Installation Guide for Otter models including: UnlinitEd Series Case
UNLIMITED SERIES INSTALLATION. PENCIL HOLDER INSTALLATION: 1 Pencil holder is optional 2 Remove rubber plug on right side. of case 3 Insert the pencil holder through. inside of case 4 Then...
Kickstand can be rotated to achieve four ... After installing the pencil holder, ... Remove the protective film on the adhesive side first.
UNLIMITED SERIES INSTALLATION PENCIL HOLDER INSTALLATION: 1 Pencil holder is optional 2 Remove rubber plug on right side of case 3 Insert the pencil holder through inside of case 4 Then pull elastic strap through to outside of case CASE INSTALLATION: 1 After installing the pencil holder, insert tablet into the bottom edge of the case first 2 Push/pinch tablet into case, working around the case perimeter in a circle SCREEN PROTECTOR INSTALLATION: 1 Once tablet is installed into the case, clean the screen thoroughly 2 Remove the protective film on the adhesive side first 3 Using home button and edges of case to align protector, install the screen protector onto the tablet working from the bottom edge towards the top 4 Remove the protective film by pulling on tab KEYBOARD INSTALLATION: KICKSTAND INSTRUCTIONS: 1 Once tablet is inserted into 1 To open kickstand, pinch gray latch A the case button and lift outer ring 2 Make sure keyboard is charged 3 Turn keyboard power switch on 2 Kickstand can be rotated to achieve four different orientations: 4 Press "Fn+C" to turn on wireless matching A. This orientation is recommended for typing and pressing on the tablet B 5 Open Wireless Networks on screen. your tablet and click the keyboard name 6 Input numbers on tablet and B. This orientation is recommended for viewing only. press "Enter" C. This orientation is recommended for ACTIVATING KEYBOARD viewing only. TRACK PAD: D. This orientation is recommended for 1 In tablet setting go to "Accessi- typing and pressing on the tablet C bility", then "Touch" screen. 2 Make sure the Assistive Touch is "on" 3 Snap outer ring back into place 3 Press "Fn+command" to activate D the trackpad *Keyboard automatically sleeps if you do not use it within 10 minutes. To restart, press any key and wait 3-5 seconds. UNLIMITED SERIES INSTALLATION HAND STRAP INSTALLATION: 1 Pinch gray latch to open Kickstand before installing Hand Strap 2 Insert Hand Strap ends through slots at side of the kickstand 3 Fasten Velcro ends of strap together 4 Snap outer ring of kickstand back into place 5 Rotate Hand Strap for comfortable positioning SHOULDER STRAP INSTALLATION: 1 Thread buckle cord through case anchor point 2 Pull cord loop through buckle hook 3 Repeat for other buckle 4 To adjust the shoulder strap, slide one or both of the length adjustment sliders FOLIO INSTRUCTIONS: A 1 The folio can be rotated to be used as a stand in landscape or portrait mode: B A. Rest bottom of tablet in the interior folio groove B. Fold folio into a triangle to prop up the back of the tablet *Folio can be configured into an acute triangle or an equilateral triangle depending on the angle you prefer TABLE STAND INSTRUCTIONS: 1 Remove Allen wrench from underneath the stand base 2 Set stand on flat surface and lift long arm open 3 Release tablet holder arms 4 Insert tablet into holder either horizontally or vertically 5 Click holder hinges firm on tablet A. The holder spins 360°, so you orient tablet into portrait or landscape mode 6 Using the Allen wrench, adjust then tighten the angle of tablet holder hinge, and stand hinge *Stand and tablet holder feature cable holes to thread wires through To attach a tablet with case and kick stand, the holders of the stand should be attached towards one end of the tablet PRIVACY SCREEN INSTRUCTIONS: 1 Privacy Screen Protector can be installed over bare device screen or a screen protector 2 Set Unlimited Series case on a flat surface A. There is no need to remove your tablet from inside the case 3 Using the home button and bottom edge of case for alignment, attach Privacy Screen on top of screen or screen protector 4 To remove Privacy Screen, pull from the upper right corner *Privacy screen adhesive can be cleaned with water and a lint-free cloth *When not in use, store Privacy Screen on included backer boardAdobe PDF Library 15.0 Adobe InDesign 15.1 (Macintosh)