Energy Saving Light Bulbs, Light Fixtures | CFL, LED & More
Contact Us - Feit Electric
Energy Saving Light Bulbs, Light Fixtures | CFL, LED & More
Installation Guide for FEIT Electric models including: UCL36FP-5CCTCAG3, UCL36FP 5CCTCAG3, Flat Panel Under Cabinet Light, UCL36FP 5CCTCAG3 Flat Panel Under Cabinet Light, Panel Under Cabinet Light, Under Cabinet Light, Cabinet Light, Light
Feit Electric Company UCL36FP5CCTCA FLAT PANEL UNDER CABINET LIGHT SYW-UCL36FP5CCTCA SYWUCL36FP5CCTCA ucl36fp5cctca
File Info : application/pdf, 7 Pages, 745.33KB
DocumentDocumentModel: UCL36FP/5CCTCAG3 FLAT PANEL UNDER CABINET LIGHT FITS 36 IN. CABINETS (32 1/2 IN. TOTAL LENGTH) IMPORTANT SAFETY INSTRUCTIONS AND INSTALLATION GUIDE READ BEFORE INSTALLATION SAVE THESE INSTRUCTIONS Questions, problems, missing parts? Before returning to the store, call Feit Electric Customer Service 8 a.m. - 5 p.m., PST, Monday - Friday 1-866-326-BULB (2852) FEIT.COM We appreciate the trust and confidence you have placed in Feit Electric through the purchase of this Under Cabinet Light. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Feit Electric. Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pre-Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Single LED Fixture Hardwire Installation. . . . . . . . . . . . . . . . 4-5 Alternative Plug-In Installation . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Safety Information Save These Instructions IMPORTANT SAFEGUARDS: CAUTION: Do not attempt to install while plugged in. This ALWAYS FOLLOW BASIC SAFETY PRECAUTIONS WHEN USING ELECTRICAL PRODUCTS, ESPECIALLY WHEN CHILDREN ARE PRESENT. fixture is for indoor use only. Not for use with plastic cabinets. Do not install this fixture inside a totally enclosed cabinet. Do not mount over stoves. RF exposure statement This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. WARNING: To avoid risk of electrical shock, always make sure the product is unplugged from the electrical outlet before This equipment meets the exemption from the routine evaluation limits in section 2.5 of assembling, disassembling, relocating, servicing or cleaning it. RSS-102. It should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Cet équipement est conforme à l'exemption des limites d'évaluation habituelle de la section 2.5 de la norme RSS-102. Il doit être installé et utilisé à une distance minimale de 20 cm CAUTION: Do not install this product in a wet location. entre le radiateur et toute partie de votre corps. IC WARNING This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: CAUTION: Do not install this product in an outdoor location. (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux CAUTION: Do not use chemical solvents or harsh abrasives to clean the fixture. appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. L'appareil ne doit pas produire de brouillage; 2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Supplier's Declaration of Conformity: 47 CFR § 2.1077 Compliance Information Responsible Party: Feit Electric Company 4901 Gregg Road, Pico Rivera, CA 90660, USA 562-463-2852 Unique Identifier: UCL36FP/5CCTCAG3 FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Limited Warranty This product is warrantied to be free from defects in workmanship and materials for up to 5 years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com/contact-us or call 1-866-326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province. 2 WWW.FEIT.COM Please contact 1-866-326-BULB (2852) for further assistance. Pre-Assembly TOOLS REQUIRED PHILLIPS FLAT HEAD PENCIL PLIERS 18 AWG SCREWDRIVER SCREWDRIVER WRENCH WIRE STRIPPER HARDWARE INCLUDED NOTE: Hardware not shown to actual size. AA BB CC DD EE FF GG HH II Part Description AA 36 in. LED Flat Panel Fixture BB 18 in. Linking Cable CC Mounting Screws DD Fixture Mounting Template EE Hardwire Bracket FF Hardwire Bracket Screw GG Wire Nut HH Clamp Connector II Mounting Brackets Quantity 1 1 4 1 3 1 3 1 2 Item No. UCL36FP/5CCTCAG3 Description 36 Inch Flat Panel Under Cabinet LED Fixture Maximum Linkable Wattage Input Maximum Linkable Units with Volts (V) Per Fixture (W) Current (mA) Units at 120V In-Wall Dimmer 120 28 240 24 5 Distance LIGHTING DISTRIBUTION Center Beam (Foot Candles) Beam Diameter 3 ft 96 5 ft 34 8 ft 13.5 15 ft 3.8 7.2 ft 12 ft 19 ft 36 ft Beam Spread: 100° CD @ CB: 861 3 WWW.FEIT.COM Please contact 1-866-326-BULB (2852) for further assistance. Single LED Fixture Hardwire Installation 1 Turn Off the Power Turn the power OFF from the breaker panel before starting installation. 5 Removing the Knock-out Carefully remove the knock-out with a flathead screwdriver. OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF 2 Position the Fixture Find the desired place for the LED light fixture and mark clearly using the provided mounting bracket template (DD). DD EE 6 Installing the Clamp Connector to the Knockout Hole Install the Clamp Connector (HH) to the knock-out hole by inserting it through the hole and securing it with the nut. The Clamp Connector (HH) should be on the outer side of the bracket. 3 Installing the Mounting Brackets Screw in the Mounting Brackets (II) on the marked locations. II Marked locations Mounting screws 4 Removing the Hardwire Bracket Remove the screw on the hardwire bracket, then slide and lift the bracket off of the fixture. x 3 1 2 x HH EE 7 Cutting and Stripping Wires Take out of the black and white 18 AWG wires in the fixture. Cut and strip the wires to the correct length. 4 WWW.FEIT.COM Please contact 1-866-326-BULB (2852) for further assistance. Single LED Fixture Hardwire Installation (continued) 8 Wire Power Supply to the Fixture Feed the supply wire through the Clamp Connector (HH) and knockout hole and make all connections using the wire nuts provided. Connect the 120V line (black) wire to the black wire. Connect the neutral (white) wire to the white wire. Connect the ground (green) wire to the green wire. 10 Secure Supply Wires with the Clamp Connector Secure the supply wire by firmly screwing the clamp connectors down on the wire. Fig. 1 Black White x Green x HH 9 Replace the Wiring Bracket After connecting the wires correctly, place the wires inside the fixture and reinsert the bracket, sliding it over and screwing it secure. 11 Installing LED Fixture Lift the light fixture (AA) up to the C-channel brackets (II). Push firmly until the C-channel brackets (II) snap into the light fixture (AA). x 1 3 II 2 x AA EE X HH X 12 Linking LED Fixtures Connect the LED Fixtures (AA) using the provided Linking Cable (BB). AA BB NOTE: To install 2 or more LED fixtures, repeat the single fixture installation instructions with two or more units. 5 WWW.FEIT.COM Please contact 1-866-326-BULB (2852) for further assistance. Alternative Plug-In Installation (Electrical Plug not Included) 1 Position the Fixtures Find the desired place for the LED light fixture and mark clearly using the provided mounting bracket template (DD). 4 Connecting the Power Supply Plug In Electrical Plug to the LED Fixture (AA). DD 2 Installing the Mounting Brackets Screw in the Mounting Brackets (II) on the marked locations. AA Electrical Plug NOTE: The electrical plug can be connected to either side of the LED Fixture (AA). II Marked locations Mounting screws 5 Connecting to a Power Outlet Connect the Electrical Plug to the power outlet on the wall. 3 Installing LED Fixture Lift the light fixture (AA) up to the C-channel brackets (II). Push firmly until the C-channel brackets (II) snap into the light fixture (AA). II AA 6 WWW.FEIT.COM Please contact 1-866-326-BULB (2852) for further assistance. Operating Instructions ON/OFF and DIM Button CCT Button Use the ON/OFF and Dim Button for ON/OFF Operation and to Change the Dimming Levels To select the desired dimming level, cycle through the dimming levels (High, Medium, Low, Dim, Off) by pressing the Dim Button. This setting will be fixed each time the ON/OFF switch is turned ON. Changing the Color Temperature Setting To select the desired color temperature, cycle through 2700K - 3000K - 3500K - 4000K - 5000K by pressing the CCT Button. This setting will be fixed each time the ON/OFF switch is turned ON. This LED Fixture has the feature to operate and control multiple units, even if they are not linked. To control multiple fixtures, Hold the CCT button for 3 seconds on all the fixtures to be controlled in a group. To remove the individual fixture from the group, Hold the CCT button on the fixture that you want to control individually for 3 seconds. 7 WWW.FEIT.COM Please contact 1-866-326-BULB (2852) for further assistance.