Autonics MT4Y Series 4-Digit Multi Panel Meters

Instruction Manual

Model: MT4Y Series

Document ID: TCD220016AA

Introduction

Thank you for choosing our Autonics product. Read and understand the instruction manual and manual thoroughly before using the product. For your safety, read and follow the below safety considerations before using. For your safety, read and follow the considerations written in the instruction manual, other manuals and Autonics website. Keep this instruction manual in a place where you can find easily. The specifications, dimensions, etc. are subject to change without notice for product improvement. Some models may be discontinued without notice. Follow Autonics website for the latest information.

Safety Considerations

⚠️ Warning Failure to follow instructions may result in serious injury or death.

01. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or substantial economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime / disaster prevention devices, etc.) Failure to follow this instruction may result in personal injury, economic loss or fire.
02. Do not use the unit in the place where flammable / explosive / corrosive gas, high humidity, direct sunlight, radiant heat, vibration, impact or salinity may be present. Failure to follow this instruction may result in explosion or fire.
03. Install on a device panel to use. Failure to follow this instruction may result in fire or electric shock.
04. Do not connect, repair, or inspect the unit while connected to a power source. Failure to follow this instruction may result in fire or electric shock.
05. Check 'Connections' before wiring. Failure to follow this instruction may result in fire.
06. Do not disassemble or modify the unit. Failure to follow this instruction may result in fire or electric shock.

⚠️ Caution Failure to follow instructions may result in injury or product damage.

01. When connecting the power / measurement input and relay output, use AWG 24 (0.20 mm²) to AWG 15 (1.65 mm²) cable or over and tighten the terminal screw with a tightening torque of 0.98 to 1.18 N m. Use the wiring suitable for the load current capacity. Failure to follow this instruction may result in fire or malfunction due to contact failure.
02. Use the unit within the rated specifications. Failure to follow this instruction may result in fire or product damage.
03. Use a dry cloth to clean the unit, and do not use water or organic solvent. Failure to follow this instruction may result in fire or electric shock.
04. Keep the product away from metal chip, dust, and wire residue which flow into the unit. Failure to follow this instruction may result in fire or product damage.

Cautions during Use

Follow instructions in 'Cautions during Use'. Otherwise, It may cause unexpected accidents.
Power supply should be insulated and limited voltage / current or Class 2, SELV power supply device.
Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting the power.
Use twisted pair wire for communication line.
Keep away from high voltage lines or power lines to prevent inductive noise. In case installing power line and input signal line closely, use line filter or varistor at power line and shielded wire at input signal line.
Do not use near the equipment which generates strong magnetic force or high frequency noise.

Connection with the line filter

Install the line filter close to the panel meter.

Connection with the varistor

Panel meter [HI] [LOW] 110/220 VAC~ Earth ground

This unit may be used in the following environments.

Indoors (in the environment condition rated in 'Specifications')
Altitude max. 2,000 m
Pollution degree 2
Installation category II

Ordering Information

This is only for reference, the actual product does not support all combinations. For selecting the specified model, follow the Autonics website.

Model structure: MT4Y - [Input type] - [Preset output + Sub output] - 4

Input Type

DV: DC voltage ⁰¹⁾
DA: DC current
AV: AC voltage ⁰²⁾
AA: AC current ⁰²⁾

Preset output

N: None (indicator)
0: Relay
1: NPN open collector
2: PNP open collector
3: Relay (Low out)
4: Relay (Low out)

Sub output

Transmission (DC 4-20 mA)
RS485 Communication
BCD Dynamic
Low speed serial

⁰¹⁾ To measure the current over DC 5 A, please select DV type because the shunt should be used.

⁰²⁾ In case of selecting frequency display, no output will be provided even if it is output support model.

Product Components

Product
Bracket X 2
Instruction manual
Unit sticker X 1

Manual & Software

Manual

For proper use of the product, refer to the manuals and be sure to follow the safety considerations in the manuals. Download the manuals from the Autonics website.

Software

Download the installation file and the manuals from the Autonics website.

DAQMaster

It is the comprehensive device management program for Autonics' products, providing parameter setting, monitoring and data management.

Dimensions

Unit: mm. For detailed drawings, refer to the Autonics website.

Main dimensions: 72 (Width) x 36 (Height) x 66.5 (Depth)

Panel cut-out: 68+0.7 / 31.5+0.5

(Diagram description: A rectangular panel meter with dimensions shown. A separate diagram shows the panel cut-out dimensions.)

Cautions during Wiring

Use Copper-conductor wire with the temperature class 60 °C.

Unit: mm. Use terminals of the specified size below. Contact the manufacturer for the socket and cable.

Connector details:

Model: Hirose connector HIF3BA-14PA-2.54DS
Socket: Hirose connector socket HIF3BA-14D-2.54R

(Diagram description: Shows a Hirose connector and socket with pin numbers.)

Connections

Input

DC voltage

Terminals: SOURCE, COM, 1234567. Ranges: 250 mVDC to 500 VDC.

DC current

Terminals: SOURCE, COM, 1234567. Ranges: 5 mA to 5 A.

AC voltage

Terminals: SOURCE, COM, 1234567. Ranges: 1 VAC to 500 VAC.

AC current

Terminals: SOURCE, COM, 1234567. Ranges: 50 mA to 5 A.

Output

0: Relay: Terminals 8-13. Functions: HOLD/ZERO, HI, GO, LO, COM.
1: NPN open collector: Terminals 8-13. Functions: HOLD/ZERO, HI, GO, LO, COM.
2: PNP open collector: Terminals 8-13. Functions: HOLD/ZERO, HI, GO, LO, COM.
3: Relay + Transmission (DC 4-20 mA): Terminals 8-13. Includes +,- for DC 4-20 mA OUT1, HOLD/ZERO. Load resistance ≤ 600 Ω.
4: Relay + RS485 comm.: Terminals 8-13. Includes RS485, OUT1, HOLD/ZERO, COM.
5: BCD Dynamic: Terminals 8-13. Includes COM, B, D, D1, D3, POL.
6: Low speed serial: Terminals 8-13. Includes COM, CLOCK, DATA, LATCH, POL. POL function: When a display value is negative (-), the signal of (-) will be outputted.

Specifications

Model	MT4Y-DV-4	MT4Y-DA-4	MT4Y-AV-4	MT4Y-AA-4
Input type	DC voltage	DC current	AC voltage ⁰¹⁾	AC current ⁰¹⁾
Max. allowable input	110% F.S. for each measured input range
Display method	7-segment (red) LED (character height: 14.2 mm)
Display accuracy (23±5°C)	±0.1% F.S. rdg ± 2 digit	±0.1% F.S. rdg ± 2 digit	±0.3% F.S. rdg ± 3 digit ⁰²⁾	±0.3% F.S. rdg ± 3 digit
Max. display range	-1999 to 9999 (4 digit)
A/D conversion method	ΣΔ (Sigma Delta) ADC
Sampling cycle	50 ms	16.6 ms
Unit weight (packaged)	≈ 134 g (≈ 213.5 g)
Approval	CE, CUS, EAC
Preset output	Relay / NPN open collector / PNP open collector output model	None (indicator) / Relay / NPN open collector / PNP open collector output model
Preset output contact capacity	250 VAC~3A, 30 VDC~3A. Contact composition: N.O (1a)
Preset output capacity	≤ 12-24 VDC ±2 VDC, 50 mA resistive load
Sub output	None (indicator) / BCD Dynamic / Low speed serial / RS485 Communication output model	Transmission (DC 4-20 mA) / RS485 Communication / BCD Dynamic / Low speed serial output model
Sub output (NPN open collector)	Output capacity: ≤ 12-24 VDC, 50 mA resistive load
Sub output (Transmission)	Resolution: 1/12,000 (load resistance: ≤ 600 Ω). Response time: ≤ 450 ms
Sub output (RS485)	Protocol: Modbus RTU
Power supply	100-240 VAC~±10% 50/60 Hz
Power consumption	5 VA
Insulation resistance	Between external terminal and case: ≥ 100 MΩ (500 VDC~ megger)
Dielectric strength	Between external terminal and case: 2,000 VAC~50/60 Hz for 1 min
Noise immunity	±2 kV square wave noise (pulse width: 1 µs) by the noise simulator
Vibration	0.75 mm double amplitude at frequency of 10 to 55 Hz (for 1 min) in each X, Y, Z direction for 2 hours
Vibration (malfunction)	0.5 mm double amplitude at frequency of 10 to 55 Hz (for 1 min) in each X, Y, Z direction for 10 min
Shock	300 m/s² (≈ 30 G) in each X, Y, Z direction for 3 times
Shock (malfunction)	100 m/s² (≈ 10 G) in each X, Y, Z direction for 3 times
Relay life cycle	Mechanical: ≥ 20,000,000 operations. Electrical: ≥ 100,000 operations (250 VAC~3A resistive load)
Ambient temp.	-10 to 50 °C, storage: -20 to 60 °C (no freezing or condensation)
Ambient humi.	35 to 85 %RH, storage: 35 to 85 %RH (no freezing or condensation)
Insulation type	Symbol: ⛋, double or reinforced insulation (dielectric strength between the measurement input part and the power part: 1 kV)

⁰¹⁾ Available frequency display, Display accuracy (23±5°C): ±0.1% F.S. rdg ± 2 digit

⁰²⁾ 5 A terminal: ±0.3% F.S. rdg ± 3 digit

Communication Interface

RS485

Comm. protocol	Modbus RTU
Application standard	Compliance with EIA RS485
Max. connection	31 units (address: 01 to 99)
Comm. synchronous method	Asynchronous
Comm. method	2-wire half duplex
Comm. distance	≤ 800 m
Comm. speed	1,200/1,400/4,800/9,600/19,200/38,400 bps
Start bit	1-bit (fixed)
Data bit	8-bit (fixed)
Parity bit	None, Even, Odd
Stop bit	1-bit, 2-bit
EEPROM life cycle	≈ 1,000,000 operations (Erase / Write)

Mode Setting

Parameter 1 group

Parameter	Mark	Defaults	Setting range	Display condition
Input range	1-1	-	Refer to Input Range and Display Range	[DC voltage model], [AC voltage model]
Input range	1-1	-	Refer to Input Range and Display Range	[DC current model], [AC current model]
Display method	1-2	STND	STND: standard, SCAL: scale, FREQ: frequency ⁰¹⁾	-
Measurement method	1-3	tRMS	T.RMS: True RMS, A.RMS: Average RMS, AVG: Average	[AC voltage model], [AC current model]
Max. display value	1-4	STND	(fixed)	1-2 Display method: STND
High-limit display value correction	1-5	INbH	500	[DC voltage model], [AC voltage model] Max. value of display range
High-limit display value correction	1-5	%000	[DC current model], [AC current model] Max. value of display range	-
High-limit display value correction	1-5	!000	0.100 to 5.000 %	-
Low-limit display value deviation correction	1-6	INbL	00	-99 to 99
Decimal point position	1-7	DOT	)0	[DC voltage model], [AC voltage model] 0, 0.0, 0.00, 0.000
Decimal point position	1-7	DOT	)000	[DC current model], [AC current model] 0, 0.0, 0.00, 0.000
High-limit scale	1-8	H-SC	Display value against max. measurement input*	1-2 Display method: SCAL & 1-7 Decimal point
Low-limit scale	1-9	L-SC	Display value against min. measurement input*	-
High-limit display value correction	1-10	INbH	!000	0.100 to 5.000 %	1-2 Display method: STND
Low-limit display value deviation correction	1-11	INbL	00	-99 to 99 ⁰²⁾	-
Decimal point position	1-12	DOT	)0	[AC voltage model] 0, 0.0, 0.00, 0.000	-
Decimal point position	1-12	DOT	)000	[AC current model] 0, 0.0, 0.00, 0.000	-
High-limit display value correction	1-13	INbH	!000	0.100 to 9.999	1-2 Display method: FREQ
Exponent of INB	1-14	INbE	10-0	10⁰: 10⁰, 10^-1: 10^-1, 10^-2: 10^-2, 10¹: 10¹	-

⁰¹⁾ Displays at AC voltage or AC current model only.

⁰²⁾ Low-limit display value deviation correction range is within -99 to 99 for D0, D-1 digit regardless of decimal point position.

Frequency measurement range

Decimal point	Display range	Frequency measurement range
-	0 -1999 to 9999	1 to 9999 Hz
)0	-199.9 to 999.9	0.1 to 999.9 Hz
)00	-19.99 to 99.99	0.10 to 99.99 Hz
)000	-1.999 to 9.999	0.100 to 9.999 Hz

Parameter 2 group

Parameter	Mark	Defaults	Setting range	Display condition
Output operation mode	2-1	OUtT	OFF	OFF, L.ST, H.ST, LH.ST, HH.ST, LL.ST, LD.ST. Refer to Output Operation Mode. Relay (Low out) output model is available only OFF or L.ST.
Hysteresis	2-2	HYS	001	[Except indicator model] Within 10 % of max. display range, digit
Startup compensation time	2-3	STaT	0)0	[Except indicator model] 0.0 to 99.9 sec
Peak monitoring delay time	2-4	PEkT	00	00 to 30 sec
Display cycle	2-5	DIsT	)2 S	0.1 to 5.0 sec
Keys for zero adjustment	2-6	ZERO	NO	NO, YES. YES: Press the [] + [] keys for 3 sec to adjust zero.
External input terminal	2-7	EVLN	HOLD	[Except indicator model] HOLD, ZERO. If the external input terminal is short-circuited for 50 ms or more, it operates with the set function.
High-limit value of transmission output	2-8	FS-H	500	[DC voltage & Transmission (DC 4 - 20 mA) output model] -5 to 110 % of display range. [AC voltage & Transmission (DC 4 - 20 mA) output model] 0 to 110 % of display range.
High-limit value of transmission output	2-8	%000	[DC current & Transmission (DC 4 - 20 mA) output model] -5 to 110 % of display range. [AC current & Transmission (DC 4 - 20 mA) output model] 0 to 110 % of display range.	-
Low-limit value of transmission output	2-9	FS-L	000	[DC voltage & Transmission (DC 4 - 20 mA) output model] Min. value of display range. [AC voltage & Transmission (DC 4 - 20 mA) output model] Min. value of display range.
Low-limit value of transmission output	2-9	)000	[DC current & Transmission (DC 4 - 20 mA) output model] Min. value of display range. [AC current & Transmission (DC 4 - 20 mA) output model] Min. value of display range.	-
Comm. Address	2-10	ADRS	01	[RS485 Comm. output model] 01 to 99
Comm. speed	2-11	BPS	9600	[RS485 Comm. output model] 38.4k, 19.2k, 9600, 4800, 2400, 1200 bps
Parity bit	2-12	PRTY	NONE	[RS485 Comm. output model] NONE, EVEN, ODD
Stop bit	2-13	STP	2	[RS485 Comm. output model] 2, 1 bit
Response waiting time	2-14	RSwT	5	[RS485 Comm. output model] 5 to 99 sec
Lock	2-15	LOC	OFF	OFF: unlock, LOC1: lock parameter 1, LOC2: lock parameter 1, 2, LOC3: lock parameter 0, 1 and 2

Parameter 0 group

Parameter	Mark	Defaults	Setting range	Display condition
Output high-limit output setting value	0-1	hSET	500	[DC voltage & Preset setting model] -5 to 110 % of display range [AC voltage & Preset setting model] 0 to 110 % of display range
Output high-limit output setting value	0-1	%000	[DC current & Preset setting model] -5 to 110 % of display range [AC current & Preset setting model] 0 to 110 % of display range	2-1 Output operation mode: except OFF
Output low-limit output setting value	0-2	lSET	000	[DC voltage & Preset setting model] Min. value of display range [AC voltage & Preset setting model] Min. value of display range	2-1 Output operation mode: except OFF
Output low-limit output setting value	0-2	)000	[DC current & Preset setting model] Min. value of display range [AC current & Preset setting model] Min. value of display range	2-1 Output operation mode: except OFF
Display max. peak value ⁰¹⁾	0-3	hPEK	)0	[DC voltage], [AC voltage] Max. peak value in run mode	2-1 Output operation mode: except OFF & 2-4 Peak monitoring delay time: except 00
Display max. peak value ⁰¹⁾	0-3	)000	[DC current], [AC current] Max. peak value in run mode	2-1 Output operation mode: except OFF & 2-4 Peak monitoring delay time: except 00
Display min. peak value ⁰¹⁾	0-4	lPEK	)0	[DC voltage], [AC voltage] Min. peak value in run mode	2-1 Output operation mode: except OFF & 2-4 Peak monitoring delay time: except 00
Display min. peak value ⁰¹⁾	0-4	)000	[DC current], [AC current] Min. peak value in run mode	2-1 Output operation mode: except OFF & 2-4 Peak monitoring delay time: except 00

⁰¹⁾ Reset: Press any one of [], [], [] keys.

Input Range and Display Range

When the max. input value is over the 100 %, it may result in input terminal damage.

DC voltage model

Input range	Display range (STND)	Display range (SCAL) ⁰¹⁾	Input impedance
0 - 500 VDC	0.0 to 500.0	500V	4.33 MΩ
0 - 100 VDC	0.0 to 100.0	100V	4.33 MΩ
0 - 50 VDC	0.00 to 50.00	50V	433.48 kΩ
0 - 10 VDC	0.00 to 10.00	10V	433.48 kΩ
0 - 5 VDC	0.000 to 5.000	5V	43.48 kΩ
0 - 1 VDC	0.000 to 1.000	1V	43.48 kΩ
0 - 250 mVDC	0.0 to 250.0	)25V	2.28 kΩ
0 - 50 mVDC	0.00 to 50.00	50MV	2.28 kΩ

Decimals

Decimal point	Display range
-	0 -1999 to 9999
)0	-199.9 to 999.9
)00	-19.99 to 99.99
)000	-1.999 to 9.999

⁰¹⁾ Connect to the input terminals whose 30 % to 100 % of the input range includes the max. value of the input range to measure. When the max. input value is under the 30 % of the input terminal range, display accuracy is degraded.

DC current model

Input range	Display range (STND)	Display range (SCAL) ⁰¹⁾	Input impedance
0 - 5 A	0.000 to 5.000	5A	0.02 Ω
0 - 2 A	0.000 to 2.000	2A	0.02 Ω
0 - 500 mA	0.0 to 500.0	)5A	0.22 Ω
0 - 200 mA	0.0 to 200.0	)2A	0.22 Ω
0 - 50 mA	0.00 to 50.00	50MA	2.22 Ω
4 - 20 mA	4.00 to 20.00	4-20	2.22 Ω
0 - 5 mA	0.000 to 5.000	5MA	22.22 Ω
0 - 2 mA	0.000 to 2.000	2MA	22.22 Ω

Decimals

Decimal point	Display range
-	0 -1999 to 9999
)0	-199.9 to 999.9
)00	-19.99 to 99.99
)000	-1.999 to 9.999

AC voltage model

Input range	Display range (STND)	Display range (SCAL) ⁰¹⁾	Input impedance
0 - 500 VAC	0.0 to 500.0	500V	5.01 MΩ
0 - 250 VAC	0.0 to 250.0	250V	5.01 MΩ
0 - 110 VAC ⁰²⁾	0.0 to 440.0	110P	1.11 MΩ
0 - 50 VAC	0.00 to 50.00	50V	1.11 MΩ
0 - 20 VAC	0.00 to 20.00	20V	200.92 kΩ
0 - 10 VAC	0.00 to 10.00	10V	200.92 kΩ
0 - 2 VAC	0.000 to 2.000	2V	20.92 kΩ
0 - 1 VAC	0.000 to 1.000	1V	20.92 kΩ

Decimals

Decimal point	Display range
-	0 -1999 to 9999
)0	-199.9 to 999.9
)00	-19.99 to 99.99
)000	-1.999 to 9.999

⁰²⁾ In case of 0 to 110 VAC of AC voltage range and using P.T (potential transformer) for 440 VAC / 110 VAC, if 110 VAC is input, and the unit displays 440 VAC automatically by preset scale value for P.T user's convenient.

AC current model

Input range	Display range (STND)	Display range (SCAL) ⁰¹⁾	Input impedance
0 - 5 A	0.000 to 5.000	5A	0.02 Ω
0 - 2.5 A	0.000 to 2.500	@5A	0.02 Ω
0 - 1 A	0.000 to 1.000	1A	0.10 Ω
0 - 500 mA	0.0 to 500.0	)5A	0.20 Ω
0 - 250 mA	0.0 to 250.0	)25A	0.20 Ω
0 - 100 mA	0.0 to 100.0	)1A	1.02 Ω
0 - 50 mA	0.00 to 50.00	50MA	1.02 Ω

Decimals

Decimal point	Display range
-	0 -1999 to 9999
)0	-199.9 to 999.9
)00	-19.99 to 99.99
)000	-1.999 to 9.999

Output Operation Mode

H.SET or L.SET is displayed according to the output operation mode setting. In case of output operation mode as OFF, H.SET and L.SET are not displayed. When changing output operation mode, high-limit / low-limit output setting value, hysteresis are reset.

MODE	Output operation	Preset output	LO	HI	GO	H.SET	L.SET	Display value
OFF	OFF	-	-	-	-	-	-	No output
L.ST	L.SET < Display value	-	ON	-	-	-	L.SET	-
H.ST	H.SET > Display value	-	-	ON	-	H.SET	-	-
LH.ST	L.SET < Display value < H.SET	-	ON	ON	-	H.SET	L.SET	-
HH.ST	Display value < L.SET or Display value > H.SET	-	ON	ON	-	H.SET	L.SET	-
LL.ST	L.SET > Display value	-	ON	-	-	-	L.SET	-
LD.ST	Display value < L.SET	-	ON	-	-	-	L.SET	Second L.SET Display value

Reset

Press the [] + [] + [] keys for over 5 sec. in run mode, INIT flashes for 0.5 sec.
Press the direction keys to flash NO for 0.5 sec in turn.
Change the setting value as YES by pressing the direction keys.
Press the [MODE] key to reset all parameter values as default and to return to run mode.

Error

Error display is released automatically when it is in the measured and display range.

Display	Description	Troubleshooting
HHHH LLLL ⁰¹⁾	Flashes when measurement input is exceeded the max. allowable input (110 %)	Disconnect power supply and check the cables.
HHHH LLLL ⁰¹⁾	Flashes when measurement input is exceeded the min. allowable input (-10 %)	Disconnect power supply and check the cables.
D-HH	Turns ON when display input is exceeded high-limit scale setting value or max. display range (9999)	Reset within the display range.
D-LL	Turns ON when display input is exceeded low-limit scale setting value or min. display range (-1999)	Reset within the display range.
F-HH	Turns ON when input frequency is exceeded the max. display value of measured range	-
OVER	Flashes twice when it exceeds zero range (±99) and returns to run mode	Reset within the zero range.

⁰¹⁾ Displays at DC input model only.

	Autonics MT4N Series: 4-Digit Multi Panel Meter Instruction Manual This instruction manual provides detailed guidance on the Autonics MT4N Series 4-Digit Multi Panel Meters, covering specifications, wiring, safety precautions, and operational parameters for industrial applications.
	Autonics MT4W Series 4-Digit Multi Panel Meters Instruction Manual Instruction manual for Autonics MT4W Series 4-Digit Multi Panel Meters, covering specifications, connections, parameter settings, and troubleshooting.
	Autonics MT4W Series Panel Meter Instruction Manual Comprehensive instruction manual for the Autonics MT4W Series panel meters, covering specifications, connections, parameter settings, and safety precautions for accurate measurement and control.
	Autonics Multi Pulse Meters MP5S/MP5Y/MP5W Series Product Manual This product manual provides detailed information on Autonics MP5S, MP5Y, and MP5W series multi pulse meters, covering features, safety guidelines, ordering, specifications, operation modes, functions, and connection examples.
	Autonics Industrial Automation Solutions Product Guide Explore the comprehensive Autonics Product Guide featuring industrial automation solutions including sensors, controllers, motion devices, power electronics, and networking components. Discover detailed specifications for various product series designed to enhance production efficiency and quality of life.
	Autonics Industrial Automation Solutions Product Guide Explore Autonics' comprehensive range of industrial automation solutions, including sensors, controllers, motion devices, safety products, and networking components, distributed by Valin Corporation. This product guide details specifications and features for enhanced production efficiency and quality of life.
	Autonics LE4S Series LCD Digital Timers Instruction Manual Instruction manual for Autonics LE4S Series LCD Digital Timers, covering safety considerations, ordering information, dimensions, unit descriptions, output operation modes, parameter settings, connections, and detailed specifications.
	Autonics LE3S Series LCD Digital Thumbwheel Switch Timers Instruction Manual Instruction manual for Autonics LE3S Series LCD Digital Thumbwheel Switch Timers, covering ordering information, product components, dimensions, safety considerations, cautions during use, specifications, output operation modes, time ranges, connections, and UP/DOWN mode.

Autonics MT4Y Series 4-Digit Multi Panel Meters

Introduction

Safety Considerations

Cautions during Use

Ordering Information

Input Type

Preset output

Sub output

Product Components

Manual & Software

DAQMaster

Dimensions

Cautions during Wiring

Connections

Input

DC voltage

DC current

AC voltage

AC current

Output

Specifications

Communication Interface

RS485

Mode Setting

Parameter 1 group

Parameter 2 group

Parameter 0 group

Input Range and Display Range

DC voltage model

DC current model

AC voltage model

AC current model

Output Operation Mode

Reset

Error

References

Related Documents