OLIGHT® Official Store: Tactical Light & EDC Flashlights & Headlamps- Olight
User Manual for OLIGHT models including: PL-Mini 3 Valkyrie Compact Rail Mounted Light With Convenient Magnetic Charging, PL-Mini 3, Valkyrie Compact Rail Mounted Light With Convenient Magnetic Charging, Light With Convenient Magnetic Charging, Convenient Magnetic Charging, Magnetic Charging
20 feb 2024 — Operating instructions as below：. 2.1 Remove the ... the warnings in the manual. WARRANTY. Within 30 days of ... GLOCK is a registered trademark of GLOCK LLC.1 pagina
File Info : application/pdf, 1 Pages, 879.92KB
DocumentDocumentUSER MANUAL PL-Mini 3 Valkyrie A compact rail-mounted light with convenient magnetic charging. IN THE BOX Table 2: MCC PL-Mini 3 Valkyrie Cable length Input Output Time to fully charge MCC Allen Wrench 0.5m USB-A 5V 1A CC&CV 4.2V±0.05V 1A About 55min Figure 3 2 Battery installation Figure 4 Screw off 1 Figure 6 Turn the light on/off GL Adapter 1913 Adapter Screws M3x4 Socket Screws Figure 1 Remove the insulating film before use Table 1 Specifications COOL WHITE CCT: 6500K CRI: 70 HIGH 1min 600 lumens 100% 17% 75min 1 2,500cd 100m IPX6 1m Working temperature 0~40°C (L)52.5*(W)27.6*(H)33.8mm (L)2.07*(W)1.09*(H)1.33in 260mAh 3.7V (0.96Wh) 68g/2.40oz (Including Batteries) * Above data are tested per ANSI/NEMA FL 1-2019 standard in Olight's labs for reference. Push the slider to the left to unlock the battery. Remove the battery upward and remove the insulating film. Figure 2 Charge the battery Green: Charging Completed Red: Charging Insert the battery downward. 2 Press OFF ON Figure 5 Figure 7 Adjust the installation position of the Momentary on rail-mounted light and tighten the screw Push the slider to the right to lock the battery. Press and hold Or Momentary on Figure 8 Turn on/off the strobe function At least 5 times >1 sec Strobe Figure 9 Strobe Double press Or Strobe Figure 10 Battery power indicator Green:60% Orange: 10~60% Red: 10% Press the button once to activate the indicator. How to operate: 1. Product specifications, see Table 1 and Table 2. 2. Operating instructions as below 2.1 Remove the insulating film before use, see Figure 1. Before first use, push the slider to the left to unlock, then remove the battery before removing the insulator. 2.2 Charge the battery, see Figure 2. 2.3 Battery installation, see Figure 3. Put the battery in after aligning its position (slider on the main part shall align with the unlock position). Push the slider to the right to lock the battery. Note: To insert or remove the battery, apply pressure to the battery and slide the slider to lock or unlock the battery in place. 2.4 Screw off, see Figure 4. 2.5 Adjust the installation position of the rail mount light and tighten the screw, see Figure 5; 2.6 Turn the light on/off, see Figure 6; Quickly single press (press and then quickly release) any key, the output will stay lit. press the button again and the output turns off. 2.7 Momentary on, see Figure 7; Press any button and hold, output turns on when pressed and off when released. 2.8 Turn on/off the strobe function, see Figure 8; In the off state, quickly press any button at least 5 times, press and hold (for more than 1 second) on the last press, then turn on or off the Strobe function, and release the button to turn off the power. (Strobe indicates Strobe function is on, constant light indicates Strobe function is off). 2.9 Strobe (when strobe mode is on), see Figure 9. In strobe mode, quickly double-press the button to activate the strobe. The strobe will continue when the button is released. Press any button to turn off the strobe. 2.10 Battery power indicator, see Figure 10. Remove the battery from the main unit, press the button once. The indicator lights up when the button is pressed and goes off automatically after 3 seconds. WARNING ·Keep away from babies and young children. ·Do not store, charge or use the flashlight in a car or similar places where the temperature may exceed 60°C. ·Do not look directly at the light source or shine to eyes, because it may cause temporary blindness or permanent damage to the eyes. ·Do not block the light at close range, the energy emitted from the light may cause the object to burn. ·CAUTION HOT: Do not touch the hot surface place, it may cause skin burns. ·Do not charge the light with any other non-specified chargers. NOTICE ·Do not disassemble the product. ·Do not put a hot light into any type of fabric bag or fusible plastic container. ·Do not activate the maximum brightness mode multiple times continuously to prevent the high temperature on the surface. ·When the light gets hot, please switch it to low brightness mode, or shut off the flashlight temporarily. ·Active thermal protection: The built-in sensor monitors the temperature in real time. After operating for a fixed period of time in high brightness, it prevents overheating by reducing the output. ·Do not immerse the flashlight in seawater or other corrosive media as it will damage the product. ·It is normal that the light flickers when the battery is close to running out. ·For products with magnet-sensitive switches, the brightness and mode may be inconsistent when approaching a strongly magnetic object. This is a normal phenomenon. ·When the battery is at low voltage, the maximum output will be capped at a relatively low brightness. ·The P365 rail mount only fits on P365 rails. The GL adapter is installed as a factory default and suitable for Glock rails. If used with other rails such as MIL-STD-1913 or Hellcat, it needs to be replaced by the user. ·NYLOK is a registered trademark of NYLOK LLC. ·GLOCK is a registered trademark of GLOCK LLC. ·The battery is non replaceable. If damaged, please contact customer service for maintenance. ·Before long term storage, please fully charge the battery. ·Do not short-circuit the charging port with the metallic objects. ·Do not put it in the mouth or lick it, leakage of the charging port can cause discomfort. ·Keep the charging port clean and dry. ·It is recommended to use an USB adapter with a power of 10W (DC5V2A) or above. If the current of the adapter is lower than the max current required for charging the product, the charging time will exceed the nominal time. ·Please mind the battery installation direction. The side with a lock logo should face towards the slider. ·If the battery is in protection mode, the battery indicator may not light up after pressing its button, or the light may fail to illuminate even with the battery installed. In such a case, connect the battery to the magnetic charger to exit protection mode. EXCLUSION CLAUSE Olight is not liable for damages or injuries sustained resulting from the usage of the product inconsistent with the warnings in the manual. WARRANTY Within 30 days of purchase: Contact the original seller for repair or replacement. Within 2 years of purchase: Contact Olight for repair or replacement. USB magnetic charging cable: One year. This warranty does not cover normal wear and tear, modifications, misuse, disintegrations, negligence, accidents, improper maintenance, or repair by anyone other than an authorized retailer or Olight itself. USA Customer Support cs@olightstore.com Global Customer Support contact@olightworld.com Visit www.olightworld.com to see our complete product line of portable illumination tools. Dongguan Olight E-Commerce Technology Co., Ltd. 4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China. Made in China CAN ICES-005( B ) / NMB-005( B ) 3.4000.0610 A. 06, 04, 2023 THANK YOU!