flyduino · GitHub
Instruction Manual for FETTEC models including: SW26, KISS FC Flight Controller, SW26 KISS FC Flight Controller, FC Flight Controller, Flight Controller, Controller
Introduction Thank you for purchasing the FETtec FC. This is a KISS licensed F7 Flight-controller Features • KISS FC firmware • 2S-6S Lipo voltage
FETtec KISS FC | FETtec
File Info : application/pdf, 11 Pages, 5.68MB
DocumentDocumentFETtec KISS FC Manual Page 1 Table of Contents Introduction.....................................................................................................................................3 Features..........................................................................................................................................3 Safety warning................................................................................................................................3 Connection Diagram.......................................................................................................................4 Top/Bottom Layout......................................................................................................................4 Dimension (in mm).....................................................................................................................5 FC Version 1.2............................................................................................................................5 Basic Setup.....................................................................................................................................6 8 pin connection.........................................................................................................................6 Receiver connection (RX)..........................................................................................................7 FrSky R-XSR..............................................................................................................................7 Crossfire nano connection..........................................................................................................8 VTX connection (Unify nano).....................................................................................................9 Camera connection..................................................................................................................10 Resetbutton..............................................................................................................................10 KISS Firmware .............................................................................................................................11 Technical details............................................................................................................................11 Page 2 Introduction Thank you for purchasing the FETtec FC. This is a KISS licensed F7 Flight-controller Features · KISS FC firmware · 2S-6S Lipo voltage · Dimensions 35x30mm without 30x30 corners 20x20mm (with breakable holes M2 to M3) 30x30mm hole distance useable (breakable 30x30mm corners) · F7 Processor [DShot 2400, Oneshot, Onewire] · Direct places for RX and VTX (unify nano, CRSF nano, FrSky R9) · Build-in real Pit-Mode for unify nano (via VTX Pin and 5V on SER1) · Dedicated onboard 5V BEC for VTX (max 600mA) · Motor Signal and GND pads in each corner · 8 pin connector for solder free FETtec ESC connection Safety warning · Remove propeller before flashing and configuration Page 3 Connection Diagram Top/Bottom Layout Signal1-4 Motor Signal 1-4 ESCTLM Telemetry (Serial) GND Reference Signal Ground UPRT Receiver signal port (SBUS / F-Port / PPM / Crossfire TX) RXTLM Receiver telemetry (sPort / Crossfire RX) Serial connectors (SER1&SER3) are JST-SH-1mm 6-pin Page 4 Dimension (in mm) Dimensions 35x30mm without 30x30mm corners · 20x20mm (with breakable holes M2 to M3) · 30x30mm hole distance useable (breakable 30x30mm corners) FC Version 1.2 Page 5 Basic Setup 8 pin connection (JST-SH-1mm 8-pin) FETtec KISS FC to FETtec ESC (cable included by FETtec ESC) Page 6 Receiver connection (RX) Top&Bottom connectors for receivers (bottom connector JST-SH-1mm 4-pin) FrSky R-XSR Page 7 Crossfire nano connection cable connection 2,54mm pinheader connection Page 8 VTX connection (Unify nano) Page 9 Camera connection Notes: · RX and TX connection is only for cameras that support serial · 5V (U5V) and Video (UVID) are only for use with a mounted unify PRO nano or unify PRO nano 32 Resetbutton Resets the FC to the preflashed bootloader Page 10 KISS Firmware For the latest KISS FC firmware and GUI please visit https://github.com/flyduino To update the FETtec FC firmware please use the KISS GUI and choose FETTEC KISS FC Technical details - STM32F7RET6 @ 216MHz - MPU6000 - Supply voltage 6-27V (2-6S LiPo) - 2x 5V BEC's (1x VTX with realpit, 1x all others) both max 600mA Page 11