Instruction Manual for PowerQuest models including: 18789 Touch Screen Control System Switch Panel, 18789, Touch Screen Control System Switch Panel, Screen Control System Switch Panel, Control System Switch Panel, System Switch Panel, Switch Panel
Tech Support
1411 S. Roselle Rd. Schaumburg, IL 60193 Phone (847) 923-0002 Fax (847) 923-0004 www.AltronicsInc.com Pump and back to 100º to turn on again)
File Info : application/pdf, 6 Pages, 915.74KB
DocumentDocumentThe Touch Screen Control System consists of two components, the Touch Screen (TS) and the Switch Panel Module(SPM). The PowerQuest system can control the switching of 8 circuits. Each circuit can be fused up to 30 amps. The system should be installed be a certified automotive technician. Connect GROUND wire first!!!! Power LED - Solid (OK) Status LED - Blinking (OK) Mount touch screen using template Connect cable from back of TS to Module Mount module to electronics panel using supplied bolts. 1411 S. Roselle Rd. Schaumburg, IL 60193 Phone (847) 923-0002 Fax (847) 923-0004 www.AltronicsInc.com WiringSystem: Terminals 2 and 3: Connect to Temperature sensor (included). Battery + : Use minimum 4 AWG cable. Connect to Positive Post on Battery IMPORTANT: Install independent cable direct to battery or battery disconnect switch (kill switch). Do not splice from another power cable or junction. Max torque on nuts: 24 inch-lb (2 ft-lb)!!! Ground Terminal: Use #12 AWG Wire. (Recommend to Battery Negative Post or Good Chassis Ground Point) Connect this wire first! For Circuits (Starter, Ignition, Fuel, etc..) use appropriate 14awg (30 amp), 16awg (20 amp), or 18awg (15 amp) wire depending on load. Connect Cable from Touch Screen IGN Ctrl Connect ignition signal or other switched signal to IGN Ctrl terminal. This input will allow (Trig enabled (IGN)) channels to turn on/off when ignition is turned on/off. Also, ignition can control system power up and down if Ignition/Switch Power off is enabled in SETUP menus (see Configure section) Trig1 Trig 2 This input will allow (Trig enabled) channels to turn on/off when Trig 1 or Trig2 signal is turned on/off. Feature must be enabled in SETUP menus (see Configure section) 1411 S. Roselle Rd. Schaumburg, IL 60193 Phone (847) 923-0002 Fax (847) 923-0004 www.AltronicsInc.com Configure: System will be Configured with default settings. To change those settings press the "Config" button on the switch panel screen. Brightness Sets screen brightness Sleep Turns screen off when no user press for sleep time. Press anywhere on screen to turn back on. Can also be controlled by ignition signal. Security Enable Activates optional Lock Screen and Manual Sleep. Enable 16 Ch Activates second module when installed Ign/Switch Power Enables external ignition or switch input into external IGN terminal to control system power up and down (Sleep). Display Amps Activates displaying current level for each switch channel. Blue Tooth Bluetooth setup for BT control, optional. Select Channel- Press to see list of available switch Channels, then select channel to modify Not all features are available for all circuits. Channel Displays channel name. Pick button: Use +/- buttons to cycle thru preset buttons Custom button: Select to enter custom label for button. Soft Start: Check box to allow slow increase in current at turn on. Switch Type: Select switch behavior. Normal, Momentary, Pulse (turn signal), Burst (high speed pulse, with pause), SOS (distress pulse), Dim/PWM (Select 0-100% power for dimming lights or running motor at different speeds) Max Current: Select maximum fused amperage for circuit (0-30amps). Limit Enabled: Check box to limit circuit turn on by temperature settings Temperature: Select temperature to enable. Hysteresis: Differential temperature change required to activate. (Ex: With a 2º hysteresis and a 100º temperature setting the controller will allow the actual temperature to go to 98º before turning off Fan and Pump and back to 100º to turn on again) allow the actual temperature to go to 98º before turning off Fan and 1411 S. Roselle Rd. Schaumburg, IL 60193 Phone (847) 923-0002 Fax (847) 923-0004 www.AltronicsInc.com Pump and back to 100º to turn on again) Auto Enable: Check to enable. Allows switch channel to automatically turn on and off other selected channels when activated/deactivated. Auto Switch Delay: Time in seconds selected circuit is delayed from turning on if it is Auto Enabled from another channel. Trig Enable: External control to turn channel on or off. Requires wired connection to IGN (ignition), Trig 1 or Trig 2 terminals on module. Save: Saves changes and returns to previous Menu. Lock Screen: Master Code: On the back of Module (not the touch screen) there is a tag with the systems Master 4 digit program code and a Temporary User Code. You can use the Master code to program your User code. The Master code can always be used to reset User code. Reset User Code: Use following sequence to program User Code. 1) User code cannot be Master Code or 1234. 2) Key in Master Code and press ENTER 3) Use Back arrow to delete Master Code from window. 4) Key in number USER CODE XXXX and press ENTER 5) Press Enter Again Now User Code is set. Unlock Screen: Key in User code and press ENTER SLEEP: Press Sleep to force sleep mode. 1411 S. Roselle Rd. Schaumburg, IL 60193 Phone (847) 923-0002 Fax (847) 923-0004 www.AltronicsInc.com If fuse is tripped Switch Panel circuit button will turn off and "FUSE" message will be shown on button label. Pressing button again will reset fuse. PowerQuest Demonstration video (www.altronicsinc.com/switch-panels/powerquest-1.html) for more details. TECHNICAL SUPPORT: Email: Tech@AltronicsInc.com When sending a unit in for repair or update: Fill out a "Service Form" which is available from the Technical Support Section of our website-> www.AltronicsInc.com WARRANTY: by is warranted for 1 Year against any defect in materials and workmanship from date of purchase. ALL WARRANTIES AND GUARANTEES ARE VOID if the connected to system that is not supplied or authorized by Altronics Inc. enclosures are opened or altered or if equipment is shall not be liable for injury, consequential, or other types of damages resulting from the use or misuse of the is to be used for off road purposes only! 1411 S. Roselle Rd. Schaumburg, IL 60193 Phone (847) 923-0002 Fax (847) 923-0004 www.AltronicsInc.com Verify the size of this print against dimensions given before use!
mailto:tech@altronicsinc.com
Drag Racing Weather Stations, Data Loggers, EGT, Air/Fuel, Wideband, & Lithium Batteries - Altronics
Drag Racing Weather Stations, Data Loggers, EGT, Air/Fuel, Wideband, & Lithium Batteries - Altronics