharge) ORDER INFO Part No. Description SWP-T10 HDMI, VGA, Stereo Audio, IR POE Extender with Integrated Scaler and Converter. Includes [SWP-T10-TX, PS12VD2A-WLLMNT] 4 SWP-T10 © 2016 SmartAVI, Inc. METHODS TO CONTROL SWP-T10 Front Panel Button The Select/Auto button selects an input source. If you press and hold the button, the SWP-T10 will enter the automatic switching mode and the AutoSwitch LED lights up. If you press and hold the button again, the SWP-T10 will exit the automatic switching mode. RS-232 External Protocol (PC User) Supports bi-directional RS-232 pass-through control. This protocol is for communication between PC user and board. The following settings should be used: 9600 baud rate, 8 data bits, no parity bits, 1 stop bit, and no flow control. Table 1: Switch to HDMI Switch to VGA Auto ON Auto OFF RES 1 RES 2 RES 3 RES 4 RES 5 SW Update Reset to Default Table 2: Version CHK RES CHK SRC Command Protocol Changes the source to HDMI Changes the source to VGA //HD<CR><LF> //VG<CR><LF> Enable auto-switching by detecting hot plug. //AE<CR><LF> Disable auto-switching by detecting hot plug. //AD<CR><LF> Select Change the resolution to 1920 x 1200. //R1<CR><LF> Select Change the resolution to 1920 x 1080. //R2<CR><LF> Select Change the resolution to 1360 x 768. //R3<CR><LF> Select Change the resolution to 1280 x 720. //R4<CR><LF> Select Change the resolution to 1024 x 768. //R5<CR><LF> Software update for MSTAR chip. //SU<CR><LF> Reset to factory defaults //RD<CR><LF> Query Protocol Checks current version of MSTAR software. //V?<CR><LF> Version Vx.x.x Checks the current resolution. //R?<CR><LF> Resolution: xx Checks the current source. //S?<CR><LF> Input: xx © 2016 SmartAVI, Inc. SWP-T10 5 IR Function Control devices like HDTVs, BluRay players, and more with IR Cable Pin Assignment IR Receiver (RX) IR Emitter (TX) 6 SWP-T10 © 2016 SmartAVI, Inc. Notes: © 2016 SmartAVI, Inc. SWP-T10 7 NOTICE The information contained in this document is subject to change without notice. SmartAVI makes no warranty of any kind with regard to this material, including but not limited to, implied warranties of merchantability and fitness for particular purpose. SmartAVI will not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance or use of this material. No part of this document may be photocopied, reproduced, or translated into another language without prior written consent from SmartAVI Technologies, Inc. Designed and Manufactured in the USA 800.AVI.2131·818.503.6200 Tel: (818) 503-6200 2455 W Cheyenne Ave, Suite 112 North Las Vegas, NV 89032 SmartAVI.com