Spalding. Made for the Game. | Spalding.com
Owner's Manual for SPALDING models including: M7B62E01 Portable Basketball System, M7B62E01, Portable Basketball System, Basketball System, System
Attach the transport handle (8) to the wheel assembly using the carriage bolts (W8) and nuts (W2). IMPORTANT. Tighten all components completely. #W8. #W2. #8 ...
File Info : application/pdf, 42 Pages, 9.16MB
DocumentDocumentModel Number: (found on product box) PORTABLE BASKETBALL SYSTEM Owner's Manual Toll-Free Customer Service Number U.S.: 1-800-558-5234 Canada: 1-800-284-8339 Europe: +353 51 379777 Australia: 1300 367 582 www.spalding.com WARNING READ AND UNDERSTAND THE OPERATOR'S MANUAL BEFORE USING THIS UNIT. FAILURE TO FOLLOW THE OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY. 05/24 ID# M7B62E01 Contents Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Test-Fit Close Tolerance Bolts . . . . . . . . . . . . . . . . . . . . . . .4 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Tools & Materials for Assembly . . . . . . . . . . . . . . . . . . . . . .9 Assembly Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Assemble the Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Assemble the Wheel Carriage . . . . . . . . . . . . . . . . . . . . . .17 Elevator Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Assemble the Upper Elevator . . . . . . . . . . . . . . . . . . . . . .23 Assemble the Goal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Install The Stadium Pad . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Secure The Assembled Unit for Use . . . . . . . . . . . . . . . . .35 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Questions or Missing Parts? DON'T go back to store! Call TOLL-FREE Customer Service Number listed on the front page! Before You Begin READ AND UNDERSTAND THE OPERATOR'S MANUAL BEFORE USING THIS UNIT. · Remove ALL contents from boxes. · Be sure to check INSIDE pole sections; hardware and additional parts are packed inside. · This manual, accompanied by a sales receipt, should be saved and kept on hand as a convenient reference, as it contains important information about your model. WARNING FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR PROPERTY DAMAGE. Contact Questions or missing parts? Do NOT go back to the store! Email: Customer Service Toll-Free Number: Mailing Address: warrantyservice@custserv.fotlinc.com 1-800-558-5234 Spalding PO Box 90015 Bowling Green, KY 42102 2 Warranty For the very latest Basketball System Warranty information, please visit www.Spalding.com or call Spalding Customer Service at 1-800-558-5234. Warranty Safety Information WARNING FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID THE WARRANTY. Owner must ensure all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check the entire box and inside all of the packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware identifier and parts list in this document. Proper and complete assembly, use, and supervision are essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and operated properly. · If using a ladder during assembly, use extreme caution. · Check the base regularly for leakage. Slow leaks could cause the system to tip over unexpectedly. · Seat the pole sections properly (if applicable). Failure to do so could allow the pole sections to separate during play and/or during transport of the system. · Climate, corrosion, or misuse could result in system failure. · If technical assistance is required, contact Customer Service. · Minimum operational height is 6'-6" (1.98 m) to the bottom of backboard. Most injuries are caused by misuse and/or not following instructions. Use caution when using this unit. NOTICE · Adult assembly required. · Dispose of ALL packaging materials promptly. · As with all products, periodically inspect for loose, small parts. · Assembled unit MUST be filled with sand or water at ALL times. · ALL basketball systems, including those used for DISPLAYS, MUST be assembled and installed according to instructions. · Failure to follow instructions could result in SERIOUS INJURY. · It is NOT acceptable to devise a makeshift support system. Backboard style will vary. NOTE 3 Test-Fit Close Tolerance Bolts Test-Fit Close Tolerance Bolts To ensure optimal playability of the backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to remove any excess paint from holes, if necessary. Not all items pictured are included with every model. NOTE Package Contents Check the contents of each kit and other parts to ensure that all components are present. Keep the kit hardware in the labeled bag as they will be used in different assembly steps. See "Parts List" on page 38 for a complete list of replacement part numbers. BASE ASSEMBLY #1 #4 #3 #6 #5 #2 1 Top Base (x1) 4 Strut, Front, 62.75" Long, with Holes (x2) 2 Bottom Pole Section (x1) 5 Strut, Rear, 62.75" Long (x2) 3 Top Pole Section (x1) 6 Bottom Base (x1) 4 KIT 1 BASE ASSEMBLY BA00006 Package Contents #B1 #B4 #B2 #B3 #B12 #B5 #B6 #B7 #B8 B1 Bolt, Hex Head, 3/8-16x1 L (x4) B4 Bolt, Hex Head, 3/8-16x2-5/8L (x2) B7 Lock-washer, 0.375 ID x 0.675 OD (x4) B2 Washer, Flat, 3/8 x 1 OD (x12) B3 Nut, Hex-Flange, 3/8-16 (x2) B5 Lock-nut, Nylon Insert, 3/8-16 (x4) B6 Lock-nut, Nylon Insert, 1/2-13 (x1) B8 Bolt, Hex Head, 1/2-13x6-5/16L (x1) B12 Drainage Washer, Plastic (x4) KIT 2 POLE ASSEMBLY 208616 #B11 #B10 #B9 B9 Bolt, Hex Head, 5/16-18x5.63x0.91L (x1) B10 Washer, Flat, 5/16 (x2) B11 Nut, Acorn, 5/16-18 (x1) 5 Package Contents WHEEL TO BASE ASSEMBLY #9 #7 #8 #10 #14 #13 #12 #11 #15 7 Wheel, 6" (x2) 10 Bracket, Wheel (x1) 13 Cross Member (x1) 8 Transport Handle, Plastic (x1) 9 U-Bracket, Pivot (x1) 11 Bracket, Pivot, Lower (x1) 12 Disk, Pivot, Plastic (x1) 14 Axle, Rod, 20.5" Long (x1) 15 Tube, Hinged (x2) KIT 3 WHEEL ASSEMBLY BA00005 #W4 #W6 #W2 #W3 #W9 #W10 #W1 #W8 #W5 #W7 W1 Bolt, Hex Head, 3/8-16x3L (x2) W2 Nut, Hex-Flange, 3/8-16 (x12) W3 Washer, 3/8 Flat (x4) W4 Bolt, Hex Head, 3/8-16x2.5L (x2) W5 Bolt, Hex Head, 3/8-16x4.5L (x1) W6 Lock-Nut, 3/8-16 (x2) W7 Bolt, Hex Head, 3/8-16x1L (x1) W8 Bolt, Carriage, 3/8-16 x 2 (x8) W9 Push Caps, Metal, Wheel Assembly (x2) W10 Spacer, 0.379IDx0.5ODx3.5L (x1) 6 ELEVATOR ASSEMBLY #18 #17 16 Handle, Screw-Jack (x1) 19 Cap, Screw Jack (x1) 17 Screw Jack (x1) 20 Pin, Handle (x1) KIT 4 ELEVATOR TO POLE ASSEMBLY EL00002 Package Contents #19 #20 #16 18 Sleeve, Screw Jack (x1) #E1 #E2 E1 Bolt, Hex-Head, 5/16-18x2.75L (x1) E2 Lock-Nut, Nylon Insert, 5/16-18 (x1) BACKBOARD ASSEMBLY #21 #23 #22 21 Elevator Tube, Upper (x1) 24 Plug Cap (x2) 22 Elevator Tube, Lower (x1) #24 23 Backboard (x1) 7 Package Contents KIT 5 BACKBOARD AR00004 #A2 #A5 #A3 #A7 (part scaled for page) #A1 #A4 #A6 A1 Bolt, Hex-Head, 1/2-13x2.25L (x4) A2 Nut, Nylock, 1/2-13 (x7) A4 Bushing, Plastic, 0.50IDx0.25L (x4) A5 Bolt, Hex-Head, 1/2-13x8.4L (x3) A7 Spacer, Plastic, Black 1.7 L (x2) A3 Washer, Flat, 1.08OD (x14) A6 Bushing, Plastic, 0.50IDx0.13L (x4) GOAL ASSEMBLY #27 #28 27 Rim (x1) 28 Net (x1) KIT 6 GOAL 222700 #R1 R1 Bolt, Hex-Flange, 5/16-18x3L (x4) #R2 R2 Washer, 3/8, 1 OD (x4) #R3 R3 Nut, Hex-Flange, 5/16-18 (x4) 8 STADIUM PAD ASSEMBLY #30 #29 #31 #26 P/N 204872 Tools & Materials for Assembly #25 HEIGHT ADJUSTMENT Rotate crank handle to raise and lower backboard. Do not over crank handle beyond the manufactured height indicator range of 7-1/2 - 10 feet. Damage may be caused to the screw jack's internal adjustment mechanism if adjusted over 10 or under 7-1/2 feet. A B MOVING SYSTEM 1. Adjust basketball backboard height to lowest postion. 2. Rotate handle forward until wheels engage ground. 3. Move basketball system to desired location. 4. Rotate handle back to original position. 5. Check system for stability. 1 3 2 4 574090 12/06 25 Label, Height Adjustment and Moving (x1) 30 Stadium Pad, Top (x1) 26 Label, Height Indicator 31 Ground Stake (x1) 29 Stadium Pad, Bottom (x1) KIT 7 STADIUM PAD HARDWARE AC00002 #P1 #P2 P1 Bolt, Carriage, 3/8-16x2.75L (x10) P2 Nut, Hex-Flange, 3/8-16 (x10) Tools & Materials for Assembly 2 Capable Adults Mallet Safety Glasses Socket Wrench 1/2", 9/16", 3/4" Socket Wrench Extension Wrench 1/2", 9/16", 3/4" Phillips Tape Measure Screwdriver #3 Sawhorse Step Ladder (8 ft.) Scrap Wood Board Sand/Garden Hose 9 (OPTIONAL) Adjustable Wrenches Assembly Overview Assembly Overview Backboard (Section E, F) Rim (Section G) Stadium Pad Top (Section C) Stadium Pad Bottom (Section C) Wheel Carriage (Section A) Top Pole (Section B, C) Struts (Section B, C) Elevator System (Section D, E) Bottom Pole (Section B, C) Top Base (Section A, C) Bottom Base (Section B, C) Ground Restraint Rope (Section B, C) 10 Assemble the Base Required Parts: Completed Base Assembly: · Kit 1 · Kit 2 · Scrap Wood Board · 1/2", 9/16", 3/4" Socket Wrench or Wrench · Socket Extension · Mallet Assemble the Base WARNING The following components are factory pre-assembled. CHECK THE PRE-ASSEMBLED AREAS FOR TIGHTNESS. If any parts are missing or damaged please contact our customer service department to receive replacement parts (see customer service information). 11 Assemble the Base PRE-ASSEMBLED COMPONENTS 600074 202900 202900 206340 207585 203331 208253 203309 600200 203041 908624 265523 208253 203309 203331 208253 203309 600200 600075 203309 207692 12 203309 A ASSEMBLE THE BASE 1. Attach the top base (1) to the bottom base using the bolts (B4), washers (B2), drainage washers (B12), and nuts (B3). B4 B2 B12 1 Assemble the Base B12 B2 B3 B ASSEMBLE THE POLE 1. Identify the top (3) and bottom (2) pole sections. 2. Mark 4-5" (10-12.7 cm) from the top of the bottom (2) pole section. 4-5" (10-12 .7 cm) #3 #2 13 Assemble the Base B ASSEMBLE THE POLE CAUTION WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 4-5" (10-12.7 CM) OVERLAP. IF MINIMUM POLE ENGAGEMENT OVERLAP OF 4-5" (10-12.7 CM) CANNOT BE ACHIEVED !! STOP !! DO NOT PROCEED TO THE NEXT STEP! - CALL SPALDING CUSTOMER SERVICE AT 1-800-558-5234 FOR ASSISTANCE. IMPORTANT NOTE THE ORIENTATION OF EACH POLE SECTION. POSITION EACH POLE SECTION SO THAT THE FRONT AND REAR FACES MATCH DIRECTION WHEN ASSEMBLED. 3. Align the top (3) pole section with the bottom (2) pole section and slide together. 4. Bounce the assembled sections on a scrap wood board until the overlap reaches the marked line. 5. Secure the pole sections together using the bolt (B9), washers (B10), and nut (B11). #B11 #B10 #2 (Rear) #B10 #B9 (Rear) #3 REAR REAR #2 #2 #3 #3 FRONT FRONT 14 C INSTALL THE POLE ONTO THE BASE 1. Place the washers (B2) onto the pre-installed bolts. 2. Insert the bottom pole (2) onto the pre-installed bolts through the holes in the bottom pole. 3. Secure the pole assembly to the pole mounting plate using the washers (B2) and nuts (B5). WARNING TWO PEOPLE ARE REQUIRED FOR THIS PROCEDURE . FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE . #2 #B5 #2 Assemble the Base #B2 #B5 #B2 4. Secure the base struts (4 and 5) to the bottom pole (2) using the bolt (B8) and nut (B6). IMPORTANT DO NOT TIGHTEN COMPLETELY. #B6 #4 #5 #2 #4 #B8 #5 15 Assemble the Base C INSTALL THE POLE ONTO THE BASE 5. Rotate the non-secured ends of the base struts (4 and 5) to align with the mounting holes in the base. 6. Secure the ends of the base struts (4 and 5) to the base frame using bolts (B1) and lock washers (B7). IMPORTANT TIGHTEN ALL COMPONENTS COMPLETELY. #5 #4 #B7 #B1 16 Assemble the Wheel Carriage Required Parts: · Kit 3 · Scrap Wood Board · 9/16" Socket Wrench or Wrench · Mallet Completed Wheel Carriage Assembly: Assemble the Wheel Carriage D PREPARE THE BASE FOR THE WHEELS 1. Attach the u-bracket (9) to the cross member (13) using the #W4 bolts (W4), washers (W3), and nuts (W2). IMPORTANT NOTE THE ORIENTATION OF THE BRACKET. #W3 #13 #9 #W2 17 Assemble the Wheel Carriage D PREPARE THE BASE FOR THE WHEELS 2. Secure the cross member (13) to the front struts (4) using the bolts (W1), washer (W3), and nuts (W2) through the bottom set of holes. #4 #W2 #13 #W3 #W1 #9 #W3 #W1 #W2 E ASSEMBLE THE WHEELS 1. Insert the axle (14) through the wheel bracket (10). 2. Secure the wheels (7) to the axle (14) using the push caps (W9). 3. Tap the push caps (W9) onto the axle with a hammer or mallet. #10 #14 #7 #W9 #7 #W9 18 Assemble the Wheel Carriage E ASSEMBLE THE WHEELS 4. Secure the hinge tubes (15) to the wheel bracket (10) using the bolts (W8) and nuts (W2). IMPORTANT DO NOT OVERTIGHTEN. NOTE THE ORIENTATION OF THE TUBES (15) WITH THE SHORT ENDS UNDER THE WHEEL BRACKET. #15 #W8 #15 #W8 #10 #W2 #W2 19 Assemble the Wheel Carriage F INSTALL THE WHEEL ASSEMBLY 1. Secure the lower pivot bracket (11) to the wheel assembly using the bolt (W7), pivot disk (12), and nut (W6). 2. Secure the wheel assembly to the u-bracket (9) using the bolt (W5), spacer (W10), and nut (W6). #W7 #11 #12 #W6 #W10 #9 #W6 #W5 3. Attach the transport handle (8) to the wheel assembly using the carriage bolts (W8) and nuts (W2). Tighten all components completely. IMPORTANT #8 #W2 #W8 20 Elevator Assembly Required Parts: · Kit 4 · 1/2" Socket Wrench or Wrench Completed Elevator Assembly: Elevator Assembly G INSTALL THE ELEVATOR ASSEMBLY 1. Securely rest the assembly on a sawhorse. 2. Slide the screw-jack sleeve (18) over the screw jack and attach the cap (19) to the top end. (Hole faces rear of pole (#2)) #19 #18 21 Elevator Assembly G INSTALL THE ELEVATOR ASSEMBLY 3. Attach the screw-jack to the pole bracket with the bolt (E1) and nut (E2). #E1 #E2 4. Attach the handle (16) to the screw jack with the pin (20). #16 #20 22 Assemble the Upper Elevator Required Parts: · Kit 5 · 3/4" Socket Wrench or Wrench · Socket Wrench Extension · Sawhorse Completed Backboard Assembly: Assemble the Upper Elevator WARNING TWO PEOPLE ARE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. H ATTACH THE ELEVATOR TUBE ASSEMBLY 1. Securely rest the assembly on a sawhorse. Identify the elevator tubes (21 and 22). #22 #21 23 Assemble the Upper Elevator H ATTACH THE ELEVATOR TUBE ASSEMBLY 2. While the system is securely resting on the sawhorse, install the elevator tubes (21 and 22) to the top pole section (3) using the bolts (A5), washers (A3), bushings (A4), and nuts (A2). WARNING TIGHTEN THE BOLTS (A5) IN THE LOCK NUTS (A2) UNTIL FLUSH (EVEN) WITH THE LOCK NUT'S OUTER EDGE. NOTE TEST-FIT THE LARGE BOLTS INTO THE LARGE HOLES OF THE ELEVATOR TUBES AND BACKBOARD BRACKETS. CAREFULLY ROCK THEM IN A CIRCULAR MOTION TO REAM OUT ANY EXCESS PAINT FROM HOLES, IF NECESSARY. #A5 #A3 #A5 #A4 #A3 #A4 #21 #A3 #A2 #22 24 Assemble the Upper Elevator H ATTACH THE ELEVATOR TUBE ASSEMBLY 3. While the system is securely resting on the sawhorse, align the inner metal screw jack (17) bolt holes with the outer plastic screw jack sleeve (18) bolt holes. 4. Install the screw jack assembly to the lower elevator tube (22) using the bolt (A5), washers (A3), spacers (A7), and nut (A2). 5. Reinstall the screw jack cap (19). WARNING TIGHTEN THE BOLT (A5) IN THE LOCK NUT (A2) UNTIL FLUSH (EVEN) WITH THE LOCK NUT'S OUTER EDGE. #A7 #A5 #19 #18 #A7 #A2 #A3 (Sleeve Rear) #A3 #22 I ATTACH THE BACKBOARD 1. Fill the bottom base halfway with water (approx. 25 gallons (95 Liters)) or sand (approx. 295 lbs. (134 kg)). 2. Insert the cap (24) into the base (1) to close. 3. Lower the backboard to the lowest setting and roll the completed assembly to the desired location. #24 #1 ANNOTNIF-TROEXEIZCE 1NGEATLC/3O.7N8TLENTS 25 Assemble the Upper Elevator I ATTACH THE BACKBOARD 4. After system is placed in an upright position, complete the filling process in both bases. 5. Fill the bottom base completely with water (approx. 49 gallons (186 liters)) or sand (590 lbs. (268 kg)). 6. Fill the top base completely with water (approx. 9.8 gallons (37.1 liters)) or sand (approx. 117 lbs. (53.1 kg)). 7. Rotate the caps (24) securely into both the top and bottom bases. ANNOTNIF-TROEXEIZCE 1NGEATLC/3O.7N8TLENTS #24 CAUTION ADD AT LEAST TWO GALLONS (7.6 LITERS) OF NON-TOXIC ANTIFREEZE TO THE WATER OF THE BOTTOM BASE IN SUB-FREEZING CLIMATES. CHECK THE WATER LEVEL BEFORE EACH USE! NOTE IF USING SAND: 2 GALLONS OF ANTIFREEZE IS NOT REQUIRED. 26 Assemble the Upper Elevator I ATTACH THE BACKBOARD 8. Attach the backboard (23) to the elevator tubes (21 and 22) using the bolts (A1), washers (A3), bushings (A6), and nuts (A2). WARNING TIGHTEN THE BOLT (A1) IN THE LOCK NUT (A2) UNTIL FLUSH (EVEN) WITH THE LOCK NUT'S OUTER EDGE. #23 #A6 #A3 #A1 #A3 #A2 #21 #22 27 Assemble the Goal Assemble the Goal Required Parts: · Kit 6 · 1/2", 3/4" Socket Wrench or Wrench · Socket Wrench Extension · Phillips Screwdriver #3 Completed Goal Assembly: J ASSEMBLE THE GOAL 1. Remove the screws that secure the rim cover. #27 28 Assemble the Goal J ASSEMBLE THE GOAL 2. Adjust the backboard to the lowest setting and attach the rim assembly (27) to the board using bolts (R1), washers (R2), and nuts (R3). #27 #R1 #R3 #R2 NOTE If desired, tighten the nut to increase the rim's resistance to movement. #27 29 Assemble the Goal J ASSEMBLE THE GOAL 3. Reinstall the rim cover using the cover screws. #27 4. Thread the net (28) onto the rim (27). #28 #27 #28 #27 #28 #27 #28 #27 30 J ASSEMBLE THE GOAL 5. Apply the Height Adjustment and Moving Label (25) to the front of the pole, where it is clearly visible. #25 HEIGHT ADJUSTMENT Rotate crank handle to raise and lower backboard. Do not over crank handle beyond the manufactured height indicator range of 7-1/2 - 10 feet. Damage may be caused to the screw jack's internal adjustment mechanism if adjusted over 10 or under 7-1/2 feet. A B MOVING SYSTEM 1. Adjust basketball backboard height to lowest postion. 2. Rotate handle forward until wheels engage ground. 3. Move basketball system to desired location. 4. Rotate handle back to original position. 5. Check system for stability. 1 3 2 4 574090 12/06 6. Apply the Height Indicator Labels (26) to the screw jack. 7. Adjust the height to 7-1/2 feet (2.3 m) from the top of the rim to the playing surface. 7-1/2 8. Place 7-1/2 feet (2.3 m) sticker to the middle of the hole of the screw jack sleeve. 9. Repeat for each subsequent height until the last sticker is in place at the 10 foot (3.05 m) height. Assemble the Goal #26 P/N 204872 31 Assemble the Goal J ASSEMBLE THE GOAL 10. Rotate the crank handle to move the backboard up or down to the desired height. WARNING DO NOT ALLOW CHILDREN TO ADJUST THE HEIGHT. DO NOT OVER CRANK THE HANDLE BEYOND THE HEIGHT INDICATOR RANGE OF 7-1/2 TO 10 FEET (2.3 TO 3.05 M) OR THE ADJUSTMENT MECHANISM MAY BE DAMAGED. 32 Install The Stadium Pad Required Parts: Complete Unit Assembly: · Kit 7 · 9/16" Socket Wrench or Wrench Install The Stadium Pad K INSTALL THE STADIUM PAD 1. Attach the top stadium pad (30) to the front strut (4) using the bolts (P1) and nuts (P2). #P1 #30 #P2 #4 33 Install The Stadium Pad K INSTALL THE STADIUM PAD 2. Slide the bottom stadium pad (29) behind the transport handle (8) and secure using the bolts (P1) and nuts (P2). #P1 #P2 #8 #29 34 Secure The Assembled Unit for Use Secure The Assembled Unit for Use Required Parts: · Water · Sand Complete Unit Assembly: WARNING · TWO CAPABLE ADULTS ARE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY. · DO NOT LEAVE THE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. · FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. · THE CAP (24) MUST BE TIGHTENED COMPLETELY AND SECURELY TO PREVENT LEAKAGE. · CONTACT CUSTOMER SERVICE IMMEDIATELY IF THE CAP IS MISSING OR DAMAGED. · CHECK THE WATER LEVEL BEFORE EACH USE. 35 Secure The Assembled Unit for Use L SECURE THE GROUND STAKE 1. Place the system in the desired location. 2. Stretch the rope tight to determine the ground stake (31) location. 3. Install the ground stake (31) into the ground. 4. Loop the eyelet of the rope onto the eyelet of the ground stake (31). #31 36 Operation M ADJUSTING THE HEIGHT 1. Rotate the crank handle to move the backboard up or down to the desired height. WARNING DO NOT ALLOW CHILDREN TO ADJUST THE HEIGHT. DO NOT OVER CRANK THE HANDLE BEYOND THE HEIGHT INDICATOR RANGE OF 7-1/2 TO 10 FEET (2.3 TO 3.05 M) OR THE ADJUSTMENT MECHANISM MAY BE DAMAGED. Operation N MOVING THE UNIT 1. Adjust the basketball backboard height to the lowest postion. 2. Rotate the handle forward until the wheels engage the ground. 3. Move the basketball system to the desired location. 4. Rotate the handle back to its original position. 5. Check the system for stability. 37 Parts List Parts List #A2 #23 #A1 #A4 #A3 #21 #A7 #A3 #A5 ##2257 #R1 ##2268 #P1 #R3 #A2 #A6 #R2 ##3205 #22 #3 #B11 #B10 ##2380 #P1 #P2 #2 ##2279 #8 #P2 #5 #4 #E2 #E1 #B9 #19 #18 ##3216 #B5 #17 #16 #B2 #20 #B6 #B8 ##2391 #W8 #15 #W9 #11 #12 #W7 #W2 #W6 #7 #W8 #13 #10 #B4 #B2 #B12 #1 #B12 #B3 #W4 #W3 #14 #W2 #W3 #W6 #W10 #W5 #W2 #W1 #9 #W2 #24 #B1 #6 #4 #5 #B7 38 Parts List Item Qty 1 1 Part No . 6000761 Description Top Base 2 1 901183 Bottom Pole Section 3 2 901184 Top Pole Section 4 2 908459 Strut, Front, 62.75" L, with Holes 5 2 908699 Strut, Rear, 62.75" L 6 1 700376 Bottom Base 7 2 600074 60007901 8 1 60007902 9 1 800373 Wheel, 6" Transport Handle, Gray Transport Handle, Black U-Bracket, Pivot 10 1 908466 Bracket, Wheel 11 1 206948 Bracket, Pivot, Lower 12 1 206956 Disk, Pivot, Plastic 13 1 908513 Cross Member 14 1 20694001 Axle, Rod, 20.5" L 15 2 908460 Tube, Hinged 16 1 700009 Handle, Screw-Jack 17 1 80034403 Screw Jack 18 1 60016401 Sleeve, Screw Jack 19 1 600165 Cap, Screw Jack 20 1 202528 Pin, Handle 21 1 908508 Elevator Tube, Upper 22 1 908509 Elevator Tube, Lower 23 1 Backboard 24 2 25 1 26 1 266300 574090 204872 Plug Cap Label, Height Adjustment and Moving Label, Height Indicator Item Qty 27 1 28 1 29 1 30 1 31 1 Part No . 600077 600078 203124 Description Rim Net Stadium Pad, Bottom Stadium Pad, Top Ground Stake A1 4 205711 Bolt, Hex-Head, 1/2-13 x 2 .25" L A2 7 A3 14 A4 4 A5 3 A6 4 A7 2 B1 4 B2 12 B3 2 B4 2 B5 4 B6 1 B7 4 B8 1 B9 1 B10 2 B11 1 B12 4 E1 1 E2 1 206340 203474 Nut, Nylock, 1/2-13 Washer, Flat, 1 .08" OD 201651 Bushing, Plastic, 0 .50 IDx0 .25" L 207876 Bolt, Hex-Head, 1/2-13 x 8 .4" L 208251 Bushing, Plastic, 0 .50 IDx0 .13" L 204620 Spacer, Plastic, Black 1 .7" L 265523 Bolt, Hex Head, 3/8-16 x 1" L 203309 Washer, Flat, 3/8 x 1 OD 203041 Nut, Hex-Flange, 3/8-16 265563 Bolt, Hex Head, 3/8-16 x 2-5/8" L 203063 Lock-nut, Nylon Insert, 3/8-16 206340 202602 206304 208617 203218 Lock-nut, Nylon Insert, 1/2-13 Lock-washer, 0 .375 ID x 0 .675 OD Bolt, Hex Head, 1/2-13 x 6-5/16" L Bolt, Hex Head, 5/16-18 x 5 .63 x 0 .91" L Washer, Flat, 5/16 207610 Nut, Acorn, 5/16-18 209532 201518 203099 Drainage Washer, Plastic Bolt, Hex-Head, 5/16-18 x 2 .75" L Lock-Nut, Nylon Insert, 5/16-18 39 Parts List Item Qty P1 10 P2 10 R1 4 R2 4 R3 4 W1 2 W2 12 W3 4 Part No . 206011 Description Bolt, Carriage, 3/8-16 x 2 .75" L 203041 Nut, Hex-Flange, 3/8-16 201611 Bolt, Hex-Flange, 5/16-18 x 3" L 203309 Washer, 3/8, 1" OD 203100 Nut, Hex-Flange, 5/16-18 200514 Bolt, Hex Head, 3/8-16 x 3" L 203041 Nut, Hex-Flange, 3/8-16 203299 Washer, 3/8 Flat Item Qty W4 2 Part No . 265563 Description Bolt, Hex Head, 3/8-16 x 2 .5" L W5 1 203330 Bolt, Hex Head, 3/8-16 x 4 .5" L W6 2 203063 Lock-Nut, 3/8-16 W7 1 206252 Bolt, Hex Head, 3/8-16 x 1" L W8 8 W9 2 W10 1 203277 207550 202274 Bolt, Carriage, 3/8-16 x 2" Push Caps, Metal, Wheel Assembly Spacer, 0 .379 ID x 0 .50 OD x 3 .5" L 40 41 SAFETY LABELS NOTICE APPLY THE SAFETY LABELS TO THE COMPLETED ASSEMBLY PRIOR TO USE. HEIGHT ADJUSTMENT Rotate crank handle to raise and lower backboard. Do not over crank handle beyond the manufactured height indicator range of 7-1/2 - 10 feet. Damage may be caused to the screw jack's internal adjustment mechanism if adjusted over 10 or under 7-1/2 feet. A B MOVING SYSTEM 1. Adjust basketball backboard height to lowest postion. 2. Rotate handle forward until wheels engage ground. 3. Move basketball system to desired location. 4. Rotate handle back to original position. 5. Check system for stability. 1 3 2 4 574090 12/06 WARNING Read and understand warnings listed below before using this product. Failure to follow these warnings may result in serious injury and/or property damage. Owner must ensure that all players know and follow these rules for safe operation of the system. · DO NOT HANG on the rim or any part of the system including backboard, support braces or net. · During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net. · Do not slide, climb, shake or play on base and/or pole. · After assembly is complete, fill system completely with water or sand and stake to the ground. Never leave system in an upright position without filling base with weight, as system may tip over causing injuries. · When adjusting height or moving system, keep hands and fingers away from moving parts. · Do not allow children to move or adjust system. · During play, do not wear jewelry (rings, watches, necklaces, etc.). Objects may entangle in net. · Surface beneath the base must be smooth and free of gravel or other sharp objects. Punctures cause leakage and could cause system to tip over. · Keep organic material away from pole base. Grass, litter, etc. could cause corrosion and/or deterioration. · Check pole system for signs of corrosion (rust, pitting, chipping) and repaint with exterior enamel paint. If rust has penetrated through the steel anywhere, replace pole immediately. · Check system before each use for proper ballast, loose hardware, excessive wear and signs corrosion and repair before use. · Check system before each use for instability. · Do not use system during windy and/or severe weather conditions; system may tip over. Place system in the storage position and/or in an area protected from the wind and free from personal property and/or overhead wires. · Never play on damaged equipment. · See instruction manual for proper installation and maintenance. · When moving system, use caution to keep mechanism from shifting. · Keep pole top covered with cap at all times. · Do not allow water in tank to freeze. During sub-freezing weather add 2 gallons of non-toxic antifreeze, sand or empty tank completely and store. (Do not use salt.) · While moving system, do not allow anyone to stand or sit on base or have added ballasting on base. · Do not leave system unsupervised or play on system when wheels are engaged for moving. · Use Caution when moving system across uneven surfaces. System may tip over. · Use extreme caution if placing system on sloped surface. System may tip over more easily. In the U.S.: 1-800-558-5234 In Canada: 1-800-284-8339 In Australia: 1-300-367-582 In the U.S.: 1-800-558-5234 In the U.S.: 1-800-334-9111 Trademarks registered in the USA and other countries. ID#: 55679001 02/12 In the U.S.: 1-800-558-5234 In Canada: 1-800-284-8339 © Copyright 2024 by Russell Brands, LLC www .Spalding .com