User Manual
Model No. CV-E86 / CV-E87
Product Introduction
Thank you for choosing our company's toy products. Please read these instructions carefully before use for a better operating experience.
Note: The remote-controlled car products shown in this manual are for reference only. Please refer to the actual product for appearance.
This product is assembled and charged by adults and then played with by children. Please use this product under adult supervision.
Warning: Please do not disassemble or modify this product without authorization. Unauthorized changes may render the product unusable.
This manual applies to a series of products from our company. Product configurations may vary. Please refer to the configuration details on the packaging box for specifics.
Product Configuration
Model No. CV-E86
- Screwdriver x1
- Charging cable x1
- Instruction manual x1
- Product vehicle body x1
- Roadblock x4
- 2.4G full-scale pistol-shaped remote control x1
Model No. CV-E87
- Screwdriver x1
- Charging cable x1
- Instruction manual x1
- Product vehicle body x1
- Roadblock x4
- 2.4G full-scale pistol-shaped remote control x1
2.4G Automatic Frequency Pairing Instructions
- After installing batteries in the remote control, turn on the switch. The remote control's indicator light will flash. Turn on the remote-controlled car's switch to initiate the connection. The remote control's indicator light will turn off upon successful connection. If the connection fails, repeat the steps.
- Each remote control can connect to only one remote-controlled car. Once connected, cars will not interfere with each other. Multiple cars cannot be connected simultaneously.
- If the remote control does not detect the 2.4G signal from the powered-on car within one minute, the power indicator light will flash. Restart the remote control's power switch to re-pair the frequency.
- To pair with another remote control or car of the same model, turn off the remote-controlled car's power before re-pairing.
Introduction to Remote Control Functions
Features: 1:64 Simulation scale, 2.4GHz, Drift stunt, Two-speed Switching, Full-scale control, Type-C direct charging, Four-wheel drive, Cool light effects.
Basic Control:
- Forward/Backward: Pull the trigger of the pistol-shaped remote control to move the car forward. Push the trigger backward to move the car backward.
- Steering Control: The rotation angle of the steering wheel on the remote control synchronizes with the front wheel steering angle, allowing for precise directional adjustments. Turn the steering wheel left while pulling the trigger to make a left turn. Turn the steering wheel right while pulling the trigger to make a right turn.
Operation Instructions
Throttle Control
The force applied to the trigger is proportional to the vehicle's speed, enabling stepless speed variation from 0-100%.
Two-Speed Switching
The remote-controlled car defaults to low-speed mode when powered on. Short-press the speed switch button on the remote control to toggle between high and low speeds.
Full-Proportional Control
This remote-controlled car utilizes a high-precision full-proportional control system, supporting stepless speed adjustment across the 0-100% range.
Trim Function
If the remote-controlled car deviates left while driving straight, adjust the trim dial on the bottom of the car to the right until it moves straight. If it deviates right, adjust the trim dial to the left.
Drift Stunts
- Spin Drift: In high-speed mode, turn the steering wheel fully to the side while pulling the trigger all the way down. The car will perform a spin drift.
- Spiral Drift: In high-speed mode, turn the steering wheel fully to one side while pulling the trigger all the way down. Release the steering wheel, and the car will spiral due to inertia.
- Drift Cornering: In high-speed mode, pull the trigger fully, then release it. Immediately turn the steering wheel fully to the side and pull the trigger again. The car will drift around the corner.
- Reverse Drift: In high-speed mode, turn the steering wheel fully to the side while pushing the trigger all the way backward. The car will perform a reverse drift.
Tip: Drifting performs best on smooth, clean, and flat surfaces.
Battery Information
- The product vehicle body uses 1 built-in rechargeable battery.
- The remote control uses 2 non-rechargeable 1.5V AA batteries.
- Install and remove remote control batteries according to the polarity and voltage indicated in the battery compartment.
- Non-rechargeable batteries must not be charged.
- Rechargeable batteries must be charged under adult supervision.
- Do not mix battery types or use a mix of new and old batteries.
- Only use batteries identical or equivalent to the recommended ones.
- Do not short-circuit the power terminals.
How to Charge
- The new battery pack must be charged before use.
- Turn off the power switch of the remote control car. Insert the Type-C plug of the charging cable into the charging port at the bottom of the car. Connect the USB plug to a power source to begin charging. (A standard Type-C data cable can also be used.)
- Charging takes approximately 40 minutes for a full charge. The charging cable has an indicator light: it is red during charging and turns off when fully charged. Do not overcharge.
Operation Tips
- Ensure the power switch is in the "ON" position. The car will not operate if the switch is "OFF".
- When battery power is low, steering may become less responsive, and movement will slow down. Remove the battery for charging.
- The effective control range is approximately 30 meters. Exceeding this range may cause the car to stop or become uncontrollable.
- The car has an over-discharge protection function: if stationary for 3-4 minutes, it will power off. Restart the car and re-pair the frequency. The remote control enters sleep mode after 3-4 minutes of inactivity (indicator light turns off) and can be awakened by any operation.
Maintenance and Care
- This product contains plastic, metal parts, and electronic components. Do not immerse it in water or use it in humid environments for extended periods.
- Regularly inspect wires, plugs, casing, and other components for damage or defects. Stop using the product immediately if damage is found and seek repair.
- Gently wipe the remote-controlled car with a damp cloth if it gets dirty.
- When not in use, remove batteries from the car and remote control to prolong battery life. Store them in the original packaging to prevent damage.
- Keep the product away from fire sources, direct sunlight, high temperatures, and humidity to prevent circuit shorts or fires.
General Fault Handling
| Fault Symptoms | Causes | Solutions |
|---|---|---|
| Vehicle Fails to Move | 1. Remote control not connected or car's switch is off. 2. Batteries improperly installed in the remote control. 3. Insufficient power in the car's rechargeable battery pack. |
1. Turn on the car's switch and reconnect the remote control. 2. Install remote control batteries correctly. 3. Charge the remote-controlled car. |
| Vehicle Uncontrollable or Short Remote Control Range | 1. Low power in remote control batteries or car's rechargeable battery pack. 2. Interference from nearby sources. |
1. Replace remote control batteries or charge the car's battery. 2. Change the operating venue. |
| Hair Entanglement in Wheels | Foreign objects like dust, debris, and hair on the surface can obstruct movement. | Clean the driving surface. |
| Abnormality Protection (Car's functions hindered by external forces, circuit/battery short-circuited) | External forces hindering movement or circuit/battery short-circuit. | Turn on the power switch again for power-off protection. |
Safety Usage Tips
- When playing indoors, be careful not to damage furniture or glass.
- Play in safe outdoor areas. Do not operate on roads or in crowds to prevent accidents.
- If you hear thunder outdoors, stop using the car immediately.
- Do not drive the car towards people.
- Do not throw or crash the car arbitrarily.
- When storing the car, keep it away from fire sources and high-temperature environments.
- This vehicle uses complex electronic circuits. Do not disassemble, assemble, or modify the circuit board without authorization.
- Regularly check toys, batteries, charging cables, and plugs. Stop use and seek repair if any component is damaged.
- Do not play with the remote-controlled car in sewage pits.
- When the car is moving, do not touch the wheels with your hands to avoid injury.
- Do not play by the roadside or in dangerous places to prevent accidents.
FCC Compliance Information
FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.