Philips Water All-in-One Water Station ADD5980M/79
Introduction
This document serves as the user manual for the Philips Water All-in-One Water Station, model ADD5980M/79. It provides essential information for the safe installation, operation, and maintenance of your appliance. Please read this manual carefully before using the product and keep it for future reference.
Key Features
- Instant Heating: Provides hot water at various temperatures within seconds, ideal for beverages and cooking.
- Chilled Water: Offers refreshing chilled water, cooling down to approximately 8°C on demand.
- Micro X-Clean Filtration: Utilizes advanced filtration technology to purify water, reducing impurities and enhancing taste.
- Convenient Operation: Designed for ease of use with intuitive controls.
Safety Information
⚠️ Important Safeguards:
- Always ensure the appliance is connected to a grounded power outlet.
- Do not immerse the appliance, cord, or plug in water or other liquids.
- Keep the appliance away from hot surfaces and open flames.
- This appliance is intended for household use only.
- Ensure the water tank is filled before operating the heating or cooling functions.
- Do not attempt to service the appliance yourself. Contact Philips customer support for assistance.
Operation Guide
Getting Started
- Unpack the appliance and remove all packaging materials.
- Place the water station on a stable, flat surface near a power outlet.
- Insert the Micro X-Clean filter cartridge into the designated compartment.
- Fill the water tank with fresh, cold water up to the MAX line.
- Plug in the appliance and follow the on-screen prompts or button controls to select desired water temperature and volume.
Dispensing Water
- Select your desired temperature (e.g., ambient, 85°C, 95°C, 100°C) and dispense volume.
- Place your cup or container under the dispenser nozzle.
- Press the dispense button.
Chilled Water
- Activate the cooling function by pressing the designated button.
- Allow a few minutes for the water to chill to the desired temperature (approx. 8°C).
- Dispense chilled water as needed.
Maintenance and Care
Filter Replacement
The Micro X-Clean filter should be replaced after 100 litres of water or every 30 days, whichever comes first, to ensure optimal performance and water quality. A filter replacement indicator may alert you when it's time.
- Turn off and unplug the appliance.
- Open the filter compartment and remove the old filter cartridge.
- Insert a new, genuine Philips Micro X-Clean filter cartridge.
- Close the compartment securely.
- Reset the filter indicator if applicable.
Cleaning the Appliance
Regular cleaning helps maintain hygiene and performance. Wipe the exterior with a damp cloth. The drip tray is usually removable for cleaning.
- Unplug the appliance before cleaning.
- Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Remove and wash the drip tray with mild soap and water. Rinse and dry thoroughly before reinserting.
- Periodically descale the appliance according to manufacturer recommendations if mineral buildup is observed.
Troubleshooting
If you encounter issues, consult the following common problems:
- No power: Ensure the power cord is securely plugged in and the outlet is functional.
- Water not dispensing: Check if the water tank is filled and the filter is correctly installed. Ensure no error codes are displayed.
- Water not hot/cold enough: Allow sufficient time for heating/cooling. Ensure the appliance is not overloaded.
- Unusual noise: Some operational noises are normal, especially during heating or cooling cycles. If noise is excessive, contact support.
For further assistance, refer to the full user manual or contact Philips customer support.
Specifications
Model: ADD5980M/79
Brand: Philips
Filtration Type: Micro X-Clean
Features: Instant Heating, Chilled Water Dispensing
Power Supply: [Specify voltage/frequency if known, otherwise omit or use placeholder]
Dimensions: [Specify dimensions if known]
Weight: [Specify weight if known]
