Support Center - AIDA Imaging
User Guide for AIDA models including: UHD6G-200 UHD 6G-SDI POV Camera, UHD6G-200, UHD 6G-SDI POV Camera, POV Camera, Camera
Reproduction of this manual, in whole or in part, by any means, is prohibited. Version 1.0 / April 2020 UHD 6G-SDI POV Camera OPERATION GUIDE UHD6G-200
File Info : application/pdf, 20 Pages, 276.28KB
DocumentDocumentUHD 6G-SDI POV Camera UHD6G-200 OPERATION GUIDE Version 1.0 / April 2020 Reproduction of this manual, in whole or in part, by any means, is prohibited. CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. PRECAUTION This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture. 1. Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product. 2. Incorrectly connecting the power supply or replacing battery may cause explosion,cause excessive heat or fire 3. Securely plug the power cord into the power receptacle. Insecure connection may cause fire. 4. Do not place conductive objects (e.g. screw drivers, coins, metal items, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects. Continue on Next Pa2ge Warning continues 5. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock 6. If any unusual smells or smoke come from the unit, stop using the product. Immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock. 7. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. 8. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock. PRECAUTION Please read this Operation Guide before installing and using the camera & retain this copy for your reference. 1. Always follow the instructions in the operations guide when applying power. Fire and equipment damage can occur if power is applied incorrectly. For the correct power supply,refer to the specifications page. 2. Do not use camera if fumes, smoke or a strange odor is emitted from the camera, or if it seems not functional correctly. Disconnect the power source immediately and consult with your supplier. 3. Do not use the camera in extreme environments where high temperatures or high humidity exists. Use the camera under conditions where temperatures are between 32°F ~ 104°F, and humidity is below 90%. 4. If installed close to a TV, radio transmitter, magnet, electric motor transformer or audio speakers the magnetic field generated may interfere with or distort the image. 5. Try to avoid fluorescent light reflections, unstable light conditions, direct pointing toward the sun. Use caution when operating the camera in the vicinity of spotlights or other bright lights and light reflecting objects. 6. To prevent damage, do not drop the camera or subject it to strong shock or vibration. 3 UHD6G-200 4 FEATURES · 4K UHD 1/2.5 Progressive Scan CMOS sensor captures sharp and vivid UHD video even under low light conditions. · Advanced digital imaging processor provides vivid and detailed images by utilizing Dynamic Range, Auto White Balance, and Noise Reduction. · Superb motion-compensated temporal noise reduction filter for motion video without blurring. · OSD control breakout cable with power input and RS-485 for remote communication. · Flawlessly relays multi-channel embedded audio via SDI output. · Interchangeable lens design compatible with CS and C mount lenses. · Perfectly suited for broadcast, pro audio/video, and security. · Conforming with SMPTE 292M, 424M, and 2081-10. · Versatile, compact, and rugged design. OSD MENU MAIN MENU *WB CONTROL AE CONTROL DAY /NIGHT AUDIO IMAGE CONTROL SPECIAL SETUP RESET EXIT L- Left | R- Right | U- Up | D- Down | - Select 1. Move the Cursor Up/Down to Choose Menu To move from item to item in the menu, move the joystick to the Up/Down. 2. Change the Value To change the value of the selected item, move the joystick to the Left/Right. 3. Shift to the Sub Menu of the Chosen Menu To go into sub menu, press SEL key. The menu items with > always have its sub menu. 5 EXPOSURE EXPOSURE *AE MODE SHUTTER IRIS AGC AGC MAX SENS UP AE BRIGHT IRIS SPEED FLK CONTROL LENS MODE RETURN AUTO HIGH OFF 6 3 OFF INDOOR EXPOSURE *AE MODE SHUTTER IRIS AGC AGC MAX SENS UP AE BRIGHT IRIS SPEED FLK CONTROL LENS MODE RETURN SHUT FIX AUTO HIGH OFF 6 3 AUTO INDOOR AUTO Auto mode will adjust the exposure level automatically. Detailed fine tuning options are available under this menu. · AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX "AGC MAX" sets the maximum gain value to control the video noise caused by Auto Gain Control. · SENS UP : OFF, x2 ~ x10 "SENS UP" mode controls the digital slow shutter to allow extra light into the camera and adjust the picture quality. · AE BRIGHT : 0~20 Auto Exposure brightness level can be adjusted. SHUT FIX SHUT FIX mode provides more detailed shutter speed option. All other controls are tuned for the selected shutter speed. · SHUTTER : AUTO, 1/30 ~ 1/10,000 ( Shutter speed can be set ) · AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX "AGC MAX" sets the maximum gain value to control the video noise caused by Auto Gain Control. · SENS UP : 0~20 "SENS UP" mode controls the digital slow shutter to allow extra light into the camera and adjust the picture quality. · AE BRIGHT : 0~10 Auto Exposure brightness level can be adjusted 6 EXPOSURE EXPOSURE *AE MODE SHUTTER IRIS AGC AGC MAX SENS UP AE BRIGHT IRIS SPEED FLK CONTROL LENS MODE RETURN AGC FIX AUTO HIGH 6 3 AUTO INDOOR AGC FIX AGC FIX mode provides more detailed gain option. All other controls are tuned for the selected gain value. · AGC : AUTO, 0dB ~ 27dB, d2X ~ d9X Gain level can be set. · AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX "AGC MAX" sets the maximum gain value to control the video noise caused by Auto Gain Control. · AE BRIGHT : 0~10 Auto Exposure brightness level can be adjusted. · IRIS SPEED : 0 ~ 5 Electronic Iris speed can be controlled. ( DC Iris lens only ) · LENS MODE : INDOOR, OUTDOOR, MANUAL Lens setting will be optimized for the selected environment. ( DC Iris lens only ) · FLK CONTROL : AUTO, ON, OFF "FLK CONTROL" mode provides a proper image sensor frequency to match the power frequency in order to minimize video flicker. 7 WHITE BALANCE WHITE BALANCE *MODE PUSH BLUE RED SPEED OFFSET-B OFFSET-R RETURN AT W 6 52 54 WHITE BALANCE *MODE PUSH BLUE RED SPEED OFFSET-B OFFSET-R RETURN ONE PUSH PRESS OK 52 54 ATW Auto trace white mode will adjust white balance within 1,900~K ~ 11,000~K temperature. · SPEED : 0 ~ 7 White balance adjust speed can adjusted. · OFFSET-B : 0 ~ 100 "OFFSET-B" adjusts Blue gain within the range of 0 to 100. · OFFSET-R : 0 ~ 100 "OFFSET-R" adjusts Red gain within the range of 0 to 100. ONE PUSH One push mode is used if AWB or ATW cannot produce the proper white balance. Place a white paper in front of the camera when using the one push mode to self adapt. · PUSH Press Select button to enable "ONE PUSH" white balance adjustment. Place a white paper in front of the camera when using the "ONE PUSH" mode to self-adopt. * Camera provides a wide range of white balance options. Check your color temperature before adjusting this mode. 8 WHITE BALANCE WHITE BALANCE *MODE PUSH BLUE RED SPEED OFFSET-B OFFSET-R RETURN INDOOR 52 54 WHITE BALANCE *MODE PUSH BLUE RED SPEED OFFSET-B OFFSET-R RETURN MANUAL 50 50 INDOOR "INDOOR" mode will adjust white balance to indoor lighting conditions. OUTDOOR "OUTDOOR" mode will adjust white balance to outdoor lighting conditions. MANUAL "MANUAL" mode will adjust white balance manually. · BLUE - 0 ~ 100 Select blue gain within the range of 0 to 100. · RED - 0 ~ 100 Select Red gain within the range of 0 to 100. 9 DAY & NIGHT DAY & NIGHT *MODE NIGHT COLOR COLOR BURST RETURN DAY (COLOR) OFF OFF NOISE REDUCTION *MODE DNR LEVEL DNR APERTURE RETURN 2D + 3D AUTO 2 Adjust color or B&W setting from this menu. · MODE : DAY(COLOR), NIGHT(B&W) Set camera to either color mode or B&W mode. · NIGHT COLOR : ON, OFF When "NIGHT COLOR" is turned ON, camera stays on color mode even "NIGHT(B&W)" is selected from the MODE. · COLOR BURST : ON, OFF Color burst signal ON or OFF can be set for CVBS signal. ( Not applicable ) DNR NOISE REDUCTION Camera noise level can be adjusted from this menu. · DNR MODE : OFF, 2D, 3D, 2D+3D Digital noise reduction can be applied from this menu. · DNR LEVEL : AUTO, LOW, MIDDLE, HIGH Noise reduction level can be adjusted from this menu. · DNR APERTURE : 0 ~ 4 Motion artifacts tightness can be adjusted. 0 = Most ghost artifact 4 = Least ghost artifact 10 PRIVACY PRIVACY MASK *MODE TYPE MASK NO. DISPLAY COLOR POLY PIXEL POSITION-X POSITION-Y SIZE-X SIZE-Y DEFAULT RETURN ON SQUARE MASK 1 ON BLACK 2 5 20 11 Privacy zone can be setup from this menu. MODE : ON, OFF Enable "PRIVACY ZONE" ON or OFF. TYPE : SQUARE, POLYGON Select privacy zone shape. MASK NO : MASK1 ~ MASK8 Select privacy zone mask number. DISPLAY : ON, OFF Turn ON or OFF the selected privacy mask zone. COLOR : WHITE, GREEN, BLUE, RED, CYAN, MAGENTA, YELLOW, GRAY-1 ~ 6, MOSAIC, BLACK. ( Select privacy zone mask color ) POLY SELECT : L- TOPP, L- BOTTOM, R- TOP, R-BOTTOM Change the shape of the polygon by selecting the corner of the polygon. POSITION-X & POSITION-Y Change the size of the selected corner from "POLY SELECT" menu. SIZE-X & SIZE-Y Change the size of the privacy square. DEFAULT Set privacy zone to default value. 11 EFFECT EFFECT LENS SHADING ON *GAMMA CORRECT ON CONTRAST 11 BRGIAGHMTMNAESSCORREC1T1ION OPTION SA*TFURROANTTIOGNM EN 12 DEFAULT HUEREAR GM EN 10 EDGREEAERNHGAMNCIENV 5 DEFAULT AUTBOAYSALTUUTRAETXITOENND MIDUDNLIEFORM AUTBOAYEDLGUET EXTEND ON UNIFORM DEFYAULLUTT EXTEND UNIFORM RETBUYRLNUT XSAMPLE 64X256LUT RGBLUT XSAMPLE 64X256LUT RETURN EFFECT LENS SHADING GAMMA CORRECT *CONTRAST BRIGHTNESS SATURATION HUE EDGE ENHANCE AUTO SATURATION AUTO EDGE DEFAULT RETURN ON ON 11 11 12 10 5 MIDDLE ON Camera image control can be adjusted from EFFECT menu. LENS SHADING : ON, OFF Optical vignetting issue can be corrected from this menu. GAMMA CORRECT : ON, OFF (1.0) Gamma level can be adjusted. · Y LUT EXTEND : UNIFORM, EXTEND-F2C Tuning and engineering purpose LUT correction. · BYLUT XSAMPLE : 64x256LUT, 32x256LUT, 64x256LUT, 128x256LUT, 256x256LUT Tuning and engineering purpose LUT correction. · RGBLUT XSAMPLE: 64x256LUT, 32x256LUT, 64x256LUT, 128x256LUT, 256x256LUT Tuning and engineering purpose LUT correction. · CONTRAST : 0 ~ 20 ( Contrast level can be adjusted ) · BRIGHTNESS : 0 ~ 20 ( Brightness level can be adjusted ) · SATURATION : 0 ~ 20 ( Saturation level can be adjusted ) · HUE : 0 ~ 20 ( Hue level can be adjusted ) · EDGE ENHANCE : 0 ~ 20 ( Image sharpness level can be adjusted ) · AUTO SATURATE : OFF, LOW, MIDDLE, HIGH Decrease saturation automatically when noisy scene is detected. · AUTO EDGE : ON, OFF Decrease edge enhancement (sharpness) automatically when noisy scene is detected. · DEFAULT : See Effects menu to default value. 12 SPECIAL SPECIAL *DZOOM OFF DEFOG OFF DWDR OFF MOTION DETECT OFF BACKLIGHT OFF BINNING OFF DEFECT PIXEL ON DISP. FUNCTION FLICKER DETECT OFF PRIVACY RETURN D-ZOOM *ZOOM CONTROL PIP PIP SIZE PIP POSITION DZOOM SAVE DEFAULT RETURN OFF 1/16 Camera special functions can be adjusted from SPECIAL menu. D ZOOM : ON, OFF ( Digital Zoom and PIP function can be enabled from this menu ) · ZOOM CONTROL : RATIO, POSITION, RETURN Adjust the digital zoom ratio and position. Use LEFT / RIGHT button to adjust the ratio, then press select. USE LEFT / RIGHT/ UP / DOWN button to adjust the image position, then press select. Press select to exit. · PIP : ON, OFF ( Turn ON or OFF the PIP window ) · PIP SIZE : 1/16, 1/25 ( Change the size of PIP window ) · PIP POSITION : POSITION, RETURN ( Adjust the PIP window location ) USE LEFT / RIGHT/ UP / DOWN button to adjust the image position,then press select. Press select to exit. · DEFAULT : Set privacy zone to default value. 13 SPECIAL DEFOG SETUP *STRENGTH 4 THRESHOLD AUTO LEVEL RETURN BACKLIGHT - BLC *BLC ON SIZE/POSITION DISPLAY ON DEFAULT RETURN DEFOG : ON, OFF, AUTO "DEFOG" menu improves foggy image. · STRENGTH : 0 ~ 16 Change defog strength. · THRESHOLD : 0 ~ 3 Threshold value sets minimum sensitivity value for automatic defog control. Higher value makes defog-on control reluctant. · AUTO LEVEL : LOW, MID, HIGH Auto level value sets maximum strength value for automatic defog control. Higher value makes defog effect to be stronger. DIS : Digital image stabilization can be turned ON or OFF. BACK-LIGHT : OFF, BLC, HLM - Camera back-light compensation can be adjusted. BLC : OFF, ON - BLC enables back light compensation. · SIZE/POSITION : SIZE, POSITION, RETURN Adjust BLC area window size. · DISPLAY : OFF, ON BLC area display can be turned ON or OFF · DEFAULT : Set BLC menu to default value. 14 SPECIAL BACKLIGHT - HLM AREA ON *AREA DISPLAY ON SIZE/POSITION LEVEL 3 BLACK MASK ON DEFAULT RETURN DEFECT PIXEL *STATIC PROGRESS SDPC UPDATE SDPC CLEAR RETURN PRESS OK PRESS OK PRESS OK HLM : OFF, ON HLM can be adjusted. · AREA DISPLAY : ON, OFF HLM AREA DISPLAY can be turned ON or OFF. · SIZE/POSITION : SIZE, POSITION, RETURN Adjust BLC area window size. · LEVEL : 0 ~ 20 Amount of masking area can be adjusted. · BLACK MASK : OFF, ON Masking area highlight can be turned ON or OFF. · DEFAULT : Set HLM menu to default value. BINNING : OFF, ON Binning can be turned ON or OFF. DEFECT PIXEL : OFF, ON, ON (FIXED), STATIC Defective Pixel Correction feature can be operated. It is turned ON by default and will run both dynamic and static DPC function. 15 SPECIAL DISPLAY FUNCITON *FREEZE MIRROR IMAGE EFFECT ROTATION PICTURE STYLE RETURN OFF MIRROR NEGATIVE ROT VIVID SPECIAL DZOOM DEFOG OFF DIS OFF BACKLIGHT OFF BINNING DEFECT PIXEL OFF DISP. FUNCTION RT *FLICKER DETECT ON RETURN ZOOM DISPLAY FUNCTION : OFF, ON Adjust image display features from this menu. · FREEZE : OFF, ON Image freeze can be turned ON or OFF. · MIRROR : OFF, MIRROR, V-FLIP, BOTH(H/V) Image mirror or flip can be operated. · IMAGE EFFECT : OFF, NEGATIVE, GREY MODE, REDDISH-1 ~ 4, BLUISH-1 ~ 4, GREENISH-1 ~ 4.ROTATION : OFF, ROT_L 1:1 Several color effects can be applied. · ROTATION : OFF, ROT_L FULL, ROT_L 1:1, ROT_R Full, ROT_R 1:1 Image can be rotated either left or right side. · PICTURE STYLE : OFF, STANDARD, VIVID, CLEAR, VIVID CLEAR, NEUTRAL Different types of picture style can be applied. FLICKER DETECT : OFF, ON "FLICKER DETECT" mode provides a proper image sensor frequency to match the power frequency in order to minimize video flicker. 16 SETUP SETUP *CAM TITLE RS485 MENU COLOR FACTORY RESET SYSTEM INFO OUTPUT FORMAT RETURN OFF 1080P60 Camera setup can be adjusted from this menu. CAM TITLE : OFF, ON Camera title can be turned ON or OFF. RS-485 : VISCA communication control can be adjusted. · CAM ID : 0 ~ 7 Camera ID can be setup. · ID DISPLAY : OFF, ON Camera ID can be setup. · BAUDRATE : 2400, 4800, 9600, 19200, 38400 Camera baudrate can be set. SYSTEM INFO : ON, OFF, AUTO Camera information can be found under this menu. OUTPUT FORMAT : ON, OFF, AUTO Camera resolution and frame rate can be set MENU COLOR : OSD menu color can be adjusted. Supported formats are: * 1080p by default 4K2160P - 30 / 29.97 25 / 24 1080P - 60 / 59.94 50 30/ 29.97 / 25 / 24 1080I - 60 / 59.94 / 50 720P - 60 / 59.94 / 50 AUDIO Audio input [MIC or LINE] can be selected, and level can be adjusted under this menu. 17 SPECIFICATION VIDEO Image Sensor 1/1.7" Progressive CMOS Sensor Size Diagonal 9.93mm(17:9) Effective Pixels Horizontal: 4096, Vertical: 2160 Pixel Size 1.85 µm x 1.85 µm Resolution 4096 x 2160, 3840 x 2160, 1920 x 1080, 1280 x 720 Resolution Rate 4K (4096 X 2160) 60/59.94/50/30/29.97/25/24 3840p 60/59.94/50/30/29.97/25/24p 1080p 60/59.94/50/30/29.97/25p/24p 1080i 60/59.94/50i 720 60/59.94/50p Output HDMI 2.0 Color Space 4:2:2 (YCbCr) 10bit LENS Lens C/CS Mount (with 4K 3.6mm - 11mm varifocal lens) AUDIO INPUT Input 3.5mm TRS Stereo Mic-in & Line in over I/O Cable Sample Rate 16/24/32 Bits STANDARD SMPTE SMPTE 292M, SMPTE 424M PHYSICAL Camera Control RS-485 VISCA, OSD Button Operation Temp 15° F - 120° F Dimension 51mm x 51m x 102mm / 2.01" x 2.01" x 4.01" Weight 384g / 0.84lbs Power 12VDC (+9 - +15VDC) *Specification are subject to change without notice. 18 QUESTIONS Visit us: www.aidaimaging.com/support E-mail us: support@aidaimaging.com Give us a Call: Toll Free: 844.631.8367 | Tel: 909.333.7421 Operating Hours: Mon-Fri | 8:00am 5:00pm PST 19 Disposal of Old Appliances 1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately form the municipal waste stream in accordance to laws designated by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful inter reference in which case the user will be required to correct the interference at his own expense. 20