Altronix Home
Installation Guide for Altronix models including: Pace1ST Hardened Transceiver, Pace1ST, Hardened Transceiver, Transceiver
Altronix PACE1ST | Long Range Ethernet Single Port Small Tra
File Info : application/pdf, 4 Pages, 752.48KB
DocumentDocumentPace1ST Hardened Transceiver IP and PoE+ Over I.T.E. 43KC Extended Distance CAT5e Installation Guide Overview: Pace1ST is a long range hardened Ethernet transceiver designed for use with Pace1PRM, Pace4PRM, Pace8PRM and Pace16PRM receivers. They transmit data at 100Mbps full duplex and power via CAT5e or higher cable in a PoE(+) compliant format. Pace1ST will not deliver power to non-compliant devices, thus avoiding damage to improperly connected non-PoE cameras/devices. The receiver passes the PoE(+) compliant power over the cable to the Pace1ST transceiver which, in turn, passes this power to an enabled IP camera/device. These plug and play units facilitate cost-effective solutions for IP devices that need to be installed at distances greater than 100m. Features: Agency Listings: · UL/cUL Listed for Information Technology Equipment (UL 60950-1). · CE European Conformity. Input: · PoE (15W) IEEE 802.3af compliant or PoE+ (30W) IEEE 802.3at compliant from Pace1PRM, Pace4PRM, Pace8PRM or Pace16PRM. Ethernet: · Connectivity: RJ45, auto-crossover. · Wire type: 4-pair CAT5e. · Speed: 10/100BaseT, half/full duplex, auto negotiation. PoE compliant to IEEE 802.3af (15W) and PoE+ compliant to IEEE 802.3at (30W) delivered to camera by Pace1ST. · Throughput is rated to pass 100Mbps of data. CAT5e or Higher: · Distance: up to 500m @ 100Mbps. LED Indicators: · Green - PoE active. · Yellow and Green LED IP Link status, 10/100Base-T/active. Environmental: · Operating Temperature: For 15W: 40ºC to 75ºC ( 40ºF to 167ºF). For 30W: 40ºC to 49ºC ( 40ºF to 120ºF). · Storage Temperature: 40ºC to 75ºC ( 40ºF to 167ºF). · Relative humidity: 20 to 85%, non-condensing. Functions: · Auto detection and protection of legacy non-PoE cameras/devices. Applications: · Retrofit digital IP cameras in an analog CCTV CAT5e installations. · Extend Network link distance in an industrial environment over 610m. · Works with Megapixel, HD720, HD1080 and VGA (SD) cameras with proper headend equipment. Mechanical: · Dimensions (W x L x H approx.): 2.27" x 2.645" x 1.12" (57.7mm x 67.2mm x 28.4mm). Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. Pace1ST is not intended to be connected to outside plant leads and should be installed indoors within the protected premises. Pace1ST is intended for indoor use only. 1. Secure unit to desired mounting surface with a proper fastening device utilizing the case's mounting hole (Fig. 2a, pg. 3). Unit should be mounted in the proximity of camera/device. 2. Connect structured cable from IP camera/device to RJ45 jack marked [IP Device] (Fig. 2, pg. 3). 3. Connect CAT5e or higher to the connector marked [Pace Receiver] from receiver (Pace1PRM, Pace4PRM, Pace8PRM or Pace16PRM) (Fig. 2, pg. 3). Caution: once PoE connection is established between the receiver and Pace1ST, disconnection from Pace1ST will not disable the PoE output voltage on the receiver. Although the Pace1ST can be reconnected, caution should be taken not to connect the CAT5e wiring from the receiver to any non-PoE device. Parameter Connections Input power requirements Indicators Environmental Conditions Regulatory Compliance Weights (approx.) Technical Specifications: Description RJ45 for ethernet link. PoE (15W) IEEE 802.3af compliant or PoE+ (30W) IEEE 802.3at compliant from Pace1PRM, Pace4PRM, Pace8PRM or Pace16PRM. Yellow (RJ45 connector): Green (RJ45 connector): Green: On - Link, Off - No Link, Blinking - Activity. On - 100Base-TX, Off - 10Base-T. PoE Active. Operating Ambient Temperature (UL60950-1): For 15W: 40ºC to 75ºC ( 40ºF to 167ºF). For 30W: 40ºC to 49ºC ( 40ºF to 120ºF). Relative Humidity: 20 to 85%, non-condensing. Storage Temperature: 40ºC to 75ºC ( 40ºF to 167ºF). Operating Altitude: 304.8 to 2,000m. UL/cUL Listed for Information Technology Equipment (UL 60950-1). CE European Conformity. Product: 0.22 lb. (0.1 kg) | Shipping: 0.4 lb. (0.18 kg). Fig. 1 Pace1ST Pace PoE Receiver Out IP Device CAT5e or higher Cable out to Pace Receiver (Pace1PRM, Pace4PRM, Pace8PRM or Pace16PRM) Green LED indicates PoE out to Device CAT5e or higher Cable from Camera/Device - 2 - Pace1ST Installation Guide Fig. 2 Pace1PRM Single PoE Camera Connection: Mounting Hole Pace1PRM - Receiver IP-UTP Receiver Passes PoE/PoE+ RJ45 LEDs Yellow - Activity Green - Speed Green LED Power and PoE I.T.E. 43KC UTP Link Z1409 www.altronix.com Output Input RJ45 PoE PoE PoE Link LED Input LED Pace1ST PoE Camera Pace1ST - Transceiver Supports PoE/PoE+ RJ45 LEDs Green LED Yellow - Speed Green - Activity Power and PoE I.T.E. 43KC Pace Receiver www.altronix.com PoE Out IP Device Fig. 2a PoE+ over CAT5e up to 500m max. 100m max. Powered Switch or MidSpan PoE compliant 100m max. Legend: Structured Cable Multiple PoE Cameras Connection: Pace8PRM shown. Pace4PRM and Pace16PRM are similar, Fig. 3 with four (4) and sixteen (16) channels respectively. OUT Ports 1 4 IN OUT Ports 5 8 IN 100m max. Powered Switch or NetWay MidSpan 500m max. 500m max. 500m max. 500m max. 500m max. 500m max. 500m max. 500m max. PoE compliant Pace1ST 100m max. PoE compliant Pace1ST 100m max. PoE compliant Pace1ST 100m max. PoE compliant Pace1ST 100m max. PoE compliant Pace1ST 100m max. PoE compliant Pace1ST 100m max. PoE compliant Pace1ST 100m max. PoE compliant Pace1ST 100m max. PoE Camera PoE Camera PoE Camera PoE Camera PoE Camera PoE Camera PoE Camera PoE Camera Pace8PRM - Front Panel Pace1ST Pace1ST Installation Guide - 3 - Maximum Length of Cable Type vs. Camera Power/PoE Class: Cable Type Total Power Consumption Max. Data Distance Max. Power Distance CAT5e CAT5e 15W 500m 500m 30W 500m 423m Note: Calculations based on 56VDC starting voltage from power source and accounts for a 10VDC voltage drop. IEEE standards voltage range requirement for powered devices are: PoE (15W) - 37VDC to 57VDC PoE+ (30W) - 44VDC to 57VDC. Notes: Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty IIPace1ST Rev. 111413 I08U MEMBER - 4 - Pace1ST Installation Guide