Important Notice and Maintenance
Some tree sap and resins are corrosive. Thoroughly wash the guide bar and sprocket areas after each use, then coat metal parts with light oil.
- Perform all periodic lubrication and services that are required.
- Tighten all the screws and nuts.
- Drain fuel tank completely. Press purge bulb 6–7 times to remove remaining fuel from carburetor then drain the tank again. Close choke, start and run the engine until it stops due to lack of fuel.
- Allow engine to cool. Remove the spark plug lead from the spark plug. Remove the spark plug. Pour 7 cc (0.25 oz.) of fresh, clean, two-stroke engine oil into the cylinder through the spark plug hole.
- Pull the recoil starter handle 2-3 times to distribute the oil inside the engine.
- Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston reaches the top of its travel and leave it there.
- Install the spark plug. Connect the spark plug lead to the spark plug.
Specifications
| Model | PPT-2620 | PPT-2620H |
|---|---|---|
| Length (standard) | 2,716 mm (107 in.) | |
| Length (Extended) | 3,704 mm (146 in) | |
| Width | 273 mm (11 in.) | |
| Height | 260 mm (10 in.) | |
| Weight (dry) | 7.9 kg (17.4 lb.) | 7.7 kg (17 lb.) |
| Engine Type | Air cooled, two-stroke, single cylinder gasoline engine | |
| Bore | 34 mm (1.34 in.) | |
| Stroke | 28 mm (1.1 in.) | |
| Displacement | 25.4 cc (1.55 cu. in.) | |
| Exhaust | Spark arrestor muffler or spark arrestor muffler with catalyst | |
| Carburetor | Diaphragm w/purge pump | |
| Ignition System | Flywheel magneto, capacitor discharge ignition type | |
| Spark Plug | NGK CMR 7H (Gap 0.65 mm [0.026 in.]) | |
| Fuel | Mixed (Gasoline and Two-stroke Oil) | |
| Fuel/Oil Ratio | 50:1 | |
| Gasoline | Use 89 Octane unleaded. Do not use fuel containing methyl alcohol, more than 10% ethyl alcohol or 15% MTBE. Do not use alternative fuels such as E15 or E85. | |
| Oil | ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345- FD, two-stroke, air-cooled engine oil. | |
| Fuel Tank Capacity | 0.53 L (17.9 US fl. oz.) | |
| Starter System | Automatic Rewind Starter | |
| Clutch | Centrifugal Type | |
| Drive Shaft | Aluminum Extrusion | |
| Sprocket Type | 6 tooth spur, 9.53 mm (3/8 inch) pitch | |
| Gear Case Ratio | 1.5:1 | |
| Oiling System | Automatic | |
| Chain Oil Capacity | .2 L (6.76 oz.) | |
| Handles | Right hand grip w/throttle trigger and throttle trigger lockout | |
| Shoulder Harness | Standard | |
| Idle Speed | 3,100 | |
| Clutch Engagement Speed | 4,100 | |
| Wide Open Throttle Speed (W.O.T.) | 11,250 | |
| Guide Bar and Saw Chain (91) | 305 mm (12 in.); 9.53 mm (3/8 inch) pitch chain, 0.050 gauge | |
Product Registration
Thank you for choosing ECHO Power Equipment.
Please go to https://www.echo-usa.com/Warranty/Register-Your-ECHO to register your new product on-line. It's FAST and EASY! NOTE: your information will never be sold or misused by ECHO, Inc. Registering your purchase enables ECHO to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration.
If you do not have access to the Internet, you can complete the form below and mail to:
ECHO Inc., Product Registration, PO Box 1139, Lake Zurich IL 60047.
