P65Warnings.ca.gov
Installation Guide for T S models including: B-0123-ADF08, B-0123-B, B-0123 Series, B-0123 Series Pre Rinse Unit, Pre Rinse Unit, Rinse Unit, Unit
T&S Brass B-0123-ADF08 EasyInstall Pre-Rinse Unit Deck Mount Base 8" Adjustable Center
T&S Brass B-2430 at Wolff Design Center Plumbing showrooms serving Akron, Medina, Sandusky, and Toledo-Maumee, Ohio since 1965. - Akron-Medina-Sandusky-Toledo-Maumee-Ohio
T&S Brass B-0123-ADF12 Refacciones y Manuales | Parts Town México
File Info : application/pdf, 2 Pages, 663.74KB
DocumentDocumentInstallation and Maintenance Instructions
PRE-RINSE UNIT B-0123 Series
(B-0123-B, Pre-Rinse Unit w/ Wall Bracket)
Step 1: Apply plumber's putty to underside of inlets and plumber's tape to inlet threads. Line up water supply lines and couplings, attach and tighten with wrench.
:1 . .
Step 2: Apply plumber's tape to top of riser threads and attach to spring assembly. Tighten with wrench.
:2 .
.
Limited Three Year Warranty (Commercial Applications) T&S warrants to the original purchaser (other than for purposes of resale) that such product is free from defects in material and workmanship for a period of three (3) years from the date of purchase. During this three-year warranty period, if the product is found to be defective, T&S shall, at its option, repair and/or replace it. To obtain warranty service, products must be returned to.....
T&S Brass and Bronze Works, Inc. Attn: Warranty Repair Department 2 Saddleback Cove Travelers Rest, SC 29690
Shipping, freight, insurance, and other transportation charges of the product to T&S and the return of repaired or replaced product to the purchaser are the responsibility of the purchaser. Repair and/ or replacement shall be made within a reasonable time after receipt by T&S of the returned product. This warranty does not cover items which have received secondary finishing or have been altered or modified after purchase, or for defects caused by physical abuse to or misuse of the product, or shipment of the products.
Any express warranty not provided herein, and any remedy for Breach of Contract which might arise, is hereby excluded and disclaimed. Any implied warranties of merchantability or fitness for a particular purpose are limited to three years in duration. Under no circumstance shall T&S be liable for loss of use or any special consequential cost, expenses or damages.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. Specific rights under this warranty and other rights vary from state to state.
Attention California Residents: WARNING This product can expose you to chemicals including Lead, Chromium (hexavalent compounds) and Phthalates (DEHP) which are known to the State of California
to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
P/N: DATE: DRAWN: CHECKED: APPROVED:
098-014496-45 Rev.8 08-18-21 TED GEF 10-31-22 JHB 11-01-22
Step 3: Make sure that the EasyInstall® locking washer is seated properly inside the faucet body.
:3 EasyInstall®
.
Step 4:
Grab riser assembly and lower the EasyInstall® end-
fitting into faucet body. Press down until the end-
fitting "pops" in.
:4
.
EasyInstall® ""
.
Step 5: Lock the EasyInstall® locking nut in place and tighten with wrench.
:5 . EasyInstall®
Base Faucet Assemblies
1 Faucet Body Assembly w/ Eterna Cartridges
2 Faucet Body Assembly w/ Cerama Cartridges
2 Asm, Quarter-Turn Eterna Cartridge, RTC (new style)
3 Asm, Quarter-Turn Cerama Cartridge, RTC (new style)
3
Cartridge Only, Eterna w/ Spring Checks, RTC
3
Cartridge Only, Cerama w/ Check Valves, RTC
4 Asm, Quarter-Turn Eterna Cartridge, LTC (new style)
2 Asm, Quarter-Turn Cerama Cartridge, LTC (new style)
5
Cartridge Only, Eterna w/ Spring Checks, LTC
5
Cartridge Only, Cerama w/ Check Valves, LTC
6 Handle, Lever
4 Handle, Wrist Action
7 Screw, Handle
8 Index, Button - Hot (Red)
9 Index, Button - Cold (Blue)
10 Asm, Coupling Flange
11 Washer, Coupling Nut
12 Lock Washer, EasyInstall
Riser Assembly
13 Nipple, 3/8" x 24" 14 Swivel Assembly, EasyInstall 15 Swivel Piece 16 O-Ring, Swivel Piece 17 Asm, Finger Hook & Screw 18 Wall Bracket, 6" (add -B to model # for wall bracket)
Pre-Rinse Unit Assembly
19 Spring Body 20 Spring, Overhead 21 Asm, Flexible Stainless Steel Hoses 22 Asm, Spray Valve
Spray Valve Assembly
23 Washer, Hold Down Assembly 24 Ring, Hold Down Assembly 25 Body, Spray Valve (no handle) 26 Handle 27 Nut, Handle 28 Screw, Handle 29 Nipple 30 Cup, Spray * 31 Ring, Sprayhead * 32 Sprayface * 33 Screw, Sprayface
Bonnet Assembly
34 Asm, Bonnet * 35 Stem * 36 Washer, Seat * 37 Washer, Bonnet Binding
38 Bonnet * 39 Washer, Bonnet Brass * 40 Stem, Packing * 41 Spring, Bonnet
42 Push Button * 43 Grease Pack (o-ring lubricant)
* Parts included in B-10K parts kit
B-0220-LN B-0220-CR-LN 002712-40NS 012446-25NS 012443-40NS 012394-25NS 002711-40NS 012447-25NS 012442-40NS 012395-25NS 001638-45NS
B-WH4-NS 000925-45 001193-19NS 018506-19NS
00AA 001019-45 014200-45
000372-40 EZ-K N/A
001065-45 004R
B-0109-01
000821-40 000888-45 B-0044-H B-0107
010476-45 000907-45 000065-40 001120-45 003198-45 003199-45 000694-40 000019-40 007861-45 001121-45 000913-45
002856-40 001097-45 012915-45 001040-45 000608-25 000974-45 001100-45 000895-45 000753-25 012665-45
OPTIONAL (-B Models)
Wall Bracket Installation:
1. Fasten wall flange to wall using wall mount screws
Set Screws (2)
)2(
18
2. Place 2-piece clamp assembly around riser and tighten clamp screws securely.
3. Tighten set screws securely.
34 26
27 28
42 41
Clamp Screws (2)
)2(
24
20
23
)B- (
25
:
29
...21
30
.
. .3
31
21
32
33
23
43 19
39 40 39 38 37 36 35 8
13 22
17 9
7
14
6
2
15 4
3
12
16
5
1
11
10
10