User Guide for BirdBike models including: A-FRAME Commuter Bike, A-FRAME, Commuter Bike, Bike
yeep.me DAY PLUS – download.yeep.me
Index of /wp-content/uploads/2024/05
SCAN SCAN Remove the black fork protector from the bottom of the fork and discard. Insert the front wheel axle inside of the fork slots. Ensure the brake rotor is
Quick Start Guide SCAN SCAN BirdBike Assembly Video Scan to watch our easy-to-install video Need help? We're here for you. Please reach out to us directly with any questions, concerns or if you need help assembling the Bird Bike. Please do not contact the retailer. A-FRAME 3 Remove the Dash Display Removing the screw from under LED display Gently pull the LED display out from its enclosure within the handlebar. Be careful not to damage any cables. Tool required Tip: If the LED display doesn't pull out easily from the handlebar enclosure, use the 2.5mm Allen key to gently push it out through the screw hole from the back of the handlebar. 2.5mm Allen key Remove the screw from under the LED display using the 2.5mm Allen key. Set aside the screw for use during installation in step 11. Retrieve 2.5mm Allen screw Email bird@ciboxcorp.com 4 Install the Handlebars Aligning the front fork (before mounting the handlebars) Align the fork with the frame so that it is facing forward, the front brake assembly should be on the same side as the kickstand. (rider's left side) Make sure the cables are clear and do not restrict the range of motion needed for steering. 1 Preparation for Assembly Unpack all components from the product package including the Toolkit · Expect ~30 minute assembly time 30 min · Clear a work space · Don't over tighten screws Tools: Y-wrench (3mm / 4mm / 5mm) Parts: L-key Phillips Screwdriver 2.5mm Allen key Wrench (13mm / 15mm) Cap nut and washer (x2) Pedals (x2) Left & Right Wheel Reflectors Rear and Front and fasteners (x2) Reflectors 2 Prep the Handlebar Stem Remove the hex bolt, cap, and cardboard tube from handlebar stem Remove the hex bolt screw from the cardboard tube on the handlebar stem. Set aside the hex bolt for use during installation in step 5. Discard both the cardboard tube and the black cap held in by the hex bolt. Tool required Y-wrench 5mm Set aside Hex bolt Battery Keys Power Supply and Cable Front Fender This QSG & User Manual 5 Attach the Handlebars Attaching the handlebar to the handlebar stem on top of the fork Place the handlebar over the handlebar stem and insert the hex bolt (from step 2) through the handlebar. Tool required Using the 5mm end of the Y-wrench, gently tighten the hex bolt so that there's no play between the fork and frame. Y-wrench 5mm Retrieve 6 Secure the Handlebars Securing the handlebars Tighten the two steering stem screws under the handlebars using the 5mm end of the Y-wrench, so they are securely in place. Tool required Target torque 12±0.5 N m Y-wrench 5mm Hex bolt Target torque 5±0.5 N m 7 Install the Front Wheel Attach the front wheel to the fork Remove the black fork protector from the bottom of the fork and discard. Insert the front wheel axle inside of the fork slots. Ensure the brake rotor is aligned to fit inside the front disc brake. Install washers (serrated side in) and cap nuts onto the outsides of the fork. Tighten them using the 15mm wrench until secure. The correct tire pressure is 50-80 psi. Tool required Wrench 15mm Parts required Target torque 20-25 N m Cap nut and washer x2 11 Reinstall the LED Display Reinstall the display Place the display back into the handlebar enclosure. Be careful not to pinch the cables. Tool required Use the 2.5mm Allen key, reinstall the screw previously removed in step 3 from under the display, so that the display fits flush inside of the handlebar enclosure. 2.5mm Allen key Connect the end of the power cable coming from the bottom of the display to the power cable coming out of the bottom of the frame. Carefully align the arrows on the cables. Retrieve 2.5mm Allen screw 8 Attach the Front Fender Attach the front fender to the fork With the 4mm end of the Y-wrench, remove the two screws attached to the back of the fork. Tool required Re-insert the two screws through the holes at the end of the fender-support bracket to secure them on to the fork. Y-wrench 4mm Use the 4mm end of the Y-wrench to remove the screw that's on the top of the backside of the fork. Re-insert the screw through the fender mount bracket on top of the fender and secure tightly to the back of the fork. Tip: Make sure fender is parallel to the wheel so it doesn't make contact as the wheel rotates. Target torque 5-6 N m 12 Charge Battery Target torque 5-6 N m Connect the charger Use the included power supply and connect it to the charging port on the battery (below the +/- rubber flap). Finish Charging When fully charged, a green light on the power supply indicates the charge is complete. Battery can be charged on the Bike or removed for charging. Please allow 4-6 hours to fully charge your bike. Tip: Use keys to unlock and charge battery. 9 Install the Seat And adjust the seat height Remove the soft rubber cap located on the frame just below the seat column to reveal the seat clamp screw. Tool required Use the 5mm end of the Y-wrench to loosen the seat clamp screw. Adjust the seat post to the preferred height. Once positioned, tighten the seat clamp screw until secure and return the rubber cap in to the frame. Y-wrench 5mm Do not extend the seat post farther than the minimum insertion line indicated on the seat post. Target torque 12±0.5 N m 13 Install Reflectors Rear reflector - red Wrap the bracket for the rear reflector around the seat post. Secure with a flathead screwdriver. Position the reflector facing rearward. Front reflector - white Wrap the bracket for the front reflector around the handlebar near the stem. Secure with a flathead screwdriver. Position the reflector facing forward. Wheel reflectors Wrap the bracket for the wheel reflector around any wheel spoke. Secure with a flathead screwdriver. Tool required Flathead screwdriver (not provided) 10 Install the Pedals Attach the pedals Screw the left pedal marked "L" counter-clockwise by hand (since it is reverse threaded). Screw the right pedal marked "R" clockwise. Tighten both pedals with the 15mm wrench. Each pedal is marked with an "L" or "R" corresponding to appropriate side (left or right) on the bolt end and on the inside of the pedal. See below illustration. L R Tool required Wrench 15mm R L Target torque 30-35 N m Max torque 1,5 N mAdobe PDF library 17.00 Adobe Illustrator 28.5 (Windows)