Breezary Ceiling Fan - Online Ceiling Fan Store
Installation Guide for Breezary models including: 24020-BK, 645567713323, 24020-BK 19 Inch Black LED Indoor Downrod Ceiling Fan, 19 Inch Black LED Indoor Downrod Ceiling Fan, Black LED Indoor Downrod Ceiling Fan, LED Indoor Downrod Ceiling Fan, Indoor Downrod Ceiling Fan, Downrod Ceiling Fan, Ceiling Fan, Fan
19-in Black LED Indoor Downrod Ceiling Fan with Light Remote (5-Blade) 645567713323
File Info : application/pdf, 13 Pages, 10.97MB
DocumentDocument19 Customer Service: support@ breezary.com Table of Contents Table of Contents..................................................2 Safety Information.................................................2 Dimension Reference............................................3 Hardware Included................................................3 Fan Parts Included................................................3 Exploded View......................................................4 Installation Instructions.........................................5 Troubleshooting Guide........................................12 Safety Information READ AND SAVE THESE INSTRUCTIONS. 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin. 2. All wiring must be in accordancce with the National Electrical Code "ANSI/NFPA 70" and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs (15.9 kg). Use only UL Listed outlet boxes marked " Acceptable for Fan Support of 35 lbs. (15.9 kg) or less. " 4. Do not place objects in the path of the blades. 5. To clean the fixture,turn off the power, wait for it to cool, and wipe the fixture with a clean, soft cloth. 6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipmentgrounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box. 7. All setscrews must be checked and retightened where necessary before installation. WARNING: To reduce the risk of electrical shock or fire, not use this fan with any solid-state fan speed control device. It will permanently damage the electronic circuitry. WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing the rackets balancing the blades, or cleaning the fan. Do not insert WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked "acceptable for fan support of 35 lbs. (15.9 Kg) or less" and use screws provided with the outlet box. WARNING: To avoid possible electrical shock, turn the electricity off at the main fuse box before wiring. WARNING: To reduce the risk of electrical shock, this must be installed with an isolating wall control / switch. CAUTION: To reduce the risk of personal injury, use only the screws provided with the outlet box. CAUTION: The fan must be mounted with a minimum of 7 ft (2.1 m) clearance from the trailing edge of the blades to the floor. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2 Expansion Screw 2 2 2 2 3 4 4 4 Canopy Yoke Batteries Yoke cFig.1a Take out the lower post, top cover, yoke cover cFig.1c cFig.1b cFig.1d ecure downrod in position by tightening jam screws. lide yoke cover down and it will flush with the motor housingc Fig.1e 1 The main assembly of the ceiling fan is completed, place it on the cardboard box. If it is installed on the cement top and don't have outlet box, please use two expansion screw. - Use an impact drill to drill two 8mm holes, Note that the distance between the two holes is about 100mm. - Completely insert the pipe part of the screw into the hole and remove the washer and nut. - Place the hanger into the screw head, place the washer, and then use a wrench to tighten the nut. Cement roof Expansion Screw JO Washer Nut Mounting Bracket ake the following wire connections to the receiver unit see fig 6 using the wire nuts supplied SUPPLY CIRCUIT 120V 6 B. Push all connected wires up into ceiling box. - Put the receiver into the mounting bracket as shown in figure 7. - When installing the canopy, ensure the antenna is not pressed by the canopy. - Ensure to connect all ground wires accordingly. Fig. 7 Mounting Bracket Receiver Canopy C.FUNCTION INSTRUCTION OF EMITTER Learning code and matching mode is used between emitter and receiver. - Open battery cover on the hand-held remote and install battery, pair of AAA of emitter (1.5V) that are not included. - If the emitter can not control the fan, learning code matching mode is used between emitter and receiver. Turn "ON" the supply power within 10 seconds and press the emitter's " " button for 5 seconds, it can load normally after hearing a long sound "bee", which means learning successfully and it can works normally. - When the emitter cannot control the receiver,please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power. - When the emitter cannot control the receiver, please check is there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled product with the same frequency will disturb each other. - Please take out the battery from the emitter when leaving unused for long time. - When installing the fan, the fan ceiling cover don't press the antenna(or other wire),it is easy to breakdown the wire and short-circuited. Light Switch Speed Controller Fan Shutdown Timer Indicator Light - Place two screws and washers on mounting plate which correspond with slots in canopy. Screw in two turns. - Carefully rotate fan assembly until groove in hemisphere locks over tab of canopy assembly. - Loosen (do not remove) the two screws on mounting bracket. Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. - Align the holes on the canopy with mounting bracket and secure with the two set of screws until snug. Hemisphere Groove Mounting Bracket Tab Fig.8a Hemisphere Downrod Fig.8b Groove Canopy Screws By using forward and reverse switches, the fan rotates forward in summer and reverse in winter Forward and backward switch