Owner's Manual for DEAF BONCE models including: 60, 80, 60 Machete Fight, 60, Machete Fight, Fight
Machete Fight 60 | Alphard Group
Machete Fight 80 | Alphard Group
FIGHT 60
FIGHT 80
MACHETE SERIES
1. Introduction 2. Safety instructions 3. Wiring diagrams 4. Filtering, recommended amplifier settings 5. Specifications 6. Dimensions 7. Box contents 8. Warranty period, after-sales service and service life information 9. Information on disposal of the electrical and electronic equipment
(for the European countries with separate waste collection)
Thank you for purchasing of this Deaf Bonce product! Our company is committed to the creation of extremely loud sound systems with no loss of quality.
To ensure proper use, please carefully read through this manual before using this product. It is especially important that you read and observe caution's in this manual. Please keep the manual in a safe and accessible place for future reference.
The correct choice of amplifier, its settings, filtering and enclosure largely influence on the lifespan of your audio system. You should select an amplifier with a nominal power, not exceeding the nominal power of the speakers. Proper coordination of the head unit (HU) with the amplifier will allow to get clean, undistorted signal applied to the component to prevent overheating and voice coil damage. Recommended settings of the amplifier and HU: Volume of HU should not exceed 80%. The amplifier sensitivity should be set to 50%.
The recommended filter settings: The high pass filter HPF (the filter that cuts all frequencies below those set for the filter) should be set to 150-250 Hz (24 dB/Oct) or 250-350 Hz (12 dB/Oct) The low pass filter LPF (the filter that cuts all frequencies above those set for the filter) should be set to 8-12 kHz (12 dB/Oct) Recommended amplifiers: MFA-2.80, MFA-2.120, MFA-2.220, MFA-2.320, MFA-2.420, MFA-2.520, MFA-4.80, MFA4.120, MFA-4.180, MFA-4.220, MFA-4.320, MFA-5.1000.
Fight 60 / Fight 80: HPF - 150-250 Hz (24 dB/Oct) LPF - 8-12 kHz (12 dB/Oct)
Fight 60 6.5
Cloth Pressed paper Stamped steel
Ferrite 100 200 1
CAW 90 - 17 000
4 94.9 86 13.88 0.48 5.15
Fight 80 8
Cloth Pressed paper Stamped steel
Ferrite 130 260 1.2
CAW 75 - 15 000
4 96.4 75 26.83 0.43 6.59
71.1 mm / 2.8" 76.88 mm / 3.03"
FIGHT 60 FIGHT 80
Ø161 mm / 6.34" Ø170 mm / 6.69"
Ø198 mm / 7.8" Ø208 mm / 8.19"
Connection of terminals
Ø118 mm / 4.65" Ø149.7 mm / 5.9"
Ø126 mm / 4.96" Ø186.61 mm / 7.35"
81.6 mm / 3.21" 88.4 mm / 3.48"
Installation
7.BOX CONTENTS
Each Deaf Bonce product is warranted to be free from defects in materials and workmanship under normal use and service. The warranty period for the product is 12 (twelve) months from the date on which the product is transferred to the consumer (this date shall be deemed to be the date on which the consumer starts using the product). During the warranty period, defective parts will be repaired or replaced at the discretion of the manufacturer provided that there are grounds for doing so under the laws of the consumer's country. The defective product must be returned to the dealer from whom it was purchased together with the duly filled out warranty certificate, complete, with original packaging. Our company shall not be liable for any damage caused by transportation. Our company shall not be liable for any expenses or lost profits arising out of or in connection with the use or inability to use the product or any other incidental or indirect costs, expenses, or damages incurred by the customer. The warranty is valid in accordance with the laws currently in force. For more information, please visit our company website and refer to the warranty card. The manufacturer reserves the right to change the design and specification of the product without prior notice. The service life of the product is 12 (twelve) months from the date on which the product is transferred to the consumer (this date shall be deemed to be the date on which the consumer starts using the product). The product or any part (component) of the product must not be used in any way (including, but not limited to use for intended or any other purpose, transportation, storage, modification/alteration/improvement/upgrade) after the expiry of the service life. At the end of its service life, the product must be disposed of.
FIGHT 60
Manufacturer: Ningbo Basshead I&E Trading Co., Ltd Made in China
FIGHT 80
1. 2. 3. 4. , 5. 6. 7. 8. , 9.
( , )
, , . , . () , , , . : 80%. 50%.
: HPF (, ) - 150250 (24 /) 250-350 (12 /) LPF (, ) - 8-12 (12 /) : MFA-2.80, MFA-2.120, MFA-2.220, MFA-2.320, MFA-2.420, MFA-2.520, MFA-4.80, MFA-4.120, MFA-4.180, MFA-4.220, MFA-4.320, MFA-5.1000.
Fight 60 / Fight 80: - 150-250 (24 /)
- 8-12 (12 /)
Fight 60
Fight 80
6,5
8
100
130
200
260
1
1,2
90 - 17 000
75 - 15 000
4 94,9 86 13,88 0,48 5,15
4 96,4 75 26,83 0,43 6,59
, , .
71,1 / 2,8" 76,88 / 3,03"
FIGHT 60 FIGHT 80
Ø161 / 6,34" Ø170 / 6,69"
Ø198 / 7,8" Ø208 / 8,19"
Ø118 / 4,65" Ø149,7 / 5,9"
Ø126 / 4,96" Ø186,61 / 7,35"
81,6 / 3,21" 88,4 / 3,48"
7.
8 . ,
Deaf Bonce .
12 () ( , ).
, , , . , , , .
. , , , . . .
.
12 () ( , ).
( , : , , , , , //) , (), .
.
FIGHT 60
: Ningbo Basshead I&E Trading Co., Ltd
FIGHT 80
CorelDRAW 2024 iLovePDF