Daktronics RTN-3020 Series Panel Installation Quick Guide

C-Clip Mounting Style

Clip Attachment

1. Level the C-clips according to the contract-specific Shop Drawing and their relation to the other clips. Refer to Figure 1.
2. Place a seismic screw in one of the bottom two holes. The upper hole provides the clip with symmetry but is not used for attachment. Tighten the screw through the C-clip. Refer to Figure 2.
3. Once the clips are level and secure, slide the display onto the clips through the gap in the chassis. Refer to Figure 5.
4. Refer to the contract-specific Shop Drawing to determine the Z-axis depth. Measure from the front flange of the chassis to the front flange of each C-clip. Refer to Figure 6.
5. Examine the lower end of the C-clip that is cradling the bottom of the panel. If necessary, place shim tape in the gap between the C-clip and the display. Refer to Figure 7.
6. Screw through the bottom of the C-clip into the display for attachment.
7. Repeat Steps 2-5 for each display section.
8. Remove the display modules from the end sections to access the interconnect location.
9. Once the cabinets have been placed, secure the horizontal interconnect points by inserting one M12 bolt from the right side of the cabinet to the left side of the cabinet. Refer to Figure 8.

Z-Clip Mounting Style

Clip Attachment

1. Ensure the upper wall clips are plumb and level according to the contract-specific Shop Drawing. Refer to Figure 9.
2. Verify the lower Z-clips are installed per the contract-specific Shop Drawing. Refer to Figure 9.

Standard Section Attachment

1. Lift the display sections from the shipping crate using only the supplied lift eyes. A spreader beam is recommended when lifting but is required when ProRail® steel is attached. Refer to Figure 3, Figure 4 and the RTN-3020 Series Section Crate Handling Quick Guide (DD5638339) for details.

Note: Do not set sections on the ground.

Standard Section Installation (Continued)

1. Lift the display sections from the shipping crate using only the supplied lift eyes. A spreader beam is recommended when lifting but is required when ProRail® steel is attached. Refer to Figure 3, Figure 4, and the RTN-3020 Series Section Crate Handling Quick Guide (DD5638339) for details. Refer to Figure 4.
2. Note: Do not set sections on the ground.
3. Use the rear section clips to mount the display section directly to a non-combustible wall surface. Refer to Figure 12 and Figure 13. Ensure the section sits completely in the upper wall clips.
4. Note: Clip placement varies by contract and may differ from what is shown in Figure 12.
5. Ensure the section is plumb, level, and parallel to the wall. The alignment of the first section determines the alignment of the entire display. Refer to Figure 14.
6. Note: Remove the lift eyes from the top perimeter before closing the beverage shroud.
7. Repeat Steps 1-5 to hang the next section. Ensure the sections are flush to the adjoining section in all planes. Follow the steps in Wing Section Installation (p.2) to install a wing section.
8. Install two stitch bolts (#HC-3829060) through the right perimeter into the adjacent cabinet. Remove the modules or the module pan entirely to access the stitch locations. Refer to Figure 15.
9. Note: Section-to-section seam tolerance should be ±5% of the pixel pitch. Pixel pitch = 15 mm, Seam tolerance = ±.75 mm (.030")
10. Attach the display to the lower Z-clips for uplift protection. The modules may need to be removed from the front to attach the display.
11. Note: This varies from contract to contract. Refer to the contract-specific Shop Drawing for further instructions.
12. Close the beverage shroud and use the beverage shroud latches to secure the shroud.

Wing Section Installation (Continued)

1. Attach the top offset pivot bracket to the wing section with supplied TEK screws (#HC-1530). Refer to Figure 18 and Figure 19.
2. Bring the wing section next to the main cabinet sections. Install a screw (#HC-1186) up through the bottom pivot bracket into the bottom perimeter of the wing section. Refer to Figure 20.
3. Align the top of the wing section with the main section and install a screw (#HC-1186) through the top pivot bracket into the offset pivot bracket. Refer to Figure 20. The wing section is now free to rotate. If the wing section does not rotate, ensure the side section stitch bolts to the left of the wing section are removed.
4. Place the top wing bracket on top of the assembled wing connection and secure into the main cabinet. Refer to Figure 21.
5. Set the wing at the necessary angle to engage the left and right sections. Refer to Figure 22. The hinge adds a gap (seam) between the module columns, which is necessary for top-access module removal via the module pan sliders.
6. Once the desired angle is achieved, use the provided jig to mark pilot hole locations for installing top and bottom TEK screws to lock the angle in place. Place the jig over the screw and align the jig to the section's face and perimeter. Pilot holes should be drilled to 0.141" diameter or smaller. Refer to Figure 23 and Figure 24.
7. Install TEK screws (#HC-1530) through the upper and lower wing brackets into the vertical perimeter of the wing to keep the wing from rotating. Refer to Figure 25 and Figure 26.
8. Loosen and remove the upper hinge after all TEK screws are tightened down. The hinge needs to be removed to allow the beverage shrouds to close completely. Refer to Figure 27 and Figure 28.
9. Close and secure the beverage shrouds.